Print-ready 3D models

Doorknob Lever Adapter Clamp

A split-band clamp that grips a standard round door knob (50–56 mm, eleven internal 1.25 mm grip ribs) and adds a 95 mm lever arm so the door opens with a forearm, elbow or closed fist instead of a twisting grip. One M4 bolt through the 4.5 mm clearance ears pulls the 4 mm split shut onto a captured M4 nut; band is 22 mm tall, arm 14 mm thick, overall 139 x 63 mm, and it prints flat with the lever load in the XY plane.

Thumb Page Holder Ring

A one-handed reading aid: slip your thumb through the 22 mm ring and the two 29 mm wings press both page blocks flat so a paperback stays open by itself. Ramped wing tips slide under the pages without creasing them; 80 mm wide overall.

Sticky Note Pad And Pen Dock

A desk dock with a recessed tray sized for a standard 76 x 76 mm sticky note pad and a rounded rear trough for pens, pencils and erasers. A scalloped thumb notch in the front wall lets you peel notes one-handed; footprint is 86 x 113 mm and 20 mm tall.

Wall Mail And Key Rack

A 110 mm wall-mounted entryway rack with a 38 mm deep pocket for letters and bills plus three angled hooks with catch lips for keys. Two keyhole slots let it drop onto drywall screws at 88 mm spacing.

Wall-Mount Hair Dryer Holster

A screw-mounted holster that holds a hair dryer by its barrel in a 64 mm ring so the handle and cord hang clear of the counter. Plate is 62 x 62 mm with two 4.6 mm screw holes on 40 mm centers; the ring stands off the wall 36 mm.

Furniture Leg Riser Block

A hollow, rib-cored riser that lifts a bed, couch, desk or dresser leg 44 mm for extra under-furniture storage. The chamfered 58 mm socket accepts square or round legs, and a poke-out hole in the floor frees a stuck leg — order four for one piece of furniture.

Print-In-Place Turntable Caddy

A 100 mm lazy-susan tray that prints as one piece and spins straight off the plate — the deck is captured by a mushroom post and rides on low-friction ring lands. Holds spice jars, sauces, pens or craft supplies in a 90 mm bowl with a 10 mm rim and eight grip ribs.

Extension Cord Wall Wrap

A two-horn wall cleat for figure-eight wrapping an extension cord, air hose or rope, with flared post tips that keep the coil from slipping off. 120 mm wide, mounts with two countersunk screws and holds roughly a 50 ft 16-gauge cord.

Snap-Gate Carabiner Clip

A 60 mm one-piece carabiner whose gate is a built-in flexing spring arm — press it inward to hook on, and a capture nose stops it opening under load. Prints flat with no supports, no assembly, and no metal spring; sized for keys, water bottles, and bag straps.

AA AAA Battery Dispenser

A gravity-fed dual-channel dispenser that stacks 6 AA and 8 AAA cells and drops the next one into a front grab window with a retaining lip. Stands 92 mm tall on a shelf or screws to a wall through the two rear ears.

Outlet Cover Phone Shelf

A shelf that hangs on the center screw of a standard duplex outlet cover to hold a charging phone off the floor. 70 mm wide plate, 58 mm deep ledge with an 8 mm lip and a cord notch through the middle.

Broom And Mop Wall Gripper

A screw-on wall gripper whose springy C-jaws snap over a 20–26 mm broom, mop, rake or squeegee handle so it hangs off the floor. 60 mm back plate with two counterbored screw holes; 18 mm tall jaws with a 19 mm snap mouth.

Toothpaste Tube Squeezer Key

A winding key that grips the flat tail of a toothpaste or ointment tube in a 3.2 mm slot; twist the finger-hole knobs to roll the tube up and push every last bit out. 96 mm long with a Ø7 mm hang hole in one knob.

Sink-Side Sponge Caddy

A two-compartment caddy that sits beside the faucet to hold a sponge and scrub brush separately, with slotted drain holes in the bottom so water runs out instead of pooling. Fits a standard sponge; overall footprint 100 x 70 x 45 mm.

Wall Hook