Model catalog

Friction-Lock Ball Joint Gimbal

A print-in-place ball-and-socket gimbal for cameras, lidar pucks and sensor boards on a robot or drone frame: a Ø20 mm ball captured in a spherical socket with a 0.4 mm gap gives 360° pan and roughly ±33° tilt, and one M4 thumbscrew driven into a brass heat-set insert (5.5 mm bore) locks the angle without any springs or shims. The 50 x 34 x 5 mm base bolts down with four M3 screws on a 42 x 24 mm pattern, and the 26 x 26 mm top plate carries four M3 clearance holes on a 18 x 18 mm square; overall 50 x 34 x 48 mm.

5 mm To T8 Flexible Coupler

A printed beam-flexure shaft coupler that joins a 5 mm stepper shaft (NEMA 17) to an 8 mm T8 leadscrew, with three 60°-indexed relief slots so it absorbs misalignment instead of binding the nut. 20 mm OD x 44 mm long, 5.3 mm and 8.6 mm bores, four M3 self-tapping grub screws (two per hub at 90°).

5 mm Shaft Robot Drive Wheel

A 60 mm OD × 18 mm wide spoked drive wheel that slips onto any 5 mm motor shaft (NEMA 17, 37 mm gearmotor) and locks with an M3 set screw threaded into the 6.3 mm hub wall. The 8 mm × 2.5 mm rim groove seats a #64 rubber band as a tire, and 24 scallops in the flanges give traction if you run it bare — replaces the hub-and-tire set nobody stocks for one-off robot builds.

LM8UU Dual Bearing Pillow Block

A split-clamp pillow block that carries two LM8UU linear bearings (15 mm OD x 24 mm) in line on an 8 mm smooth rod, with a centre rib that stops the bearings against each other and two M3 clamp screws that pinch the flanks so nothing walks out. The 60 x 44 x 35 mm body bolts down through four M4 clearance holes on a 40 x 34 mm rectangle, putting the rod axis 21 mm above the mounting surface.

NEMA 17 Extrusion Motor Bracket

An L-bracket that mounts a NEMA 17 stepper to 2020 aluminium extrusion: 54 x 40 mm base with two M5 T-nut holes on 20 mm centres, and a 54 x 50 mm vertical face carrying the 31 mm square M3 bolt pattern plus a 22.6 mm pilot bore for the motor's centring boss. Twin 5 mm gussets carry motor torque in the strong XY direction and sit outboard of the bolt heads so a hex driver still reaches all four screws; a pair of 6 x 3 mm slots above the bore takes a cable tie for the motor lead.

Heat Shrink Tube Size Rack

A six-lane stadium-step rack that sorts cut heat-shrink tubing by diameter — troughs 8/10/12/14/17/20 mm wide take the common 3:1 sizes from 2.4 mm up to 12.7 mm, each 74 mm long with a finger scallop so you can pinch a piece out without emptying the lane. 116 x 99 x 39 mm overall, open underneath to stay light, with two M4 clearance ears (4.5 mm) to screw it to a shelf or bench back.

Soldering Iron Rest And Tip Rack

A 115 x 70 mm bench caddy for a soldering station: twin V-yokes cradle the iron by its handle (notch accepts 8–24 mm grips) at a 25° tip-up angle so the hot tip hangs ~90 mm clear in free air, never touching plastic. Includes a 41 mm ID x 30 mm deep brass-wool cup, four 6.5 mm spare-tip holes plus an 11 mm flux-pen pocket, a 9 mm snap-in cable keeper for the iron lead, and two M4 clearance holes to bolt it to the bench. Print in PETG if your iron runs hot.

80 mm To 60 mm Fan Adapter

A 28 mm tall tapered duct that lets a 60 mm fan feed an 80 mm fan opening (or vice versa): 80 x 80 mm flange with M4 clearance holes on the 71.5 mm pattern at the bottom, 60 x 60 mm face with four 3.4 mm self-tapping M4 bosses on the 50 mm pattern on top. The airway necks smoothly from 73 mm to 55 mm with a 2 mm wall, so it replaces a grinder/zip-tie bodge on amp racks, 3D-printer electronics bays and PC cases.

Raspberry Pi 4 Wall Tray

A 110 x 62 mm vented backplate for a Raspberry Pi 4B / 3B+ with four 5 mm standoffs on the 58 x 49 mm bolt pattern (2.9 mm bores for M2.5 screws), edge stiffening ribs, two keyhole slots that drop over #8 wall screws, an M4 lock hole at the bottom, and a zip-tie bridge for power-cable strain relief. Five long vent slots keep air moving under the board and cut print time.

18650 Four-Cell Pack Jig

A 44 mm square block with four through-bores (18.7 mm, on 20.6 mm centres) that holds four 18650 cells upright, parallel and bottom-flush against the bench so nickel strip lands square during spot-welding or pack glue-up. Open-topped grab notches — one per cell, in 4-fold symmetry — let you spin a cell to set polarity, and two 5 mm ears with M3 clearance holes bolt the jig to the bench; overall 68 x 44 x 26 mm.

2020 Rail Filament Dust Filter

A filament dust and lubrication filter that bolts to a 2020 extrusion rail with two M5 T-nuts (5.5 mm holes, 16 mm apart in one slot) and hangs a 20 mm sponge chamber clear of the rail. Filament drops in through a chamfered funnel mouth, passes a cut sponge cube resting on the internal ledge, and exits a 4.3 mm bore that accepts 4 mm OD PTFE tube. Overall 75 x 26 x 34 mm, gusseted so the tower does not snap off the mounting plate.

18650 Four-Cell Pack Jig

A 44 mm square block with four through-bores (18.7 mm, on 20.6 mm centres) that holds four 18650 cells upright, parallel and bottom-flush against the bench so nickel strip lands square during spot-welding or pack glue-up. Open-topped grab notches — one per cell, in 4-fold symmetry — let you spin a cell to set polarity, and two 5 mm ears with M3 clearance holes bolt the jig to the bench; overall 68 x 44 x 26 mm.

Mini Miter Box Saw Guide

A 120 mm bench-top miter box with guided 90° and left/right 45° saw slots for cutting trim, dowels, and small stock by hand. The channel takes pieces up to 34 mm wide and about 20 mm thick, and two counterbored holes let you screw or clamp it to a bench.

Upside-Down Glue Bottle Stand

A weighted-footprint cup that parks a wood glue bottle nozzle-down so the glue is always primed and never crusts over. The tapered Ø27–35 mm bore self-centers most 8–16 oz caps, with a 12 mm drip well below the tip and two side slots for grip and level checking; 80 mm base, 60 mm tall.

Five-Size Drill Guide Block

A handheld drill guide with five tall bushing towers (3.2, 4.2, 5.2, 6.4 and 8.2 mm) that keep a bit perfectly perpendicular, plus a 90° V-groove underside that self-centers the holes on dowels and round stock. Block is 102 x 36 x 44 mm.

Wrap-Around Hand Sanding Block

A palm-sized sanding block with a flat 88 x 68 mm face and a contoured grip; a quarter sheet of sandpaper wraps the bottom and tucks into the two tapered slots on the end shoulders, which wedge tighter as you sand. Hollow-cored so it stays light and cheap to print.

Right Angle Corner Clamp Jig

An 80 mm L-block that holds two boards at a true 90° while glue sets, with open windows so a spring clamp reaches straight through to the workpiece and a rounded corner relief for squeeze-out. Two 4.5 mm holes let you screw it down to a bench or assembly board.

Round Stock Center Finder

A 90 mm V-jaw layout plate that drops over the end of any round bar, dowel or pipe from about 9 to 70 mm diameter; scribe through the long centre slot, rotate the stock 90° and scribe again — the crossing point is dead centre. The 8 mm deep V lips self-centre the tool so it can't rock off the end face.

6 inch Ruler

A six inch ruler with inset markings.

Sawtooth Jar Lid Wrench

A flat lever wrench whose toothed V-jaw bites any lid from about 21 to 72 mm across, so a stuck jar, bottle or pill cap pops with wrist leverage instead of hand strength. 126 mm long, 9 mm thick, with a hang hole in the handle.

Socket Organizer Rail

A wall or pegboard-mountable rail with eight graduated blind holes (8-16mm) that hold metric sockets by friction, keeping them lined up and visible on a workbench. Overall size 150 x 30 x 14mm with two mounting holes for screws.

Pliers

Print in place articulating pliers

Wedge with ridges

Metric Wrench Set

6mm,7mm,8mm,10mm,12mm,13mm,15mm,17mm

Cable Organizer

Resize for cable thickness.

Simple Wedge

One-Cup Pet Food Scoop

A tapered 1-cup (240 ml) scoop for dog food, birdseed, coffee beans or detergent, with a flat base so it stands on the counter and a 10 mm hole in the angled handle to hang it on a hook. Bowl is 129 mm long with 2.4 mm walls.

Over-Cabinet Door Bag Holder

A U-bracket that slips over a cabinet door (fits panels up to 19.5 mm thick) and turns the inside face into a grocery-bag trash caddy — the bag handles drop into a 9 mm trough behind an upturned lip so they can't slide off. 50 mm wide with two optional screw holes for a permanent mount.

Hot Bowl Microwave Gripper

A hand-held gripper that slides onto the rim of a hot bowl or plate so you can lift it out of the microwave without a towel. The wedge-shaped jaw self-tightens on rims 5.5–8 mm thick, and the 104 mm handle has finger scallops plus a hang hole.

Pasta Portion Measure Paddle

A flat kitchen paddle with four graduated holes that measure dry spaghetti for 1, 2, 3 or 4 servings, plus a ribbed grip and a hanging hole. 141 mm long, 4.5 mm thick, dishwasher-basket friendly.

Herb Stripping Paddle

A flat 150 mm kitchen paddle with seven graduated holes (3–12.5 mm) that strip leaves off rosemary, thyme, kale and chard stems in one pull. Ribbed handle with a hang hole keeps it by the cutting board.

Pot Lid Drip Stand

A countertop tray with a flared twin-rib slot that stands a hot pot lid on edge while the sealed 12 mm-deep basin catches every drip; the rib tops double as a rest for your stirring spoon. Footprint 120 × 90 mm, 32 mm tall ribs, fits lid rims up to 14 mm thick.

Self-Centering Canning Funnel

A 96 mm wide funnel whose 45° cone seat drops into and self-centers on any jar mouth from 46 to 84 mm, so one funnel covers both regular and wide-mouth mason jars. Two side fins give a no-slip grip while you pour rice, beans, or jam; 48 mm tall with 2.2 mm walls.

Sawtooth Jar Lid Wrench

A flat lever wrench whose toothed V-jaw bites any lid from about 21 to 72 mm across, so a stuck jar, bottle or pill cap pops with wrist leverage instead of hand strength. 126 mm long, 9 mm thick, with a hang hole in the handle.

Sink-Side Sponge Caddy

A two-compartment caddy that sits beside the faucet to hold a sponge and scrub brush separately, with slotted drain holes in the bottom so water runs out instead of pooling. Fits a standard sponge; overall footprint 100 x 70 x 45 mm.

Bag Clips

Print in place bag sealing clips

Drink Coozy with Handle

Fits a 12oz can. Grooved handle for grip.

Thumb Page Holder Ring

A one-handed reading aid: slip your thumb through the 22 mm ring and the two 29 mm wings press both page blocks flat so a paperback stays open by itself. Ramped wing tips slide under the pages without creasing them; 80 mm wide overall.

Wall Mail And Key Rack

A 110 mm wall-mounted entryway rack with a 38 mm deep pocket for letters and bills plus three angled hooks with catch lips for keys. Two keyhole slots let it drop onto drywall screws at 88 mm spacing.

Furniture Leg Riser Block

A hollow, rib-cored riser that lifts a bed, couch, desk or dresser leg 44 mm for extra under-furniture storage. The chamfered 58 mm socket accepts square or round legs, and a poke-out hole in the floor frees a stuck leg — order four for one piece of furniture.

Outlet Cover Phone Shelf

A shelf that hangs on the center screw of a standard duplex outlet cover to hold a charging phone off the floor. 70 mm wide plate, 58 mm deep ledge with an 8 mm lip and a cord notch through the middle.

Broom And Mop Wall Gripper

A screw-on wall gripper whose springy C-jaws snap over a 20–26 mm broom, mop, rake or squeegee handle so it hangs off the floor. 60 mm back plate with two counterbored screw holes; 18 mm tall jaws with a 19 mm snap mouth.

Toothpaste Tube Squeezer Key

A winding key that grips the flat tail of a toothpaste or ointment tube in a 3.2 mm slot; twist the finger-hole knobs to roll the tube up and push every last bit out. 96 mm long with a Ø7 mm hang hole in one knob.

Wall Hook

Planter

Two color planter with reliefs

Sticky Note Pad And Pen Dock

A desk dock with a recessed tray sized for a standard 76 x 76 mm sticky note pad and a rounded rear trough for pens, pencils and erasers. A scalloped thumb notch in the front wall lets you peel notes one-handed; footprint is 86 x 113 mm and 20 mm tall.

Nightstand Valet Phone Dock

A 95 x 70 mm catch-all tray with two compartments for keys and coins plus an upright slot that stands a phone (up to 13 mm thick with case) face-up on a raised shelf. A tunnel through the back wall feeds the charging cable up to the phone's port so the cord never leaves the dock.

Clamp-On Headphone Desk Hook

A no-screw C-clamp that slides onto a desk edge or shelf and hangs your headphones underneath on a wide 30 mm saddle. The wedged inner jaw self-tightens on tops from 20–30 mm thick, and the 14 mm hook mouth also takes a bag or lanyard.

Pen Cup With Phone Cradle

A 78 mm-deep pen and pencil cup with a 15°-reclined phone cradle built onto one side, sized for phones up to 13.5 mm thick with a case. A slot through the floor and front lip lets a charging cable reach the port while the phone is docked.

Vertical Laptop Dock

A weighted-footprint cradle that holds a closed laptop, tablet or notebook upright on the desk, with a 22 mm slot, chamfered lead-in edges and a cable pass-through slot in the floor. 90 × 70 × 50 mm.

Slide-Out Stash Box

A print-in-place matchbox-style stash box: a fixed outer sleeve with a drawer that slides in and out to store small items like SD cards, paperclips, or jewelry. Prints fully assembled, ~84 x 44 x 22 mm.

Paint Can Brush Wiper Clip

A curved clip that wedges onto the rim of a 1-gallon paint can, giving you a clean edge to wipe your brush on and a slot to park it over the paint instead of on the rim. Spans a 50° arc of the can, about 74 mm wide.

Upside-Down Glue Bottle Stand

A weighted-footprint cup that parks a wood glue bottle nozzle-down so the glue is always primed and never crusts over. The tapered Ø27–35 mm bore self-centers most 8–16 oz caps, with a 12 mm drip well below the tip and two side slots for grip and level checking; 80 mm base, 60 mm tall.

Utility Blade Disposal Bank

A sealed shop bank that swallows used utility-knife blades, snap-off tips and razor blades through a narrow funneled slot in its peaked roof, so they never end up loose in a drawer or trash bag. 58 x 42 mm footprint, 54 mm tall, holds a few hundred blades before you tape the slot and dispose of the whole thing.

V-Groove Vise Jaw Cap

A slip-on soft jaw cap for a bench vise: the tapered channel wedges onto jaw plates 12.5–16.5 mm thick, and crossed 90° V-grooves cradle round bar either horizontally or standing upright. 80 mm long, 30 mm tall — print two, one for each jaw.

Extension Cord Wall Wrap

A two-horn wall cleat for figure-eight wrapping an extension cord, air hose or rope, with flared post tips that keep the coil from slipping off. 120 mm wide, mounts with two countersunk screws and holds roughly a 50 ft 16-gauge cord.

Stepped Drill Bit Stand

A 147 mm staircase block that stands a 13-piece metric drill index upright, with bores from 1.5 mm to 7.5 mm rising left to right so the size order is obvious at a glance. Each step is taller than the last, so bit tips sit deep and shanks stay easy to grab.

Broom And Mop Wall Gripper

A screw-on wall gripper whose springy C-jaws snap over a 20–26 mm broom, mop, rake or squeegee handle so it hangs off the floor. 60 mm back plate with two counterbored screw holes; 18 mm tall jaws with a 19 mm snap mouth.

Socket Organizer Rail

A wall or pegboard-mountable rail with eight graduated blind holes (8-16mm) that hold metric sockets by friction, keeping them lined up and visible on a workbench. Overall size 150 x 30 x 14mm with two mounting holes for screws.

Heat Shrink Tube Size Rack

A six-lane stadium-step rack that sorts cut heat-shrink tubing by diameter — troughs 8/10/12/14/17/20 mm wide take the common 3:1 sizes from 2.4 mm up to 12.7 mm, each 74 mm long with a finger scallop so you can pinch a piece out without emptying the lane. 116 x 99 x 39 mm overall, open underneath to stay light, with two M4 clearance ears (4.5 mm) to screw it to a shelf or bench back.

M2 To M5 Fastener Sort Tray

A 140 x 85 x 16 mm bench tray with six sloped-floor bins — four 32 x 30 mm pockets for M2/M2.5/M3/M4 screws, nuts and washers, plus two full-length 32 x 62 mm bins for nylon standoffs and longer screws. The front ledge is a screw gauge: four through-holes (2.4 / 3.4 / 4.5 / 5.5 mm) let you drop an unknown fastener through and read off M2, M3, M4 or M5, and every bin floor rises 4 mm toward the back so parts collect at the near edge instead of hiding in a corner.

Metric Hex Key Wall Rack

Wall rack that stands a nine-piece metric hex key set upright in graduated hexagonal sockets (1.5, 2, 2.5, 3, 4, 5, 6, 8, 10 mm across flats, 12 mm deep) so sizes read left to right and nothing rolls loose in a drawer. Roughly 92 x 28 x 34 mm, mounts with two M4 screws through 4.5 mm clearance holes in the 4 mm back plate, with a full-length 35° buttress carrying the shelf load into the wall instead of across layer lines.

One-Cup Pet Food Scoop

A tapered 1-cup (240 ml) scoop for dog food, birdseed, coffee beans or detergent, with a flat base so it stands on the counter and a 10 mm hole in the angled handle to hang it on a hook. Bowl is 129 mm long with 2.4 mm walls.

Over-Cabinet Door Bag Holder

A U-bracket that slips over a cabinet door (fits panels up to 19.5 mm thick) and turns the inside face into a grocery-bag trash caddy — the bag handles drop into a 9 mm trough behind an upturned lip so they can't slide off. 50 mm wide with two optional screw holes for a permanent mount.

Wall Mail And Key Rack

A 110 mm wall-mounted entryway rack with a 38 mm deep pocket for letters and bills plus three angled hooks with catch lips for keys. Two keyhole slots let it drop onto drywall screws at 88 mm spacing.

Furniture Leg Riser Block

A hollow, rib-cored riser that lifts a bed, couch, desk or dresser leg 44 mm for extra under-furniture storage. The chamfered 58 mm socket accepts square or round legs, and a poke-out hole in the floor frees a stuck leg — order four for one piece of furniture.

Cotton Round And Swab Dispenser

A countertop vanity dispenser: a 61 mm tube that stacks standard cotton rounds with a full-height front slot so you can see the level and pull one out with a thumb, plus an attached 28 mm cup for cotton swabs. Footprint 98 x 66 mm, 82 mm tall.

Three-Tier Spice Step Riser

A three-step cabinet riser that stair-steps spice jars so every label is visible from the front. 80 mm wide x 108 mm deep x 66 mm tall, with a 3 mm lip on each tread so jars can't slide off; hollow open-bottom shell with internal ribs to keep it light.

Clamp-On Headphone Desk Hook

A no-screw C-clamp that slides onto a desk edge or shelf and hangs your headphones underneath on a wide 30 mm saddle. The wedged inner jaw self-tightens on tops from 20–30 mm thick, and the 14 mm hook mouth also takes a bag or lanyard.

Pen Cup With Phone Cradle

A 78 mm-deep pen and pencil cup with a 15°-reclined phone cradle built onto one side, sized for phones up to 13.5 mm thick with a case. A slot through the floor and front lip lets a charging cable reach the port while the phone is docked.

AA AAA Battery Dispenser

A gravity-fed dual-channel dispenser that stacks 6 AA and 8 AAA cells and drops the next one into a front grab window with a retaining lip. Stands 92 mm tall on a shelf or screws to a wall through the two rear ears.

Broom And Mop Wall Gripper

A screw-on wall gripper whose springy C-jaws snap over a 20–26 mm broom, mop, rake or squeegee handle so it hangs off the floor. 60 mm back plate with two counterbored screw holes; 18 mm tall jaws with a 19 mm snap mouth.

Toothpaste Tube Squeezer Key

A winding key that grips the flat tail of a toothpaste or ointment tube in a 3.2 mm slot; twist the finger-hole knobs to roll the tube up and push every last bit out. 96 mm long with a Ø7 mm hang hole in one knob.

Slide-Out Stash Box

A print-in-place matchbox-style stash box: a fixed outer sleeve with a drawer that slides in and out to store small items like SD cards, paperclips, or jewelry. Prints fully assembled, ~84 x 44 x 22 mm.

Socket Organizer Rail

A wall or pegboard-mountable rail with eight graduated blind holes (8-16mm) that hold metric sockets by friction, keeping them lined up and visible on a workbench. Overall size 150 x 30 x 14mm with two mounting holes for screws.

Sink-Side Sponge Caddy

A two-compartment caddy that sits beside the faucet to hold a sponge and scrub brush separately, with slotted drain holes in the bottom so water runs out instead of pooling. Fits a standard sponge; overall footprint 100 x 70 x 45 mm.

Wall-Mount Hair Dryer Holster

A screw-mounted holster that holds a hair dryer by its barrel in a 64 mm ring so the handle and cord hang clear of the counter. Plate is 62 x 62 mm with two 4.6 mm screw holes on 40 mm centers; the ring stands off the wall 36 mm.

Cotton Round And Swab Dispenser

A countertop vanity dispenser: a 61 mm tube that stacks standard cotton rounds with a full-height front slot so you can see the level and pull one out with a thumb, plus an attached 28 mm cup for cotton swabs. Footprint 98 x 66 mm, 82 mm tall.

Draining Toothbrush Wall Rack

A 100 mm wide wall rack that hangs four toothbrushes head-up in open keyhole slots so they drain and air-dry instead of sitting in a wet cup. Slots take handles from the top edge, and four screw holes mount it to drywall or tile.

Draining Bar Soap Dish

A 100 x 72 mm bar-soap dish with a 3 mm sloped floor, five lengthwise ribs that keep the bar up out of the water, and a spout notch with a flat drip tongue that sends runoff into the sink instead of onto the counter.

Toothpaste Tube Squeezer Key

A winding key that grips the flat tail of a toothpaste or ointment tube in a 3.2 mm slot; twist the finger-hole knobs to roll the tube up and push every last bit out. 96 mm long with a Ø7 mm hang hole in one knob.

Triple Gear Crank Fidget

A 144 mm desk plate with three real meshing gears — a 24-tooth crank wheel with a domed finger knob driving two 14-tooth pinions, all captured on mushroom-cap posts. Prints fully assembled, no supports: four separate pieces, 0.45 mm clearance everywhere, spin the knob and the whole train turns.

Wiggle-Leg Flexi Centipede

A 139 mm print-in-place centipede: eight leg-bearing body segments joined by seven captured ball-and-socket joints, so the whole body ripples and curls in your hand. Prints fully assembled, flat on the plate, no supports and no assembly.

Print-In-Place Slide Bolt Latch

A working barrel-bolt latch that prints fully assembled — the red bolt slides inside the grey housing with 0.4 mm clearance, no assembly and no supports. 76 mm housing with four screw ears; the bolt throws 27 mm past the end to catch a cabinet, shed door, gate, or toy box.

Print-In-Place Turntable Caddy

A 100 mm lazy-susan tray that prints as one piece and spins straight off the plate — the deck is captured by a mushroom post and rides on low-friction ring lands. Holds spice jars, sauces, pens or craft supplies in a 90 mm bowl with a 10 mm rim and eight grip ribs.

Snap-Gate Carabiner Clip

A 60 mm one-piece carabiner whose gate is a built-in flexing spring arm — press it inward to hook on, and a capture nose stops it opening under load. Prints flat with no supports, no assembly, and no metal spring; sized for keys, water bottles, and bag straps.

Slide-Out Stash Box

A print-in-place matchbox-style stash box: a fixed outer sleeve with a drawer that slides in and out to store small items like SD cards, paperclips, or jewelry. Prints fully assembled, ~84 x 44 x 22 mm.

Patio Umbrella Hole Wobble Shim

A tapered split collar that drops into an oversized patio-table umbrella hole and wedges the pole tight so it stops rattling and leaning. Suits ~38 mm poles in 44–52 mm table holes; 68 mm flange rests on the tabletop.

Bottle Plant Watering Spike

A soil spike that turns an empty soda bottle into a slow-drip plant waterer — press the inverted bottle neck into the ribbed socket and push the 140 mm spike into the pot. Three staggered drip ports feed water down at the root zone while the 44 mm flange keeps it from sinking.

Beach And Lawn Drink Spike

A ground stake with a tapered funnel socket that grips 12 oz cans, bottles and tapered party cups so drinks stay upright in sand, grass or dirt. 148 mm tall with four grip ribs at the rim for pushing it in by hand.

Step-On Boot Jack

A stand-on jack that pulls muddy boots off without touching them: the heel drops into a tapered 20–55 mm V while your other foot holds down the slotted deck. 135 × 60 × 32 mm, prints flat with no supports.

Garden Twine Dispenser Can

An open-top can that swallows a ball of jute or sisal twine (80 mm inner diameter, 80 mm deep) and feeds it out through a guide eyelet, with a pinch slot on the lip that grips the loose end so it never falls back inside. A keyhole on the flat back hangs it on a single screw in the shed or potting bench, or it just sits upright on the bench.

USA 250 Keychain