Heads up: many models on this page are AI-generated or uploaded untested. They may be misconfigured for the intended application — check the dimensions and tolerances, and verify or edit the model before printing or relying on it.*
Five-Size Roll Pin Punch V-Guide
This V-block guide keeps a pin punch square to a round shaft while you drive out a roll pin, for example when replacing a stripped garage-door-opener gear, a worn blender coupler or a sheared pin in a crank. It is 120 x 28 x 30 mm. The 90° V-groove fits 5–30 mm shafts, and five slip-fit bores for 3, 4, 5, 6 and 8 mm punches all sit on the V's centre plane, so whichever bore you use lines up over the shaft's cross-hole. A zip-tie tunnel at each end straps the guide to the shaft.
Five-Size Starlock Washer Push-On Installer
A 150 x 30 x 18 mm pusher bar for seating push-on starlock retaining washers squarely on 3, 4, 5, 6 and 8 mm shafts, axles and pins. These are the clips on dryer drum rollers, fan blades, toy and mower axles. Each boss has a blind bore (3.4 / 4.5 / 5.3 / 6.3 / 8.3 mm, 15.5 mm deep) that the shaft end slides into, plus a 1.2 mm relief ring so only the washer's flat body gets pressed and the teeth don't get crushed. Dimples from one to five mark the sizes.
Twin-Fork Appliance Knob Lift Lever
A 150 mm double-ended lever with a raised fulcrum heel. It lifts stuck push-on dial knobs off air fryer, toaster oven and stove shafts with an even upward pull, so they don't crack where the shaft enters. One end has a 7 mm slot fork for 6 mm D-shafts and the other a 10.5 mm fork for larger stems. The tines taper from 2.6 to 1.4 mm so they slip under knob skirts, and the 8 mm heel rests on the panel as the pivot.
Three-Pivot Dehumidifier Float Lever
This replaces the cracked float arm in a dehumidifier bucket. A broken arm stops the unit from running even when it still works. The lever is 162 mm long with a sealed hollow float (40 x 24 x 14 mm, about 13 g of lift). It has three 3.4 mm pivot holes 10 mm apart that take a 3 mm steel pin or an M3 screw, so you can choose the lever ratio, and a 12 mm tall switch flag you can trim to the length you need.
Chest Freezer Basket Hanger Bracket
A replacement end hanger for a chest freezer wire basket. Its 6 mm wide cradle holds the basket's top rail wire (anything up to about 5.5 mm thick) and is locked on with two zip-tie slots that take ties up to 4.8 mm wide. A 35 mm foot with a stop lip sits on the freezer's inner ledge and holds the basket about 45 mm below it, so a basket with a snapped hanger works again without buying a whole new basket. The part is 45 x 56 x 20 mm and prints flat, so the basket's weight bends it along the layers instead of pulling them apart.
Slotted-Span Fridge Door Pull Handle
A 170 mm replacement pull handle for a refrigerator or freezer with a cracked or snapped handle. The two feet have 10 mm slots for M4 or #8 screws, so it fits screw spacings anywhere from 136 to 156 mm without drilling new holes. The bar stands 26 mm off the door to leave room for your fingers, and the screw heads sit in 9 mm counterbore channels you reach from the front. It prints flat, so the pulling force runs along the layers instead of across them.
Six-Module Gear Tooth Rack Gauge
This 130 x 50 x 3 mm card identifies the module of a stripped gear so you can model a replacement. Its two long edges carry 20° rack combs for modules 1, 1.25 and 1.5 (top) and 2, 2.5 and 3 (bottom), and you press each comb into the old gear until one meshes with no rock. The number of small holes beside each comb gives its module: 1 hole = m1, up to 6 holes = m3. Built for fan oscillator, mixer and blender gears. m1.25, m1.5 and m2.5 are close to 20, 16 and 10 DP.
150 mm Microwave Turntable Roller Ring
Replacement microwave turntable support ring for ovens whose glass tray rides on a 150 mm roller track. It has three 18 mm rollers on radial pins, a 168 mm OD ring and a loose 36 mm hub that drops over drive couplers up to about 34 mm. The ring, rollers and pins are all PLA with no metal inside. They print together on breakaway sprues: snap them off, drop each roller between its cheeks and push the headed 4 mm pin through, where the inner cheek grips it. The tray sits 18 mm above the floor and the ring clears it by 2.5 mm.
Universal Toaster Lever Slide-On Knob
This knob replaces a broken toaster lever knob. It is 36 x 26 x 18 mm, with a cross-shaped socket that takes a flat steel lever tab up to 12.5 x 3 mm or a round stem up to 6 mm, and an M3 heat-set insert and grub screw clamp it to whichever one your toaster has. OEM lever knobs are usually discontinued, and this one means you don't have to throw out a working toaster over a snapped piece of plastic.
Washer Anti-Walk Leveling Foot Cup
A low, wide cup that sits under a washing machine or dryer foot. It holds any round leveling-foot pad up to 55 mm across in a 14 mm deep centring dish with grip ribs, and spreads the load over an 84 mm footprint, so a machine with a worn or cracked OEM foot stops walking across the floor during the spin cycle. The outside has a 45° ramp so the foot can be levered in, and the cup works with any foot thread because it never touches the thread.
Fridge Door Hinge Pin Socket Plate
A screw-on repair plate that gives a sagging refrigerator or freezer door a fresh hinge-pin socket when the moulded nylon pocket has worn oval. The 72 x 52 x 5 mm plate carries a ribbed 22 mm boss with an 8.3 mm slip-fit socket 12 mm deep for a standard 8 mm hinge pin, a 22 mm x 2 mm relief recess underneath so it sits flat over the chewed-up original boss, and four 4.5 mm holes on a 56 x 38 mm pattern for #8 screws or M4 bolts.
Washer Dryer Door Catch Receiver
A universal cabinet-side door catch for front-load washers and dryers whose original plastic striker receiver has cracked: two long compliant jaws with rolled pinch ribs grab the door's striker prong (5–8 mm thick, up to 8.6 mm wide at the funnel mouth) and a 2.6 mm M3 self-tapping set screw in the back wall sets seating depth so the door seal compresses right. 76 x 56 x 22 mm with a 5 mm mounting plate — one 4.5 mm M4 clearance hole and one 12.5 mm slot on 58 mm centres so it aligns to existing cabinet screws; print in ASA, ABS or PC-blend if it goes on a dryer.