Heads up: many models on this page are AI-generated or uploaded untested. They may be misconfigured for the intended application — check the dimensions and tolerances, and verify or edit the model before printing or relying on it.*
Slotted Triangular Desk Credenza Foot
This is a 75 mm tall tapered triangular foot that screws onto desk credenzas, desk pedestals, media consoles and TV stands. It replaces a mid-century-style foot that has snapped off and is no longer sold. The 94 mm triangular flange has three radial slots, 4.8 mm wide by 7 mm long, for #8 (4.2 mm) wood screws, so it can line up with old pilot holes. The hollow 2.5 mm-wall leg narrows from a 48 mm to a 35 mm triangle and ends in a 16 mm × 2 mm recess for a stick-on felt or rubber bumper.
Three-Screw Self-Centring BBQ Grill Knob
A universal replacement burner knob for gas grills where the original has cracked in the sun. It is 55 mm across and 34 mm tall, with a pointer fin on the front. It has a 9 mm stem bore and three M4 set screws at 120° in M4 heat-set inserts (5.5 mm bores), so it centres itself on round or D-flat valve stems from about 5 to 8 mm instead of needing one exact OEM fit. Holes in the skirt give a soldering iron and hex key access and let rain drain out. Print it in PETG or ASA for outdoor heat and UV.
Washer-To-Dryer Stacking Foot Cup
A cheaper replacement for the OEM stacking kit: four of these cups go on top of a front-load washer, and each dryer leveling foot drops into a tapered cup (36 mm at the floor, 44 mm at the 12 mm rim), which fits any foot from about 25 to 42 mm across. Each 100 x 60 x 3 mm plate fixes down with two #8 sheet-metal screws through 4.6 mm slots and has a 27 x 4 mm slot for a 25 mm anti-tip strap. The cup walls stop the dryer from walking off the washer.
Tool Case Print-Aligned Hinge With 4 mm Pin
A 60 mm five-knuckle replacement hinge for stackable tool cases and toolbox lids whose moulded plastic hinge has snapped. The two 21 x 3 mm leaves print flat in one go with their knuckles already lined up. Afterwards you tap in a 60 mm length of 4 mm steel rod: the leaf with three knuckles grips the rod, and the other leaf swings on it. Each leaf has three M4 / #8 slots on a 20 mm pitch, with ±3 mm of play so they can line up with the old holes.
Tarp Bungee Ball Knot-Pocket Replacement
A replacement for the hard ball on a tarp ball-bungee: a 32 mm dome with two parallel 6.5 mm bores that take a 4–6 mm shock cord loop, a recessed pocket on top so the end knots sit flush, and a 45° V-groove around the middle where the loop hooks back over. It's 32 mm across and 25 mm tall, prints without supports, and replaces the balls that crack or go missing on truck-bed, trailer and firewood tarps.
Garage Door Slotted D-Pull Lift Handle
A heavy D-pull lift handle that replaces a cracked plastic garage door handle or step plate. It's 150 mm long and 50 mm deep, with a 64 x 34 mm opening wide enough for gloved fingers. It mounts with two #10 (4.8 mm) pan-head screws through 5.3 mm slots, so the hole spacing can be anywhere from 100 to 124 mm. The slots let you shift each screw to land on a door stile or rib. It prints on its side, so the pull load runs along the layers, and gussets reinforce each corner.
Shower Tray M5 Jack-Bolt Leveling Foot
This is a single replacement leveling foot for a low-profile shower tray. You don't need to buy a whole new leg kit to fix one cracked corner. It's a 60 mm floor pad with a 26 mm ribbed column 30 mm tall. Inside the column is a captured M5 hex nut (8 mm across flats, slides in from the side). Thread any M5 bolt down through it and turn it to jack the tray up under the cracked foot.
Toilet Tank Rim-Hang Water Saver Bank
A cup that hangs inside a toilet tank and stays full while the tank empties, so each flush uses about 0.35 L less water. Its 2 mm bar sits on the tank rim under the lid, and an 18 mm hook gap fits tank walls up to about 17 mm thick. The 150 x 50 x 70 mm cup has a 45° end wall to clear the flapper. It hangs on an 80 mm drop, so its open top sits 80 mm below the rim and fills on every refill. Measure your fill line before printing: it has to be less than 80 mm below the rim.
Monitor Arm Zip-Tie Cable Saddle
A 34 x 30 x 36 mm cable saddle that replaces the snap-on cable covers that break off monitor arms. A 90° V-notch underneath sits on round arm tubes about 18–50 mm across or on flat-topped arms, and two 2.2 x 5.5 mm tunnels take standard zip ties up to 4.8 mm wide to strap it down. On top there are three snap-in channels: one 8.2 mm bore for an HDMI or DisplayPort cable and two 6.2 mm bores for USB-C or power leads, each with a mouth 1.2 mm narrower than its bore so the cable clicks in.
Slot-Adjust Print-In-Place Surface Cabinet Hinge
This surface-mount butterfly hinge prints in place. Each 64 x 28 x 3 mm leaf has a 9 mm five-knuckle barrel with a 5 mm pin running in a 6 mm bore, so the pin has 0.5 mm of clearance all round. It replaces discontinued non-Euro hinges on older face-frame cabinets. The 3.8 mm slots for #6 wood screws (3.5 mm shank) run lengthwise on one leaf and crosswise on the other, so you can line them up with the old screw holes instead of drilling new ones.
Sliding Screen Door Slotted Pull Plate
Replacement pull for sliding patio screen doors whose Prime-Line / Slide-Co style mortise handle is discontinued: a 40 x 150 x 3 mm cover plate hides the old mortise pocket (up to 28 x 70 mm) and carries a 70 mm long, 26 mm tall 45-degree hooked grip. Two 4.5 x 24 mm vertical slots take the original 8-32 or M4 through-bolts at any hole spacing from 80 to 128 mm (3-1/8 to 5 in); print two and bolt them back-to-back through the door stile for an inside and outside pull.
Office Chair Caster Stem Glide Foot
Fixed glide foot that drops into an office chair base in place of a rolling caster, for the standard 7/16 in x 7/8 in (11 x 22 mm) grip-ring stem socket; the 10.2 mm stem carries four crush ribs to 11.4 mm so it presses tight into 11.0–11.3 mm sockets (not 10 mm Euro stems). The 50 mm diameter, 14 mm tall pocketed foot has a flat bottom for a stick-on felt pad and a 36 mm overall height; print five to stop a chair rolling on hard floors.
Pilaster Shelf Clip Four-Width Sprue
Snap-off sprue of 16 hook-style shelf clips for slotted steel pilaster standards in bookcases, closets and store shelving, four clips each in 3.4, 4.0, 4.6 and 5.2 mm prong widths so you can match a slot the shops no longer stock (pick the column 0.2 to 0.3 mm under your measured slot width). Each clip is a single top hook (1.8 mm thick, 1.5 mm crook for steel up to 1.4 mm, needs a slot at least 6 mm long and 3.5 mm of cavity behind the strip) over a 16 mm bearing pad, with a 14 mm gusseted ledge and 2 mm front lip; it works on any slot pitch, and in PETG expect roughly 5 kg per clip, about a quarter of the steel originals.
1 in Wire Shelf Post Split Sleeve Pair
Replacement wedge-collar sleeve pair for 1 in (25.4 mm) wire-shelving posts (Metro, HDX, Whalen/Costco, Seville style), printed upright and joined by two snap-off tabs. Bore is 25.6 mm with a 2.6 mm wide, 0.8 mm deep internal rib 15 mm above the base that drops into the post groove; the outer taper runs 28.8 mm at the small end to 34 mm at the top over 46 mm, so any shelf collar whose bottom opening passes 28.8 mm wedges and locks as it slides down. Print one pair per post position (four pairs per shelf) to re-hang a shelf whose original clips cracked or went missing.
Window Screen Push-In Pull Tab Set
A set of four replacement window screen pull tabs that push into the spline channel beside the rubber spline, replacing the vinyl tabs that crumble in the sun. Each tab is a 10 mm wide finger loop (15 mm outer diameter, 9.5 mm hole) on a 12 x 2.4 mm base that sits on the frame lips, with a 1.2 mm thick barbed leg in four lengths (5, 7, 9 and 11 mm) to suit shallow and deep channels around a 3.6 mm spline; the whole set prints flat on its side so layer lines run along the loop-to-leg bend and the tabs snap apart on 1 mm thick sprues.
Snap-Off PC And Console Foot Set
This is a set of four tapered 34 mm feet, 12 mm tall, joined by thin snap-off bridges. They replace the lost feet on PC towers, consoles, amplifiers and project boxes, and lift the case back up off the desk so the vents can breathe. Each foot fastens with an M3 screw through a 3.4 mm clearance hole. The screw head sits in a 6.5 mm counterbore under a 14 mm × 2 mm recess, where you can stick a rubber bumper. The top face is flat, so you can also use VHB tape if there's no screw boss.
Through-Glass Shower Door Knob M5
A replacement shower door knob, 40 mm across and 35 mm tall. Print two and join them through the glass with a length of M5 threaded rod. Each knob has an M5 hex nut pocket (8.3 mm across flats), a 22 mm deep M5 clearance bore and a 25 mm × 2.2 mm recess on the glass face for a rubber washer. It fits 6–10 mm glass with any hole of 6 mm or larger, so you can replace a cracked plastic knob without tracking down the original part.
Three-Cell Draining Cutlery Caddy
This is a freestanding cutlery basket to replace the one that cracked or went missing from a dish rack. It measures 100 x 70 x 100 mm and has three 31 mm cells for forks, knives and spoons. Water drains through 5 mm holes in the floor into four underfloor channels that open out both sides, and vertical slots in the front and back walls let air through so the cutlery dries instead of sitting in a puddle.
Flex-Fin Chain-Link Post Cap 57-63 mm
This rain cap replaces a missing or rusted cap on a 2-3/8 in (60.3 mm OD) chain-link terminal post or a 60 mm metric round post. Eight angled flex fins grip any post from 57 to 63 mm OD, so an odd-size or out-of-round tube still gets a snug cap. The cap is 76 mm across with a drip lip and a 32 mm skirt. A 4.5 mm side hole takes a #8 self-drilling screw to lock the cap in place against wind and theft.
Screw-On Pocket Door Edge D-Pull
This is a D-loop pull that screws onto the leading edge of a pocket door, so you can grab a door that has slid all the way into the wall. It is 90 x 28 x 26 mm and has two countersunk 4.6 mm holes for #8 (4.2 mm) wood screws or M4 screws. The 26 mm wide base fits 1-3/8 in (35 mm) and 1-1/8 in (28.6 mm) interior door edges, and the 52 x 17 mm finger opening fits fingers of any size. It prints on its side so your pull goes across the layers, not against them.
Chainsaw Bar Nose Scabbard
A slip-on scabbard for the tip of a chainsaw bar. It covers the front 128 mm of a 14–18 in bar that stands up to 76 mm tall with the chain on. The channel inside is 12 mm wide, and crush ribs grip the cutters, so it also fits 0.325 in and 3/8 in chain kerfs. A 5 mm cord eyelet lets you tie it to the saw's handle. It replaces a lost or cracked OEM bar cover for storage and transport.
Hose Reel Spinning Crank Knob M5
This print-in-place crank knob replaces the snapped handle on a wall-mount or cart garden hose reel. The 29 mm grip spins freely on a core that is 66 mm tall. It bolts through the reel's existing crank arm with one M5 bolt. The bolt head sits deep in a 9.6 mm socket, so an M5 x 25–30 mm bolt is long enough. A captured M5 nut pocket (8.2 mm across flats) in the 30 mm base flange lets you run the bolt from either side. It isn't tied to any brand's handle shape, so a reel that still works can go back into service.
Double-Prong Bathroom Robe Hook
A two-prong robe and towel hook for the back of a bathroom door or wall. It replaces a snapped zinc hook without having to find the brand's hidden-mount base. It is 91 x 60 x 20 mm, and the 80 mm back plate mounts with two countersunk #8 wood screws (4.2 mm shank) through 4.6 mm clearance holes 40 mm apart. The long upper prong reaches 60 mm from the wall and the short lower one 42 mm. Both have ball tips so fabric won't snag.
608 Bearing Clothesline Pulley Wheel
A 70 mm replacement pulley wheel for old clothesline brackets whose original wheel has seized or cracked. The bracket stays where it is. A 608 bearing (8 x 22 x 7 mm) press-fits into a 22.05 mm pocket and runs on an 8 mm (M8 or 5/16 in) axle bolt. The wheel is 15 mm thick at the hub, so it fits any fork with at least 16 mm between the cheeks; washers take up any extra width. The 90° V-groove, 5 mm deep, holds clothesline up to about 6 mm thick.