Heads up: many models on this page are AI-generated or uploaded untested. They may be misconfigured for the intended application — check the dimensions and tolerances, and verify or edit the model before printing or relying on it.*
Octagon Push-On File Handle
A 110 mm anti-roll octagonal handle for bare-tang hand files and rasps. It has a three-step tang socket (8, 6 and 4.5 mm, 50 mm deep in total) so one handle fits small and mid-size tapered tangs. Push the file in, or warm the tang to seat it. A 5.5 mm hang hole through the pommel lets it hang on a pegboard hook or nail.
Lever Wedge Staple Remover
This is a 100 x 22 x 8 mm lever-style staple remover. Its blade tapers over 32 mm down to a 12 mm wide, 1.2 mm thick tip. You slide the tip under a standard office staple crown and rock it up, so you don't need the spring-jaw "biter" that tears pages. It has a thumb dimple for leverage and a 6 mm hang hole so it can sit on a pegboard or on a key ring next to the stapler.
Set-Screw V-Socket Hand Tap T-Wrench
A 120 mm T-handle tap wrench. The tap shank sits in a through-socket shaped as a 7 mm square turned 45°, and an M5 set screw running through a captured M5 nut pushes it into the V corner, so it grips round or square shanks from about 2.5 mm to 7 mm (small taps, reamers, screw extractors). It replaces the tap wrench that went missing from a cheap tap-and-die set, and the twist load stays flat in the print plane so it doesn't pull the layers apart.
Trampoline Spring Puller T-Handle
A solid T-handle spring puller for fitting or replacing trampoline springs and mats. It has a 100 × 22 mm palm grip and a 96 mm shank that ends in a J-hook. The hook slot is 6.5 mm wide with a 10 mm deep catch pocket, which holds the wire end hook of a spring so the tool doesn't slip off the way the stamped-steel ones do. It prints flat, so the pulling load runs along the layers instead of across them.
Sheet Metal Hand Folding Bar
A hand folding bar for putting clean flanges and hems in thin sheet: clamp the work in a vise with the bend line at the jaw, drop the bar over the protruding edge and lift the U-handle. The 126 mm bar carries two full-length slots — 2.4 mm wide x 12 mm deep for 0.5-2 mm aluminium flashing, brass or copper, and 4.2 mm wide x 10 mm deep for HDPE/PP sheet and soft aluminium strip — both with flared 18-degree entries so the sheet finds the slot one-handed. Slots sit on one side of the bar, leaving a 10.7 mm solid spine that takes the handle torque; overall 126 x 70 x 16 mm with 45-degree gussets at the arm roots.
Flagged: hydraulic brake system. Not for safety-critical use without independent engineering review.
Hacksaw Blade Jab Saw Handle
A one-piece handle that turns a snapped 12.5 mm hacksaw blade into a jab saw for cutting in tight spots — 148 mm long with a 1.6 mm x 13.5 mm blade slot 55 mm deep, so the blade bottoms out on a solid end stop for push cuts. Two M4 brass heat-set inserts (5.5 mm bores) take M4 set screws that pinch the blade against the far slot wall; the grip is 22 x 26 mm with finger scallops, a hollow ribbed core, and an 8 mm hanging hole for a pegboard hook.
Flagged: a sharp edge or blade. Not for safety-critical use without independent engineering review.
Tub And Tile Caulk Tool
A one-piece 100 x 50 x 10 mm caulk finishing and removal tool for re-sealing a tub, shower pan or vanity backsplash: its four working corners are rounded to 5, 8, 12 and 16 mm so each one lays a matching concave silicone fillet while the two adjacent flats ride the walls of the 90° joint. The opposite side carries a 26 mm wide scraper blade tapered to a 1.8 mm plastic-razor edge for lifting old silicone off tile without scratching it, a narrow rake point for digging the joint out, and a 4.5 mm hole for an M4 screw or nail to hang it.