Heads up: many models on this page are AI-generated or uploaded untested. They may be misconfigured for the intended application — check the dimensions and tolerances, and verify or edit the model before printing or relying on it.*
M5 Bolt-Pivot Fan-Out Sort Tray Tier
A four-cell parts tray (126 x 64 x 22 mm) with a 20 mm pivot boss bored to 5.5 mm. Stack several on one M5 bolt and they fan out sideways like a tackle-box tower, so the cells you aren't using swing back out of the way. Each boss is 24 mm tall, which leaves a 2 mm gap between tray tiers. The whole stack bolts through to a bench or under a shelf, and you set the swing friction by how tight you run the M5 nut.
Screw Counting Tray With Pour Spout Channel
This is a pharmacy-style counting tray for loose screws, nuts and small hardware. It has a 116 x 56 mm counting area and a 45° ramp up to a divider 8 mm above the floor. Tens slide over the divider into a 16 mm side channel, and a tapered spout pours them straight into a bag or jar. The rest tips back out of the open tray. Overall it is 142 x 80 x 20 mm with 2 mm walls and floor.
2020 Extrusion Bolt-On Three-Cell Parts Bin
A 120 x 55 mm three-cell scoop bin that bolts to the side of any 2020 aluminium extrusion workbench, test rig or robot frame using two M5 bolts and T-nuts (5.5 mm clearance holes, 80 mm apart). A 5.6 mm locating rib drops into the 6 mm T-slot so the bin stays level. The sloped 45 mm-to-30 mm rim and 45° scoop ramps let you sweep screws out with a fingertip. It keeps small fasteners on the frame, right where you're working, instead of loose on the bench.
Five-Peg Compression Spring Sort Tray
A 150 x 80 mm tray for a loose spring assortment. Five 50 mm pegs at 4, 5, 6, 8 and 10 mm diameter hold compression springs stacked by inner diameter, and each peg doubles as an ID gauge: a spring goes on the largest peg it will slide over. The pegs sit in walled cells marked with 1 to 5 floor dots, and a full-width back trough holds extension and torsion springs.
Gridfinity 1x1 Four-Cell Half-Grid Bin
A standard Gridfinity 1x1 bin (41.5 x 41.5 mm, 3 units / 21 mm tall, no stacking lip) split into four 18 x 18 mm cells on a 21 mm half-grid pitch. Each cell has a 45° scoop ramp at the front. It gives desk and bench Gridfinity grids the finer sorting that SMD parts, small screws and connectors need, without moving to a non-standard baseplate.
Stepped Radial Capacitor 12-Cell Sort Tray
A 150 x 105 mm tray with 12 cells in three tiers. Walls stand 22, 32 and 42 mm tall, giving pockets 20, 30 and 40 mm deep, each about 35 x 33 mm. The tall cells hold radial electrolytic caps (5x11 mm up to 13x25 mm), legs and all, which won't fit in shallow resistor trays. Every cell has a 45° scoop ramp at the front so you can slide parts out with a finger, and the vertical step faces on the two back tiers take value labels.
608 Stacking Hardware Carousel Tier
A spinning parts tray, 150 mm across, with six 20 mm deep wedge bins. A 608 bearing (8 x 22 x 7 mm) press-fits into a 22.05 mm pocket underneath, so you can stack several tiers on one 8 mm rod or M8 threaded rod, each held up by an M8 nut under the bearing's inner race. It gives you a lazy-susan screw sorter that keeps all your sorted fasteners on one small spot of the bench.
Pinch-Bolt 1/2 in EMT Rail Parts Bin
A 90 x 60 x 50 mm open parts bin with a 45° V-roof hook that hangs over a 1/2 in EMT conduit rail (17.9 mm OD) above a bench. One M4 x 35 bolt goes through 4.5 mm holes in the bin's rear pillar and the flexing back leg and pinches the rail, so the bin can't rock forward when it's loaded and you can slide it anywhere along the rail. The rail needs at least 25 mm of wall standoff to clear the 3 mm back leg.
NEMA 17 Three-Motor Storage Tray
A 146 x 62 x 12 mm bench or drawer tray that holds three spare NEMA 17 steppers upright on their backs, each in a 43.3 mm square pocket that fits the 42.3 mm motor body. The shafts stay pointing up and out of the way. A 24 mm push-up hole under each motor and finger notches in the walls make them easy to lift out, and a 9.5 mm trough along the front holds the M3 screws, pulleys and couplers that go with them.
2020 Extrusion Offcut Rack With T-Nut Trough
This bench rack has eight 20.9 mm square sockets that hold 2020 aluminium extrusion offcuts upright. Next to the sockets is a 94 x 20 mm open trough for M5 T-nuts and screws. Each socket has a 10 mm push-out hole in the floor, and the rack screws to a bench through two M4 clearance holes. Overall size is 100 x 75 x 30 mm.
Micro Servo And Horn Sorting Caddy
A 137 x 70 x 18 mm drawer caddy for spare servos. It has ten 25 x 14 mm upright pockets, 16.4 mm deep, sized for 9 g micro servos (SG90 / MG90S class, body about 23 x 12.5 mm): each servo stands with its mounting tabs on the rim and its lead hanging over the edge. Along the front are three 43 x 32 mm scooped bins for loose horns, horn screws and spline adapters.
M3 M4 M5 Captive-Nut Thread Checker
This 84 x 30 x 17 mm bench block holds real steel M3, M4 and M5 hex nuts (5.5, 7 and 8 mm across flats), which slide into side-loaded traps. To check an unmarked bolt, thread it in and see which size it fits. That saves you from trying the bolt in loose nuts over and over. Each station has a 3.4, 4.5 or 5.5 mm clearance bore. A relief channel underneath lets long bolts run out the bottom. Rows of 3, 4 and 5 dimples mark the sizes.
Locking-Peg Pegboard Small Bin
A two-column open-top parts bin, 50.0 W x 65 D x 70 H, that is part of the '1/4 in Pegboard Locking-Peg Tool Wall' kit. It hangs on two of the kit's printed octagonal hook pegs and is held by two split, ridged lock pins in standard 1/4 in pegboard (6.35 mm holes on a 25.4 mm grid). The 5 mm back plate has 5.8 mm octagon sockets at X ±12.7 mm, with the hook row at Z 62 and the lock row 25.4 mm below it, so a bump won't lift the bin off the board.
Wide Twin-Hanger Cleat Bin
This wide open-top scoop bin is part of the 'Printed French Cleat Bin Wall' kit. It measures 160 x 100 mm and is 70 mm tall at the back, sloping to 40 mm at the front. It bolts to two Cleat Bin Hanger Brackets set 80 mm apart with four M3x12 socket head cap screws, which pass through 3.4 mm rear-wall holes at x = ±40 mm and z = 15/45 mm and thread into the hangers' captured M3 nuts. Three 2.8 mm grooves at x = −26, 0 and +26 mm take the kit's slide-in dividers, and the front has a 100 x 14 mm label recess.
Small Scoop Cleat Wall Bin
An open-top scoop parts bin for the 'Printed French Cleat Bin Wall' kit. It measures 80 wide x 100 deep x 70 mm tall at the back, sloping to 40 mm at the front. It bolts to one Cleat Bin Hanger Bracket with two M3x12 socket head cap screws, which pass through 3.4 mm holes spaced 30 mm apart and thread into the hanger's captured M3 hex nuts. Inside are two divider grooves 2.8 mm wide at ±12.5 mm for the kit's slide-in dividers, and the front has a 50 x 14 mm label recess.
Wall Anchor Sort Tray With Drill Gauges
A 152 x 115 x 28 mm tray with five lanes (22–36 mm wide) for 5, 6, 8 and 10 mm wall plugs and hollow-wall toggles or mollies. Each lane has a scoop ramp at the front. The front ledge has a through-hole in front of each lane, sized for a 5, 6, 8, 10 or 12 mm bit (modelled 0.3 mm over nominal), so you can check the bit against the lane before drilling and there's no guessing which bit goes with which anchor.
E12 Resistor Twelve-Slot Index Box
A 105 x 55 mm box with 12 slots, one for each E12 value (10, 12, 15, 18, 22, 27, 33, 39, 47, 56, 68, 82). Each slot is 7 mm wide and 51 mm deep and holds small poly bags or taped strips of that value, one bag per decade. The front of each slot has 1 to 12 moulded dots, so you can find a value by counting, with no printed labels to smudge or peel. The top slopes from 45 mm at the back to 28 mm at the front, which leaves the bag tops easy to read and grab.
M3 To M8 Washer Tube Rack
Wall or bench rack with five coin-tube wells sized to real DIN 125 form-A flat washers — bores 7.8, 9.8, 10.8, 12.8 and 16.8 mm for M3 (7 mm OD), M4 (9), M5 (10), M6 (12) and M8 (16) — each with a front slot to see and thumb-push the stack and 52 mm of usable stack depth (about 32 M8 or 100 M3 washers). 74 x 69 x 26 mm overall; a 3 mm front shelf catches washers you pull out, 1 to 5 tally notches in the front lip name each bore, and two 4.5 mm M4 clearance holes 52 mm apart in the top rail sit clear of the tubes for a driver.
Hose Clamp Size Sorting Tower
A stepped cone that sorts a jumbled bag of worm-drive hose clamps by size — drop each clamp over the top and it hangs on the first shelf too wide for it. Eight tiers at 64, 56, 48, 40, 34, 28, 22 and 16 mm diameter over an 84 mm tall tower, on an 82 mm flange with three 4.5 mm M4 clearance holes to bolt it to a bench or pegboard shelf. Hollow conical core keeps it to about 45 cm³ of plastic.
Gridfinity 2x3 Screw-Down Baseplate
A six-socket Gridfinity baseplate on the standard 42 mm grid (41.6 mm sockets, 0.7/1.8/2.15 mm stacked-chamfer profile, 4.65 mm tall) so bins stop sliding around in a drawer. The 84 x 126 mm field carries four outboard tabs with 3.4 mm holes for M3 machine screws or #6 wood screws, 104 mm across overall; the open-bottom waffle frame keeps it to about 10 cm³ of plastic.
Hex Standoff Length Gauge Rack
A 124 x 28 x 28 mm staircase rack that sorts AND measures female-female hex standoffs: eight columns with pockets at 5, 6, 8, 10, 12, 15, 20 and 25 mm, all pocket floors on one plane so a standoff sitting flush with the rim is that length, proud is longer, sunk is shorter. Front lane bores are 7.0 mm (M2.5/M3 hex at 5.0-5.5 mm across flats, plus round spacers), rear lane 8.6 mm (M4 hex at 7 mm across flats), with 5 mm scale grooves down both sides and two 3.4 mm M3 clearance holes to screw it to a shelf or bench.
Comb-Slot Movable Divider Bin
A 140 x 92 x 28 mm drop-in parts-bin insert for a tool drawer, tote or case, with a 5.2 mm comb rail down both long walls so the two 86.5 x 23 mm dividers re-key into any of 24 positions — one print covers any mix of screw, nut and connector sizes instead of a fixed compartment layout. Dividers print flat in parking windows in the 2.4 mm floor, and two counterbored pads take M4 screws (4.5 mm clearance bore) to fix the insert down so it stops sliding.
Tilt-Out Wall Parts Bin
A print-in-place tilt-out parts bin: an 87 x 47 x 60 mm wall frame with a 70 x 41 x 50 mm bin hanging on captured 5 mm axles, so the bin self-closes by gravity and tips forward to pour screws or SMD parts into your hand. Mounts with two M4 screws through 4.5 mm holes on 56 mm centres, placed above the bin so a driver still reaches them; prints as one piece with no supports and 0.5 mm clearance on every mating face.