Heads up: many models on this page are AI-generated or uploaded untested. They may be misconfigured for the intended application — check the dimensions and tolerances, and verify or edit the model before printing or relying on it.*
RV Cabinet Self-Latching Spring Bolt
A surface-mount latch that prints in place. The bolt is pushed out by a built-in serpentine flexure spring. Its 45° ramped nose rides over a strike and snaps behind it, and a flared thumb tab pulls it back 6.5 mm to open. It replaces cracked RV and camper cabinet snap latches. The 44 x 32 x 18 mm body fixes to the door with two #8 wood screws through 4.5 mm holes, and the bolt sticks out 6 mm past the housing to catch behind a face frame or a screwed-on block.
Trailer Louvered Wall Vent Cover
A replacement exterior louvered vent for fiberglass travel trailers and campers whose OEM louvered vents are no longer made. It has a 130 x 100 mm flange around a 100 x 70 mm opening, with 45° rain-shedding slats on a 12 mm hood. Four 4.6 x 10.6 mm slots take #8 screws, so it can pick up most existing hole patterns.
Notched RV Roof Vent Prop Stay
A replacement prop arm for manual caravan/RV roof vents and hatch lids. It's a 168 mm long, 18 mm wide, 7 mm thick bar with a bossed 5.5 mm M5 pivot hole at one end. At the other end is a 90 mm slot with six notches 16 mm apart, so the stud on the lid can rest at six different opening heights. The slot lets it fit lids whose stud sits anywhere along that range, so you don't need the discontinued dealer part.
Pinch-Clamp RV Dump Valve T-Handle
A replacement T-handle for RV black and grey tank dump valves with an 8 mm stem. It clamps onto the stem with one M4 pinch bolt and a captured M4 nut, so you don't need a pin or set screw. The 110 x 58 x 16 mm grip lies flat on the printer bed so the pulling force runs along the layers, and it has finger scallops and lanyard slots. The 8.3 mm bore is 17 mm deep, with a 4 mm solid entry collar ahead of the split jaw.
RV Bay Door Snap Hold-Open Catch
A two-piece snap catch that holds an RV or trailer storage bay door open in the wind. A 9.6 mm knob on the door stud snaps through an 8.2 mm flexing fork mouth on the wall catch. Both parts are 60 x 20 mm mounting bars with two 4.6 mm holes on 44 mm centres, for #8 wood screws or M4 bolts and nuts. It prints already snapped together.
RV Shower Door Gravity Hook Latch
A print-in-place gravity hook that replaces the webbing strap that usually wears out on RV shower stall doors. The 21 x 28 mm base screws to the jamb with two #6 wood screws (4.0 mm holes, 7.5 mm counterbores). A 6 mm pivot pin carries a 61 mm swing arm with 0.5 mm clearance, and the arm drops over a #8 pan-head screw in the door through its 5 mm notch with a ramped lead-in, so the door stays shut while you drive.
Occupied/Vacant Door Slide Indicator
This print-in-place indicator shows whether a bathroom is occupied, like the ones on aircraft doors. It is sized for RV, campervan, tiny-home and shared-rental bathroom doors. Slide the thumb knob and a red flag moves into the 24 x 11 mm window in the green housing. The housing is 100 x 40 x 5.5 mm and fastens to the door face with two countersunk #6 or #8 wood screws (4.5 mm holes, 86 mm apart). The slider moves 33 mm between the two states and is held in place by the door face once the housing is screwed down.
Cellular Grid RV Stabilizer Jack Pad
This 130 x 130 mm pad goes under the small OEM foot of a scissor or screw stabilizer jack on an RV or trailer, so the foot doesn't sink into gravel or soft ground. Any foot up to 120 mm across sits inside the lipped tray. The open 21.7 mm grid cells underneath (8 mm deep) fill with soil and lock the pad in place. Drain notches let rain run out, and a pull tab with a 20 mm finger hole lets you slide it back out from under the jack.
RV Fridge Three-Step Airing Prop
A red stepped wedge that holds an RV or camper fridge door 15, 25 or 35 mm ajar during storage, so the fridge doesn't grow mold. It replaces the airing card that keeps snapping, and it works without knowing the door latch geometry. The body is 75 x 35 x 18 mm with ribbed pockets, and the tab has a 6 mm hole so you can tie it to the door handle and it doesn't get lost.
Fire Extinguisher V-Cradle Strap Bracket
A wall bracket with a V-shaped cradle that centres any fire extinguisher body from about 70 to 130 mm across, which covers typical 2.5 to 10 lb units. It replaces a cracked OEM strap bracket in a garage, RV, boat or kitchen. The plate is 140 x 42 mm, the arms reach out 50 mm, and it mounts with two #10 or M5 screws through 5.5 mm holes. A 25 mm hook-and-loop strap or 1 in webbing runs through the 27 mm slots at the arm tips. Measure your extinguisher body before you order. For vehicles, fit one near the top and one near the bottom of the body.
Blade Fuse Assortment Tray With Puller Trench
A stepped 130 x 80 mm bench or glovebox tray that holds blade fuses upright by amperage. It has 14 mini slots (4.8 x 12.5 mm), 12 ATO/ATC slots (6.2 x 20.8 mm) and 3 maxi slots (9.8 x 30.6 mm), plus an 11 x 72 mm trench that takes the fuse puller. The slots are cut a little oversize compared with the usual fuse bodies (10.9 x 3.6 mm mini, 19.1 x 5.1 mm ATO, 29.2 x 8.5 mm maxi), so the fuses drop in and stand with their heads up for grabbing. Two 4.5 mm holes let you screw it down with #6 or M4 screws inside a van, RV or electronics cabinet.
Flagged: automotive electrical. Not for safety-critical use without independent engineering review.
RV Awning Pole Ground Foot
A 76 mm wide ground foot that stops an RV awning or canopy pole from sinking into dirt, gravel or grass. The 57 mm socket takes a 1 in (25.4 mm) pole end down to a 7/8 in (22.2 mm) step, each with a 5.5 mm cross hole for an M5 bolt or clevis pin, and three 5.5 mm stake bosses at a 60 mm circle let you peg or screw it down.
Twin-Arm RV Cabinet Snap Catch
A twin-arm spring catch that replaces the brittle plastic friction latches in RV, caravan and boat cabinets: two 2.6 mm cantilever jaws with cam lobes grip a 3 mm strike tongue (holds 2.5–3.5 mm), with moulded overtravel stops so the arms can't be splayed past 1.2 mm. The 66 x 30 x 3.5 mm flange mounts with four 4.5 mm M4 clearance holes on 36 mm and 56 mm spacings, and the whole catch stands 11 mm proud.