Heads up: many models on this page are AI-generated or uploaded untested. They may be misconfigured for the intended application — check the dimensions and tolerances, and verify or edit the model before printing or relying on it.*
Gridfinity 1x1 Four-Cell Half-Grid Bin
A standard Gridfinity 1x1 bin (41.5 x 41.5 mm, 3 units / 21 mm tall, no stacking lip) split into four 18 x 18 mm cells on a 21 mm half-grid pitch. Each cell has a 45° scoop ramp at the front. It gives desk and bench Gridfinity grids the finer sorting that SMD parts, small screws and connectors need, without moving to a non-standard baseplate.
Label-Window Drawer Pull
A finger pull and slide-in label holder, part of the '2020 Gridfinity Drawer Tower' kit. It has a 124 x 36 x 4 mm backplate and a 16 mm deep tapered lip. Two M3x14 screws go through its 3.4 mm holes at ±55 mm and the Drawer Front Panel and into the tray's self-tap pilots, so your pull lands on the tray. An 84 x 14 mm window shows an 86 x 18 mm card up to 0.8 mm thick, which slides into a 1 mm back slot that is open at the top.
Drawer Front Panel
Part of the '2020 Gridfinity Drawer Tower' kit. This 192.5 x 50 x 6 mm drawer face covers the 131.5 mm Gridfinity tray and both front 2020 posts. When you push the drawer in, the panel stops against the post fronts, so the impact goes into the frame and not the screws. Mount it with two M3x14 screws that pass through the pull, then through 3.4 mm holes at ±55 mm, then into the tray's self-tap pilots. A 1.5 mm locating rim on the back holds the panel square on the tray, and gaps in the rim clear the runner ends.
Gridfinity 3x3 Drawer Tray
This open-top drawer is part of the '2020 Gridfinity Drawer Tower' kit. Outside it measures 131.5 x 135 x 45 mm, and the 126.5 x 126.5 x 42.6 mm interior takes a 3x3 Gridfinity baseplate or 41.5 mm bins. The tray slides on the kit's twin-detent runners with 0.5 mm of clearance per side. Four 7 x 1.2 mm floor notches click over the runner ridges, and two 2.6 mm M3 self-tap pilots in the 6 mm front wall hold the front panel and pull with M3x14 screws.
Twin-Detent Drawer Runner
Part of the '2020 Gridfinity Drawer Tower' kit. This 135 x 20 x 16 mm side rail bolts to the inner slots of a front and a back 2020 post with two M5x10 socket-head screws and drop-in T-nuts. The 5.5 mm holes sit 115 mm apart and have 10 x 5.5 mm counterbores, so the heads end up below the face. A 6 x 5 mm ledge carries one side of a Gridfinity tray. Two 0.8 mm half-round ridges click into the tray's notches. The ledge ends have 1.5 mm lead-in chamfers. The part is symmetric, so all 8 runners are identical.
Tower Frame End Plate
Part of the '2020 Gridfinity Drawer Tower' kit: a 198.5 x 141 x 6 mm frame plate that holds four 2020 aluminium extrusion posts. It uses the same part at the base and, flipped, as the top cap. Each post sits in a 20.4 mm U-socket, 20 mm deep and open on the front or back so the drawer fronts can pass. Each socket takes three M5x8 screws into drop-in T-nuts through 5.5 mm holes. Four 4.6 mm holes take #8 wood screws, and the 39.25 mm side bars act as the top drawer's hold-down.
Gridfinity 1x2 Twin Scoop Bin
A true-spec Gridfinity 1x2 bin — 41.5 x 83.5 mm footprint on the 42 mm grid, 28 mm tall (4 height units) — with the full three-step foot profile (35.6 / 37.2 / 41.5 mm) so it drops into any standard baseplate, and a matching stacking lip on top. Inside it is split into two 18.3 mm lanes, each with a 45 degree scoop ramp at the front so M3 screws, nuts and standoffs sweep straight out into your fingers.
Gridfinity 2x3 Screw-Down Baseplate
A six-socket Gridfinity baseplate on the standard 42 mm grid (41.6 mm sockets, 0.7/1.8/2.15 mm stacked-chamfer profile, 4.65 mm tall) so bins stop sliding around in a drawer. The 84 x 126 mm field carries four outboard tabs with 3.4 mm holes for M3 machine screws or #6 wood screws, 104 mm across overall; the open-bottom waffle frame keeps it to about 10 cm³ of plastic.