Heads up: many models on this page are AI-generated or uploaded untested. They may be misconfigured for the intended application — check the dimensions and tolerances, and verify or edit the model before printing or relying on it.*
13-Bit Hex Shank Spade Bit Stand
A stand that holds a 13-piece set of 1/4 in hex-shank spade bits upright with the points up. It has 6.8 mm across-flats hex sockets, 18 mm deep, laid out in two staggered rows on a 26 mm pitch, and the back row is 12 mm higher so the paddles don't hit each other. It holds paddles up to 25 mm wide (1 in), is 172 x 44 x 36 mm, and screws to a bench or shelf through two 4.5 mm holes that take #8 wood screws or M4 bolts.
Chainsaw File Four-Size Bench Caddy
Bench or wall caddy with stepped ribs that hold chainsaw round files upright, sorted by size: three wells each for 5/32 in (4.0 mm), 3/16 in (4.8 mm), 13/64 in (5.2 mm) and 7/32 in (5.5 mm) files. The wells are bored 0.6 mm oversize at 4.6/5.4/5.8/6.1 mm. A wide 8 x 30 mm slot takes a flat file or depth-gauge tool, and two 4.5 mm holes take #8 screws. The base is 112 x 72 mm, the ribs step up from 24 to 36 mm tall, and tick notches mark each size so worn and new files stop getting mixed up in the saw box.
TIG Tungsten Four-Size Stepped Rack
This stepped bench rack holds 24 TIG tungsten electrodes upright, sharp end up, with 6 per size: 1.6 mm (1/16 in), 2.4 mm (3/32 in), 3.2 mm (1/8 in) and 4.0 mm (5/32 in). The holes are 2.2, 3.0, 3.8 and 4.6 mm, and dimples on each step mark the size. Ground tips stop knocking together in a drawer, and the size you need is easy to grab. The rack is 80 x 56 mm with steps from 30 to 48 mm high. It is hollow with ribs inside, and each electrode stands in a floor socket under its hole.
Twelve-Slot T-Shank Jigsaw Blade Block
A two-tier bench block that holds 12 T-shank jigsaw blades upright with their teeth showing, so you can grab the right blade without digging through a pile of cardboard sleeves. It is 110 x 44 x 32 mm and has two staggered rows of six 2.4 x 11 mm slots, 12 mm deep. The slots fit common blades from about 1.3 mm thick and up to about 10 mm wide at the shank, and the rear tier is hollowed out underneath to save plastic.
Flagged: a sharp edge or blade. Not for safety-critical use without independent engineering review.
DIP And SOIC IC Tube Lane Rack
A 158 x 45 x 60 mm upright rack for anti-static IC shipping tubes (partial or full). It has ten boxed lanes, each 14 mm deep: two 20 mm lanes for wide DIP-600, four 14 mm lanes for DIP-300 and four 10 mm lanes for SOIC. Each lane has a 12 mm front lip and a top retaining bar, with an open window between them so the part number printed on the tube stays readable. Screw it to the wall through two 4.5 mm holes in the back, or to a shelf through the 45 mm foot plate. The lanes are made loose so tubes from different makers fit. Measure your tubes before ordering.
Test Lead And Clip Wall Rack
A 150 mm wide wall rack with ten 5.2 mm drop-in slots. Each slot takes a meter lead or patch lead with wire up to about 5 mm OD, and the banana plug or probe body rests on top so the leads hang straight and don't tangle. A 3 mm clip rail along the top holds alligator and hook clips. Two gussets and the center rib brace the 40 mm deep shelf. Mount it with two #8 wood screws or M4 bolts through the 4.6 mm holes, which are 90 mm apart.