Heads up: many models on this page are AI-generated or uploaded untested. They may be misconfigured for the intended application — check the dimensions and tolerances, and verify or edit the model before printing or relying on it.*
Wobbly Chair Dowel Hole Rebuild Sleeves
A snap-off sprue of six crush-ribbed sleeves for rebuilding wallowed-out dowel holes in chair and table joints. Drill the worn hole out to 12 mm and glue in an 8 mm sleeve (25 mm long, 8.3 mm bore), or drill to 14 mm and use a 10 mm sleeve (30 mm long, 10.3 mm bore). Six 0.3 mm crush ribs bite into the wood and leave channels for the glue, and the chamfered nose starts the sleeve straight in the hole.
Dual-Flush Button 48 To 38 mm Lid Bushing
Stepped reducer bushing that seats a 38 mm-thread dual-flush push button in a cistern lid bored for a 48 mm button: 38.6 mm bore, 47.6 mm sleeve with six crush ribs to 49 mm that centre it in the ceramic hole, 60 mm x 3 mm top flange the button bezel lands on. Four snap-off 2 mm spacer rings on the sprue (two 38.6 mm bore, two 49 mm bore) take up thread length so the retaining nut clamps tight instead of leaving the button wobbling or cracking the lid.
Glovebox Hinge Rebush Kit For 5 mm Pin
A sprue-frame kit for fixing sagging glovebox and console lids. You drill each worn, oval pivot hole out to a round 10 mm and press in a flanged bushing (9.8 mm body, crush ribs to 10.4 mm, 14 mm flange). A 5 mm steel rod then serves as the new hinge pin, in a 5.3 mm slip-fit bore, and two push-on collars hold the rod in place. The kit is four bushings and two collars on a 109 x 24 mm frame.
Folding Chair X-Pivot M5 Bushing Kit
Two sets of bushings for rebuilding a worn folding-chair X-pivot with an M5 bolt once the rivet is drilled out to 10 mm. Each set has a flanged head bushing, a flanged bushing with a captured M5 nut (8 mm AF pocket) and a 20 mm spacer washer, all with 5.5 mm bores and 9.8 mm sleeves. The pieces print joined by snap-off tabs.
Office Chair Caster Socket Repair Sleeve
This sleeve repairs a cracked caster socket on an office chair base. Drill the split socket out to 16 mm (5/8 in), then epoxy the sleeve in place. The 11.2 mm bore takes the common 11 x 22 mm grip-ring caster stem, and the 28 mm tube is longer than that stem. A 32 mm washer flange spreads the load across the underside of the leg. Three V-grooves hold the epoxy.
Mower Wheel Axle Bushing Set
A snap-apart run of three split flanged sleeve bushings for worn mower, wheelbarrow, snowblower and hand-truck wheels — bores of 13.1, 16.3 and 19.5 mm for 1/2", 5/8" and 3/4" axles (12.7 / 15.88 / 19.05 mm), each 25 mm long with a 2.5 mm thrust flange (25.0 / 28.2 / 31.4 mm flange dia). Bodies are 19.0 / 22.2 / 25.4 mm OD with six crush ribs taking them to 21.0 / 24.2 / 27.4 mm, so one bushing presses into any hub bore across that range; a 2.4 mm axial split lets it spring onto the axle and pinch down into an undersize bore, and two internal grease channels keep it fed. Snip the 1.2 mm webs with side cutters and use the size you need — the whole card is 95 x 31 x 27.5 mm.