Heads up: many models on this page are AI-generated or uploaded untested. They may be misconfigured for the intended application — check the dimensions and tolerances, and verify or edit the model before printing or relying on it.*
Gusseted Upright Napkin Holder
An upright napkin holder for the table or counter. Two 3 mm walls stand 80 mm tall with a 36 mm gap between them, on a 178 x 60 mm base. Folded paper napkins stand on edge between the walls and are free to hang past the open ends. Six radiused windows let you see how many napkins are left and grab the last few. Four 45° gussets brace the walls so they stay stiff and don't splay when you pull a napkin out.
Undermount Sink Jack-Screw Rim Clip
A replacement clip for an undermount kitchen sink, 70 x 20 x 18 mm. The nose presses the sink flange up against the counter. A 7 x 24 mm slot takes the countertop's existing 1/4 in or M6 stud or screw, and an M4 heat-set insert lets a jack screw in the heel set the height, so one clip fits any rim thickness. It prints on its side so the clamping load runs along the layers. Print 6–10 clips in PETG to re-hang a sagging sink.
Reusable Straw And Brush Drying Rack
This is a countertop rack for drying reusable straws. Ten straws stand upright on drain ribs, so their open ends never sit in water. A 13 mm-deep guide bar holds them straight. It has two 13.5 mm holes for 12 mm boba straws, four 9.5 mm holes for 8 mm straws and four 7 mm holes for 6 mm straws and cleaning brushes. The rack measures 130 x 45 x 90 mm and has a 5.6 mm-deep drip tray. Two 4.6 mm holes in the back wall take #8 screws if you want to mount it on the wall.
1/2 in PVC Mug Tree Six-Peg Hub
This hub turns a length of 1/2 in Schedule 40 PVC (21.3 mm OD, 21.7 mm slip bore) and six 8 mm dowels into a countertop or under-shelf mug tree. Each dowel sits in an 8.3 mm socket 18 mm deep, angled up at 45°. An M4 heat-set insert takes a thumb screw that locks the hub at any height on the mast. The hub is 66 mm across and 32 mm tall, and you can stack two hubs turned 30° apart to hang 12 mugs.
Six-Cell Utensil Crock Divider Insert
A drop-in insert that splits a round utensil crock into six cells plus a 13 mm centre tube. It stops spatulas, whisks and tongs from tangling into one jammed bundle. It is 96 mm across and 100 mm tall, so it fits any crock with an inside diameter of 100 mm or more. The top edges slope down toward the rim so utensils slide in easily, and bridged notches at the foot of each fin let rinse water drain between the cells.
Spring-Diamond Stove Gap Cover
A 170 mm stove-to-counter gap cover with a 44 mm wide cap strip and a stem made of two hollow 45° diamond springs, 14 mm and 10 mm wide. They squeeze into gaps of about 6–13 mm and stop crumbs and spills from falling down the side of a freestanding range. Cut it to length or butt several pieces together, and print it in PETG if the range side gets warm.
Nine-Offset Pencil Scribing Gauge
A 150 x 55 mm flat scribing plate for marking cabinets, countertops, shelves and trim to fit wavy walls and floors. Ride its straight edge along the wall and trace a line 5, 8, 10, 12, 15, 20, 25, 30 or 40 mm away. Each station is a 60° cone ending in a 2.4 mm hole, so the point of any sharpened pencil (standard or carpenter's) settles on the same exact line. A 16 mm tall rib along the back works as a grip and keeps the plate from flexing.
Twin Wine Bottle Counter Cradle
This rack holds two standard 750 ml wine bottles on their side on a counter, pantry shelf or fridge shelf. Each cradle is a 40 mm radius arc: bottles 70–80 mm across settle into it, and bottles up to about 90 mm (sparkling wine) sit on the arc edges. It measures 176 x 42 x 55 mm and is a hollow frame with 2.4 mm walls, like an aluminium extrusion, so it stays light. It prints standing on its end with no supports, so the bottle's weight presses along the layers rather than trying to peel them apart.
Appliance Cord Wrap Cleat With Cord Lock
This cleat sticks to the back of a stand mixer, air fryer, blender or toaster with VHB tape, or screws on with two M4 or #8 screws through 4.5 mm holes. The cord wraps around two 20 mm-wide hooks, 72 mm apart outside to outside. The hooks have 45° undercut lips that stop the loops sliding off. A tapered centre slot, 3.5 to 8 mm wide, grips a 4–8 mm cord or the plug tail so the cord doesn't hang loose over the counter. The plate is 90 x 36 x 3 mm and the whole part is 28 mm tall.
Three-Slot Cutting Board Drying Stand
A countertop stand that holds three cutting boards on edge so both faces air-dry and don't trap water. It has two open comb rails, 122 mm long and set 84 mm apart, joined by low cross bars. Each slot is 22 mm wide at the floor and flares to 34 mm at the top, so boards up to 20 mm thick drop in easily and lean back into the V.