Heads up: many models on this page are AI-generated or uploaded untested. They may be misconfigured for the intended application — check the dimensions and tolerances, and verify or edit the model before printing or relying on it.*
Mower Height Lever Set-Screw Grip
Replacement grip for a push-mower or zero-turn height-adjust lever whose plastic knob has cracked off. It is 90 x 36 x 18 mm and has a 24 x 7.5 mm slot, 50 mm deep, that takes any flat bar up to 24 x 7 mm or round rod up to 7 mm. Two M4 set screws in brass heat-set inserts (5.5 mm bores) clamp it to the bar, so you don't need the exact OEM size.
Undermount Sink Jack-Screw Rim Clip
A replacement clip for an undermount kitchen sink, 70 x 20 x 18 mm. The nose presses the sink flange up against the counter. A 7 x 24 mm slot takes the countertop's existing 1/4 in or M6 stud or screw, and an M4 heat-set insert lets a jack screw in the heel set the height, so one clip fits any rim thickness. It prints on its side so the clamping load runs along the layers. Print 6–10 clips in PETG to re-hang a sagging sink.
Pantry Shelf Can Fence Label Clamp
A 50 mm wide clamp that fits over the front edge of a pantry or cabinet shelf. It adds a 30 mm fence so cans and jars can't roll off, and has a slide-in label channel (1 mm slot, 22 mm visible window) on the front. The jaw opens to 20 mm and an M4 thumb screw in a heat-set insert from below tightens it, so it fits any shelf from 12 to 19 mm thick (5/8 and 3/4 in melamine or plywood) with no drilling.
Screw-Clamp Breaker Handle Lockout
A clamp-on lockout for single-pole breakers. It fits over the toggle through a 10 mm channel, and an M4 screw in a brass heat-set insert clamps toggles 1–10 mm thick: use M4x25 for 1–7 mm and M4x20 for 6–10 mm. A padlock shackle up to 7 mm goes through the vertical hole and blocks the screw head, so nobody can loosen the clamp until the lock comes off. The body is 51 x 20 x 20 mm and fits within the 25.4 mm breaker pitch.
Oven Door Handle Clamp-On Towel Hook
A towel hook that screw-clamps onto any round oven or dishwasher door bar from 16 to 30 mm across, so it can't slide off. A 90° V-crown sits on top of the bar and an M4 bolt in a heat-set insert (5.5 mm bore) pushes up from below to lock it. It is 16 mm wide and about 75 x 101 mm overall, and needs about 24 mm between the bar's centre and the door.
V-Grip Drill Bit Depth Stop Collar
This slip-on depth stop collar fits any straight-shank drill bit from 3 to 8 mm. An M4 thumbscrew in a brass heat-set insert (5.5 mm bore) clamps the bit into a 90° V-channel, so one collar replaces a whole set of fixed-size stops. The 32 mm flange rests flat on the workpiece, which makes it good for repeatable shelf-pin, dowel and cam-lock re-drilling in flat-pack furniture repairs.
Office Chair Height Lever Paddle
A replacement seat-height lever paddle for an office chair whose plastic paddle snapped off the metal actuator tab — 119 mm long overall with a 95 mm reach, 28 mm wide, ribbed top and an upturned finger lip at the tip. The clamp head takes a 16 x 8 mm through-slot (fits a flat lever tab up to 15 x 7 mm, or round stock up to 7 mm) and locks onto it with two M4 screws in 5.5 mm heat-set insert bores, pressing the tab down onto two ridged floor rails.
Over-Door Towel And Robe Hook
A clamping over-the-door double hook for wet towels and robes on a bathroom door: the 38 mm throat and 2.4 mm flexure tongue are squeezed by an M4 screw in a 5.5 mm heat-set bore, so it locks to any 32–38 mm door (a standard 1-3/8 in / 34.9 mm interior door sits mid-range) instead of swinging and scuffing paint. The bridge over the door top is only 3.2 mm thick so the door still shuts, the strap is 22 mm wide, and the part is 82 x 95 mm overall with a robe hook 36 mm down and a deeper towel hook at 82 mm.
Shelf Board Monitor Riser Leg
A printed end leg that turns a scrap of 12–20 mm shelf board into a monitor riser: the board drops into a 20.5 mm slot at the top and two M4 brass heat-set inserts take clamp screws that pinch it solid. 92 mm tall, 80 mm deep foot with four M4 clearance holes for desk-mat feet or a bench screw, ribbed and windowed web so it prints fast without supports.
Print-In-Place Ratchet Lift Post
A print-in-place ratcheting height post: a 16 mm toothed column on a 50 x 50 mm bolt-down foot with a captured pawl collar that clicks up in 10 mm steps over 70 mm of travel and locks under downward load. Overall 110 mm tall; the foot takes four M4 screws and the support pad takes two M4 heat-set inserts (5.5 mm bores) so you can bolt a shelf, sensor or workpiece rest to it — pull the thumb tab to release and lower.
Universal Pot Lid Knob Replacement
A drop-in replacement knob for a glass or metal pot lid whose original knob has cracked, melted or gone missing: Ø46 mm heat-shield flange, 33 mm tall six-flute grip, and a Ø5.5 x 12 mm bore for an M4 brass heat-set insert so the lid's own screw threads into metal. Cored out to about 18 cm³, prints flange-down with no supports — print it in PETG or ASA, not PLA, since lid knobs sit above a hot pan.
Pannier Rack Rail Hook Block
A universal pannier mounting hook for bike rack rails: a 90-degree V-groove seat self-centres on any round rail from 8 to 16 mm, and an M4 bolt through the outer leg into a heat-set insert closes the 17 mm mouth so the bag cannot bounce off. The block is 34 x 48 x 24 mm and bolts to the bag panel with two M4 heat-set inserts on 26 mm centres, replacing brand-specific hooks that cost about $15 each and do not fit generic or e-bike racks.
Sous Vide Circulator Rim Clamp
Replacement pot clamp for a sous vide circulator whose OEM plastic clamp has snapped — a 38 x 80 x 46 mm C-clamp that hooks over any pot wall or Cambro/Rubbermaid tub rim up to 18 mm thick and locks down with an M4 thumbscrew running in a 5.5 mm heat-set insert bore. A 90° V-channel cradles any circulator barrel from 40 to 70 mm diameter and two 9 x 4 mm slots take a zip tie or velcro strap to bind the barrel into the V. The C-profile lies in the bed plane so the clamping load runs along the layer lines, not across them.
Aquarium Rim Clamp Hose Saddle
A screw-adjustable clamp that hooks over an aquarium rim or bare glass up to 18 mm thick and carries a 90° saddle trough for a filter hose, heater cord, CO2 line or probe cable, with a 3.5 x 8 mm zip-tie slot under the trough to lock the line down. Overall 64 x 37 x 25 mm; tightens with an M4 x 30 screw into an M4 heat-set insert (5.5 mm bore) in the outer jaw, so it fits rimless tanks, trimmed tanks and sump baffles without a single guessed dimension.
Register Vent Air Deflector Clamp
A 150 mm wide, 50°-angled deflector blade that screw-clamps onto the outermost louver fin of a floor, wall or ceiling HVAC register to throw supply air away from curtains, a bed or a sofa instead of straight up the wall. Two clamp posts take an M4 heat-set insert (5.5 mm bore) and an M4 set screw that pins any fin up to 12 mm thick against an 8 mm anvil, so it works on stamped steel and moulded plastic registers alike — unlike magnetic deflectors that slide off. Blade is 2.6 mm thick with three full-length stiffening fences; overall 150 x 69 x 66 mm, prints rail-down with no supports.
Split Keyboard Tenting Riser
A 19° tenting wedge for one half of a split ergonomic keyboard (Corne, Lily58, Sofle, Iris and friends) — 88 x 74 mm footprint, 11 mm at the inner edge rising to 42 mm at the outer, with a 4.6 mm lip so the board can't slide down the slope and an open notch for the TRRS/USB cable. Two M4 brass heat-set inserts (5.5 mm bores, in the bottom face) take M4 bolts as screw-adjustable outer feet, so you can trim the tent angle by a few degrees; the body is an open egg-crate frame of 4 mm vertical ribs, so it prints without a single support and carries the load along the layer plane. Print two — flip the model for the other hand.
52 mm Gauge Pod Panel Mount
A single-hole pod for a standard 52 mm (2-1/16") boost, oil-pressure or volt gauge: Ø52.4 mm bore, 36 mm deep, stepping down to a Ø48 mm shoulder that stops the gauge and lets the harness exit straight through the base. The cup sits at 18° on a flat 92 x 78 x 5 mm plate with four M4 clearance holes (VHB-friendly underside), and two M4 heat-set inserts in the flank pads take nylon-tip set screws that lock the barrel — total height about 58 mm, prints on the plate with no supports.
Flagged: automotive electrical. Not for safety-critical use without independent engineering review.
Desk Edge Clamp-On Scrap Bin
A 74 x 55 x 44 mm open bin that hangs off the front edge of a desk or bench so clipped component leads, wire offcuts and eraser crumbs get swept straight off the surface instead of onto the floor. Twin sleeve jaws slide over desktops 18–25 mm thick and lock with two M4 x 25 screws in 5.5 mm heat-set inserts; the rim sits 8 mm below the work surface and the spine finishes flush with it.
Seat Belt Buckle Webbing Stop Clamp
A one-piece C-clamp that grips a car seat-belt web (47 mm wide, ~1.2 mm thick) so the latch tongue stops sliding down out of reach — the belt slides in sideways through the 2.4 mm slot and two M4x20 screws into M4 heat-set inserts pinch it closed on two grip ribs. 71 x 20 x 26 mm, clamping 26 mm of webbing across its full width.
Hacksaw Blade Jab Saw Handle
A one-piece handle that turns a snapped 12.5 mm hacksaw blade into a jab saw for cutting in tight spots — 148 mm long with a 1.6 mm x 13.5 mm blade slot 55 mm deep, so the blade bottoms out on a solid end stop for push cuts. Two M4 brass heat-set inserts (5.5 mm bores) take M4 set screws that pinch the blade against the far slot wall; the grip is 22 x 26 mm with finger scallops, a hollow ribbed core, and an 8 mm hanging hole for a pegboard hook.
Flagged: a sharp edge or blade. Not for safety-critical use without independent engineering review.
Monitor Side Document Copy Holder
A screw-clamp copy holder that grips the side edge of a monitor panel (8–24 mm thick edge, 20 mm throat) and carries a 1.4 mm paper slot 51 mm out to the side so notes, invoices or a wiring diagram stand upright next to the screen. 89 x 42 x 22 mm, clamped by an M4 thumbscrew running in a 5.5 mm heat-set insert bore, with a through groove on the bezel jaw for a stick-on foam pad.
Frameless Shower Door Saddle Hook
A clamp-on double hook that saddles the top edge of a frameless glass shower door — towel hook on the outside, loofah/razor hook on the inside, no drilling, adhesive or suction cup. The 13.6 mm slot with a raised grip pad takes 6–13 mm (1/4"–1/2") tempered glass, and an M4 heat-set insert (5.5 mm bore) plus an M4x16 screw locks it down; 76 x 43 x 26 mm.
Desk Edge Cable Drop Comb
A clamp-on comb that grips the back edge of a desk or shelf (tops up to 27 mm thick) and drops five cables down in separate channels instead of one tangled bundle — two 10 mm channels for laptop/power bricks and three 7 mm channels for USB and audio leads, each with a snap-in mouth so cables push in from the side and stay put. 57 mm wide, 42 mm tall, no drilling: an M4 brass heat-set insert (5.5 mm bore) in the lower jaw takes an M4 x 20–25 bolt that jacks up against the underside of the desktop.