Heads up: many models on this page are AI-generated or uploaded untested. They may be misconfigured for the intended application — check the dimensions and tolerances, and verify or edit the model before printing or relying on it.*
Dishwasher Drain Hose High-Loop Saddle
This saddle screws to the inside wall of a sink cabinet. It holds the dishwasher drain hose in a code-style high loop around a 40 mm radius so the hose can't kink, sag or siphon. A 26 mm wide grooved channel takes corrugated drain hose from about 16 to 25 mm OD, and two zip-ties per station pass through slots in the core. The 140 x 60 x 49 mm flange takes three #8 wood screws through 5 mm clearance holes.
Under-Sink Trash Bag Roll Rod Bracket
A pair of these screw to the inside wall of an under-sink cabinet with #8 wood screws (5.2 mm holes), and an 8 mm smooth rod runs through the 8.4 mm bores and the core of a trash-bag roll, so you can tear bags off one-handed. Each bracket is 72 x 104 x 14 mm, with a gusseted arm that holds the rod 62 mm out from the wall. It's printed flat so the load runs along the layers, not across them.
Dishwasher Pod Gravity Dispenser
This is a gravity-feed dispenser for dishwasher detergent pods that screws to the inside of a sink-cabinet door. You load pods from the open top and pull them out one at a time from the bottom slot. A 3 mm lip stops the bottom pod from sliding out when the door swings. The chute is 50 mm wide and has 40 mm of depth under the 45° front lips, so pods up to about 48 x 38 mm of any thickness fit. It holds 6–7 pods in a 55 x 160 x 54 mm body. It prints flat on its back with no supports and mounts with two #8 (4.2 mm) pan-head screws through 4.5 mm holes. Pods are a poisoning risk, so mount it high inside a child-latched cabinet.
Under-Sink Filter Housing Strap Wrench
This strap-wrench handle takes a loop of standard 25 mm (1 in) nylon webbing, so it fits seized under-sink and RO filter housings of any diameter, stuck jar lids and canister tops. You don't need the brand-specific plastic spanner that came in the box. The handle is 172 mm long and the head is 48 x 32 mm. The webbing is anchored with an M5 x 35–40 bolt in a captive nut pocket and runs back through a 26.5 x 4 mm return slot. A 28 mm-wide V nose keeps the head centred on the housing.
Garbage Disposal Mount Ring Lug Wrench
A 172 mm lever wrench for turning the twist-lock mounting ring on a kitchen sink disposal. A tapered fork slips over any ring lug or tab from 3 to 10 mm thick, so the tool doesn't depend on any one brand's lug size. A hex pocket in the handle stores the 1/4 in jam-clearing key, and an 8 mm hole lets you hang the wrench under the sink.
P-Trap Slip Nut Toothed Spanner
A flat spanner, 171 x 94 x 10 mm, for turning the plastic slip nuts on P-traps and tailpieces under a sink. Its 60° V-jaw has V-shaped teeth that grip any round or ribbed nut from 40 to 75 mm across, so it covers the common 1-1/4 in and 1-1/2 in drain nuts without rounding them off like channel-locks do. The 8 mm thick handle slides into tight cabinets and has a 7 mm hang hole.
Under-Sink Spray Bottle Hanger Rail
A 180 mm screw-on rail for the inside wall of an under-sink cabinet. It hangs three trigger spray bottles by the neck, so they stop tipping over in the cabinet base. Each 60 mm-deep shelf has a tapered slot that narrows from 34 mm to 22 mm, so necks of different sizes wedge in and the trigger head sits on top. Slots are on 62 mm centres. Four 4.5 mm holes take #8 (4.2 mm) wood screws, and four 45° gussets carry the load.
Under-Sink Inline Water Filter Bracket
A wall/cabinet bracket that holds a standard 2 in inline water filter (fridge ice-maker, RO post-filter, whole-line carbon) off the plumbing instead of letting it hang on the tubing and kink the push-fits. Twin 90° V-block saddles self-centre any 45–56 mm filter body and a 4.8 mm zip tie through each saddle straps it down; snap-in end clips route 1/4 in (6.35 mm) OD tubing, and four 4.5 mm holes take #8 wood or M4 screws. 130 × 48 × 34 mm, prints flat with no supports.
Under-Sink P-Trap Riser Shelf
A 140 x 95 mm riser shelf that slides in around a bathroom sink drain so the dead space beside the P-trap becomes usable storage — the 52 mm wide U-slot (26 mm end radius) clears common 1-1/4 in and 1-1/2 in tubular tailpieces and their slip nuts. Four hollow 18 mm legs give 45 mm of clearance over the cabinet floor, 7 mm drain slots let a drip pass straight through instead of pooling under your bottles, and each foot has a 4.5 mm M4 clearance hole if you want to screw it down.