Heads up: many models on this page are AI-generated or uploaded untested. They may be misconfigured for the intended application — check the dimensions and tolerances, and verify or edit the model before printing or relying on it.*
Hose-Clamp Camp Chair Cup Holder
This cup ring clamps onto camp chairs, canopy legs, boat rails or wagon frames made from round tube between 16 and 32 mm. A 90° V-jaw centres the tube and a band tunnel takes a standard 8 mm or 12.7 mm worm-drive hose clamp or a zip tie. The 82 mm bore fits 66 mm cans and most tumblers, which sit on an 11 mm lip with an open 60 mm centre so rain drains straight through. Overall size is 136 x 88 x 40 mm.
Monitor Arm Pole Strap-On Phone Tray
A 100 x 70 mm tray with 20 mm walls that straps onto the vertical pole of a monitor arm. It gives you a spot for a phone, earbuds or a remote without using any desk space. A 90° V-saddle grips poles from about 20 to 38 mm diameter. Two pairs of 4.5 x 22 mm slots take a worm-drive hose clamp (up to 13 mm band) or a 20 mm hook-and-loop strap, and a notch in the front wall lets a charging cable through.
Generator Frame Tube Hose-Clamp Foot
This replaces the cracked plastic foot on a portable generator's wheel kit or tube frame. A 90° V-saddle sits on any round frame tube from 19 to 32 mm OD and lifts it 40 mm off the ground. Two 1/2 in (12.7 mm) worm-drive hose clamps strap it on through 13 x 3 mm tunnels. The 70 x 56 mm hollow ring base takes the generator's weight in compression.
Canopy Leg V-Block Guy-Line Anchor
A 90° V-block that straps to a pop-up canopy or gazebo leg with a worm-drive hose clamp or strap through its two 14 x 3.5 mm band tunnels. It adds a ribbed tab with a 10 mm hole for a guy line or sandbag, so wind load goes to the ground and not into the plastic corner joints that tend to snap. The V seats round legs from 19 to 32 mm and 25 mm square legs set corner-in. The block is 56 mm tall and 36 mm wide, and the tab reaches 67 mm.
Flagged: lifting or tensioned load. Not for safety-critical use without independent engineering review.
M3 Screw-Ear Small Tubing Clamp Trio
A set of three split-ring clamps for small tubing, with 6.5, 9 and 11 mm bores, joined on a snap-off sprue bar. Each one closes with an M3 bolt through a 3.4 mm clearance hole into a captured M3 nut pocket (5.7 mm across flats), so you can squeeze silicone, vinyl or air-line tubing tight onto barbs without hunting for tiny worm-drive clips.
Flexure Hose Pinch-Off Clamp M5
This one-piece flexure clamp pinches a coolant, fuel or vacuum hose shut while you swap a hose clamp or a part. The two smooth jaws are 8 x 14 mm and have 88 mm of usable length, enough for hoses up to about 45 mm OD laid flat. One M5 x 40 bolt runs through 5.5 mm holes and threads into a captured M5 hex nut pocket to close the 10 mm jaw gap, and a 2.5 mm living-hinge loop opens the jaws again when you loosen the bolt.
Flagged: automotive electrical. Not for safety-critical use without independent engineering review.
Tension Pole Caddy Replacement Shelf
A 120 x 90 mm draining shower shelf that replaces a cracked or lost tray on a corner tension-pole shower caddy. Instead of a moulded collar sized to one pole, it has a 90° V-saddle that seats any pole from 22 to 30 mm. Two worm-drive hose clamps (bands up to 12.7 mm wide) run through 14 x 3.2 mm tunnels in the 62 mm tall clamp block and hold it in place. The floor has drain slots, two gussets carry the shelf load into the clamp block, and the front lip is lowered so bottles lift out easily.
Round Tube Gate Latch Adapter Saddle
A V-saddle that clamps onto a round metal or PVC gate tube from 19 to 45 mm OD, including 3/4 in EMT (23.4 mm), 1 in PVC (33.4 mm), 1-3/8 in (34.9 mm) and 1-5/8 in (41.3 mm) chain-link frame tube. It's held with two 1/2 in worm-drive hose clamps threaded through built-in band tunnels, and gives you a flat 56 x 64 mm face you can screw a wood-gate drop or slide latch onto. That way the latch doesn't need a flat wooden rail. Mount the latch between the two bands with screws up to 16 mm long, or no longer than 10 mm on the side wings.
Heated Towel Rail V-Block Wall Bracket
A wall standoff bracket for ladder-style heated towel rails whose own clip has snapped. A 90° V-block self-centres any upright tube from 20 to 32 mm diameter, and a worm-drive hose clamp or heavy zip tie (bands up to 14 mm wide) through the slot behind the V pulls the tube tight. The bracket holds the tube centre 59–68 mm off the wall, is 70 x 57.5 x 32 mm, and screws up with four #8/#10 or M5 wood screws through 5.5 mm holes. Electric rails run warm, so print it in PETG or ASA rather than PLA.
Worm-Drive Hose Clamp Standoff Saddle
A screw-down V-saddle that raises a coolant, fuel, vacuum or bilge hose (about 15–40 mm OD) 18 mm off a vibrating firewall or hull. A standard worm-drive band clamp up to 13 mm wide, or a zip tie, passes through a 14 x 3 mm tunnel and wraps over the hose, so the clamp holds the hose in the saddle and never rubs on the panel. The base is 90 x 28 mm with two 5.5 mm holes for M5 or #10 screws.
Flagged: automotive electrical. Not for safety-critical use without independent engineering review.
Clamp-On Hair Dryer Concentrator Nozzle
Replacement concentrator nozzle for a hair dryer or heat gun with a round barrel of about 52–56 mm, which replaces a lost or cracked OEM snap-on. The 54 mm slotted collet sleeve is tightened by a hose clamp or zip tie in the recessed band seat, and it narrows the airflow to a 66 x 9 mm oval slot about 80 mm from the barrel.
Twin-Band Downspout Wall Standoff
This is a wall-mounted standoff block for a gutter downspout. It measures 130 x 60 x 11 mm and screws on with two #10 or M5 screws (5.5 mm countersunk holes). Two 14 x 3.5 mm tunnels run through it for zip ties or 1/2 in (12.7 mm) worm-drive hose-clamp bands. The band wraps around the downspout, so one part fits 2x3 in (about 51 x 76 mm nominal), 3x4 in or any other profile, and it replaces the brittle vinyl straps that snap every winter.
Screw-Tension Band Clamp 60-68 mm
A T-bolt style band clamp that draws down evenly on anything 60–68 mm OD (2" PVC at 60.3 mm, 63 mm PE pipe, 2.5" dust hose, pond and irrigation hose) using one M5 x 50 bolt and a captured M5 nut in a 5.7 mm across-flats hex pocket. The 14 mm wide, 2.8 mm thick band has a smooth 68 mm bore with no screw slots or sharp tail, so it spreads load without gouging silicone hose the way an oversized worm-drive clamp does; thickened 9 mm end bosses keep the clamping pressure even and the whole 81 x 74 x 14 mm part prints flat with the hoop load in the XY plane.
Hose Clamp Size Sorting Tower
A stepped cone that sorts a jumbled bag of worm-drive hose clamps by size — drop each clamp over the top and it hangs on the first shelf too wide for it. Eight tiers at 64, 56, 48, 40, 34, 28, 22 and 16 mm diameter over an 84 mm tall tower, on an 82 mm flange with three 4.5 mm M4 clearance holes to bolt it to a bench or pegboard shelf. Hollow conical core keeps it to about 45 cm³ of plastic.
4 in Dust Hose Cam Lever Cuff
One-hand quick clamp for nominal 4 in flexible dust hose and tool ports: a 104 mm ID, 20 mm tall band with a 2.4 mm flexing wall and a print-in-place cam lever that draws the ears ~4 mm together, so it grips hose measuring 100–107 mm OD without a screwdriver. Replaces an expensive large-diameter worm clamp that kinks thin-wall hose; the spiral cam slot detents at the closed position and the lever pivots on a captured 5 mm pin.
Washer Drain Hose Standpipe Clamp
A split collar that clamps onto a 2 in Schedule 40 PVC laundry standpipe (60.3 mm OD) with one M3 x 30 screw and a captured M3 nut, plus a snap-in C-jaw that grips the washer's corrugated drain hose (30–35 mm OD) so it can't kick out of the pipe and flood the room. 113 x 68 x 22 mm, prints flat with no supports and no overhangs.