Heads up: many models on this page are AI-generated or uploaded untested. They may be misconfigured for the intended application — check the dimensions and tolerances, and verify or edit the model before printing or relying on it.*
Five-Slot Paint Brush Hang-Dry Wall Rack
A 170 x 55 mm wall shelf that holds five washed paint brushes upright with the bristles hanging down so they drip-dry without bending. Its open-front slots are 10, 13, 16, 19 and 22 mm wide to fit thin artist brushes up to thick 3 in trim brushes. It mounts with two #8 wood screws through 5 mm holes 68 mm apart, and gussets between the slots carry the load.
Food Processor S-Blade Safety Dock
A 150 mm round dock that holds a loose food processor S-blade or chopper blade upright. The blade drops onto a tapered centre post (22 mm at the base, 11 mm at the tip, 52 mm tall), so it wedges and centres any hub with a bore between 11 and 22 mm. A 42 mm high, 2.4 mm wall surrounds blades up to 140 mm across, and six 4 mm radial drain slots let a freshly washed blade drip dry in the cupboard.
Flagged: contact with food. Not for safety-critical use without independent engineering review.
Wall-Mount Bath Mat Drying Saddle Rack
An open-grid saddle that screws to the wall. You fold a damp bath mat or hand towel over it so air reaches both sides, instead of leaving it soaking on the tub edge. It is 120 mm wide with a 100 mm reach and a 26 mm rear-curl lip so the mat stays put. Three gusseted fins carry the load in the layer plane, and it mounts with four #8 (4.2 mm) wood screws through 4.8 mm clearance holes set below the arm so a screwdriver can reach them.
Piping Tip Cone-Peg Drying Rack
A 110 x 144 mm tray with 12 hollow tapered pegs that hold decorating piping tips upright while they dry and while they're stored. Each peg tapers from 24 mm to 8 mm over 32 mm, so tips of any brand or size slide down until they seat, and water drains through the open peg onto the counter.
Reusable Straw And Brush Drying Rack
This is a countertop rack for drying reusable straws. Ten straws stand upright on drain ribs, so their open ends never sit in water. A 13 mm-deep guide bar holds them straight. It has two 13.5 mm holes for 12 mm boba straws, four 9.5 mm holes for 8 mm straws and four 7 mm holes for 6 mm straws and cleaning brushes. The rack measures 130 x 45 x 90 mm and has a 5.6 mm-deep drip tray. Two 4.6 mm holes in the back wall take #8 screws if you want to mount it on the wall.
Twin Rubber Glove Drying Stand
A sink-side stand that holds a pair of dishwashing gloves upside down on two open cross-fin posts, so air reaches inside the gloves and they don't stay damp and start to smell. The tray is 140 x 75 mm and 14 mm deep with 2 mm walls to catch the drips. Each post is 146 mm tall and tapers from 52 mm to 32 mm across, which holds a glove cuff open without stretching it.
Over-Sink 8 mm Rod Drying Rack End Rail
This is one end rail for a roll-free over-sink drying rack. Print two and push seven 8 mm stainless rods (or 8 mm dowels cut to sink width plus about 30 mm) into the 8.3 mm sockets on 22 mm centres to bridge the sink. Each rail is 150 x 22 x 14 mm and rests on the sink rim. A 10 mm lip with a 45° chamfer drops inside the basin edge, so with one rail on each side the rack can't slide off. The rack lets you air-dry pans, colanders and produce right over the drain.
Pasta Drying Rack Hub For 8 mm Dowels
A six-arm top hub for a homemade pasta drying rack. It drops onto the end of a 3/4 in schedule 40 PVC mast (26.7 mm OD, 27.0 mm blind socket) and holds six 8 mm wooden dowels in 8.3 mm sockets, 28 mm deep. With 250 mm dowels you get a rack about 600 mm across. The hub is 92 mm across and 40 mm tall, and the socket roof is a 45° cone, so it prints without supports.
Flagged: contact with food. Not for safety-critical use without independent engineering review.
Bristle-Down Makeup Brush Drying Rack
A stand for the vanity counter or a wall that hangs up to five washed makeup brushes bristle-down, so water runs out of the bristles and doesn't soak the glue in the ferrule. Each tapered V-slot narrows from 15 mm to 4.5 mm, so any handle in that range slides in and wedges without needing a set size. The rack is 140 x 130 mm with a 60 mm vented foot. It prints flat on its back with no supports, and two 4.5 mm holes take #6 wood screws if you want it on the wall.
22 mm Tube Drying Rack Hinge Half
A split-clamp hinge half for folding laundry and gullwing drying racks with 22 mm steel tube. It clamps on with one M4 bolt and nut, so it can replace a snapped plastic wing hinge. Print two and flip one over: the half-height 12 mm knuckles interleave with a 0.5 mm gap and pivot on an M5 bolt through a 5.5 mm bore. The part measures 53 x 30 x 24 mm. Change T to 19 for 19 mm tube.
Three-Slot Cutting Board Drying Stand
A countertop stand that holds three cutting boards on edge so both faces air-dry and don't trap water. It has two open comb rails, 122 mm long and set 84 mm apart, joined by low cross bars. Each slot is 22 mm wide at the floor and flares to 34 mm at the top, so boards up to 20 mm thick drop in easily and lean back into the V.
Bottle And Jar Drying Peg Rack
A four-peg drying stand for water bottles, travel mugs, jars and baby bottles: a 150 x 96 mm open rib frame, 4 mm thick, carrying four 95 mm three-blade pegs that taper from 23 mm across at the base to 14 mm at the tip, so a narrow bottle neck drops deep while a wide jar mouth rests high. Pegs lean 10° outward so bottles clear each other and air reaches the inside, and the fully open deck lets every drip fall straight through onto the drainboard instead of pooling.