Heads up: many models on this page are AI-generated or uploaded untested. They may be misconfigured for the intended application — check the dimensions and tolerances, and verify or edit the model before printing or relying on it.*
Shower Chair Flex-Fin Draining Leg Tip
This is a replacement foot for shower chairs and bath benches. It fits round aluminium leg tubes from 22 to 26 mm OD, which covers both 7/8 in and 1 in tubes. Six angled flex fins grip the tube, and a centre drain hole with three underfloor channels lets water out of the leg. The foot is 48 mm across, 36 mm tall and has a 31 mm deep socket. It replaces the cracked brand-specific tips that medical suppliers sell for $8–12 each, and you can stick an anti-slip pad to the flat base.
Inverted Oil Bottle Drain-Down Coupler
This tapered double-cone coupler stacks an upside-down quart bottle of oil, coolant or ATF on top of another bottle so the last drops drain from one into the other. The top seat takes bottle necks from about 26 to 50 mm. The 18–30 mm ribbed spigot wedges into necks with an inner diameter of about 19–30 mm. Four ribs inside the seat and three outside the spigot leave air paths so neither bottle seals and glugs. The part is 86 mm tall with a 68 mm drip-lip flange and prints mouth-down without supports.
Flagged: automotive electrical. Not for safety-critical use without independent engineering review.
Two-Bay Kitchen Shears Wall Holster
A wall holster that holds kitchen shears blade-down in one bay, with a second narrower bay for a swivel peeler or probe thermometer. Each bay is 13.6 mm deep, and the shears bay is 45 mm wide. Slotted floors let rinse water drain out. The part is 90 x 19 x 100 mm and hangs from two #8 wood screws through 4.8 mm holes on 60 mm centres above the pockets.
Barbed Drain Hair Snake With Ring Grip
This is a flat barbed strip that you push down a clogged shower, tub or sink drain and pull back out with the hair caught on it. The working strip is 7 mm wide and 1.8 mm thick, and its 18 backward-hooked barbs reach out to 13.6 mm across. The whole tool is 172 mm long and ends in a 36 mm ring grip that also works as a hanging loop. Print it in PETG if you want more flex down tight bends; you don't need a plumber or a chemical drain cleaner.
Slotted 2-3 in Tub Overflow Cover Plate
This is a 92 mm round blank cover plate for a tub overflow. It replaces a cracked or discontinued trip-lever faceplate, or covers the hole after you switch to a toe-tap or lift-and-turn drain. Its slotted screw holes (5.5 mm wide, counterbored for pan heads) fit any screw spacing from 2 in (50.8 mm) to 3 in (76.2 mm). On the back, a 9 mm stand-off skirt with inlet notches at the bottom keeps the overflow path open. Print it in PETG, face-down.
2x4 Fence Rail Post Bracket
A U-channel hanger that screws to a fence post and holds a 2x4 rail on edge (38.1 x 88.9 mm lumber, 40 mm channel to allow for swollen treated wood). It's for fixing a fence section when the rail end has rotted or the bracket ear has snapped off. The 90 x 60 mm back plate takes four #10 or M5 screws in 5.5 mm holes. The 50 mm cheeks take #8 or M4 screws in 4.5 mm holes into the rail sides, and two 8 mm drain holes keep water from sitting in the channel.
Shower Drain Hair Catcher Dome
A 92 mm diameter, 30 mm tall slotted cone that sits over a standard round shower drain grate and traps hair on the outside where you lift it off and wipe it clean, instead of letting it braid into the trap. Thirty 2.6 mm slots pass the water, a 2.5 mm base ring keeps it from rocking, and the 5.5 mm centre bore drops over the grate's existing screw (M5, #8-32 or #10-24) so it cannot slide or float away; the 14 mm knob is the lift handle.
Clip-On Pot Rim Pasta Strainer
A hook-on straining shield that clamps over the rim of a 20–26 cm (8–10 in) pot so you can pour off pasta or vegetable water without a colander. A continuous 45° hook lip and 7 mm rim throat grab any rolled rim anywhere along its 117 mm arc, twelve 3.5 mm radial slots pass water but hold pasta, and a 26 mm thumb pad lets you press it down through an oven mitt while pouring. Overall 117 x 73 x 18 mm — print in PETG or PP for boiling-water contact.
Flagged: contact with food. Not for safety-critical use without independent engineering review.