Heads up: many models on this page are AI-generated or uploaded untested. They may be misconfigured for the intended application — check the dimensions and tolerances, and verify or edit the model before printing or relying on it.*
Faucet Base U-Wrap Drip Tray
A 150 x 100 x 10 mm horseshoe tray that slides in from the back around a single-hole faucet base up to 62 mm across. You don't have to take the faucet off to fit it. The splash and pump-bottle drips that run down the faucet stay in a 2 mm floor with drainage ribs, so the vanity top stays dry and a soap bar or toothbrush can sit on the ribs and dry out. A 3 mm collar sits around the faucet.
Mug Coaster With Spoon Rest Lobe
A desk coaster for mugs up to 91 mm across the base. The cup sits on eight raised radial ribs above a walled 2 mm drip well, and a 35 mm wide side lobe with spoon rails holds a wet teaspoon or tea bag so it doesn't end up on your papers. The whole piece is 168 x 96 x 6 mm, has a flat bottom and prints without supports.
Twin Rubber Glove Drying Stand
A sink-side stand that holds a pair of dishwashing gloves upside down on two open cross-fin posts, so air reaches inside the gloves and they don't stay damp and start to smell. The tray is 140 x 75 mm and 14 mm deep with 2 mm walls to catch the drips. Each post is 146 mm tall and tapers from 52 mm to 32 mm across, which holds a glove cuff open without stretching it.
Electric Toothbrush Head Drip Stand
A 106 x 32 x 34 mm stand that holds four spare electric toothbrush heads upright in tapered seats (about 10 mm at the bottom, 18 mm at the top), so stems of different sizes all sit in it. Water drips into a separate cell under each head, and a 16 x 17 mm window at the front of each cell lets you wipe it out, so heads don't sit in standing water.
Hot Glue Gun Nose-Rest Drip Tray
A 170 x 100 mm walled drip tray for a full-size or mini hot glue gun. The gun lies on its side, and a 90° V-cradle holds the plastic nose collar. The cradle is 22 mm wide at the top, so the hot metal tip hangs about 19 mm above the floor in an open drip zone and never touches the print. A rear rack holds spare sticks: three 12.5 mm wells for 11 mm full-size sticks and three 8.5 mm wells for 7 mm mini sticks.
Ribbed Toilet Plunger Drip Tray
A round drip tray, 170 mm across and 22 mm tall, for a standard cup or flange toilet plunger. Eight radial ribs hold the rubber cup 8.4 mm above the floor, so air can dry it and water drains into the well instead of pooling on the floor tiles.
Twin-Notch Stovetop Spoon Rest
A 140 x 90 mm stovetop spoon rest with two separate drip wells, 12 mm deep. At the back is a 30 mm tall upright with two 16 mm U-notches, so two spoons, ladles or spatulas can rest by their handles with the heads down in the wells. Sauce drips into the well instead of onto the hob, and the divider keeps tomato and custard spoons apart.
Safety Razor And Shave Brush Stand
A countertop wet-shaving stand that hangs a safety razor and a shave brush bristles-down over a 96 x 56 mm drip tray, so both dry properly and the water lands in the tray instead of on the vanity. The razor fork takes handles from 9–20 mm and catches any head wider than ~30 mm; the brush fork tapers 38 mm down to 24 mm so it wedges on almost any handle, with the razor hook at 128 mm and the brush hook at 112 mm above the tray. Two 4.5 mm holes at 52 mm centres let you screw it to a wall or cabinet side with #8 (4.2 mm) screws instead.