Heads up: many models on this page are AI-generated or uploaded untested. They may be misconfigured for the intended application — check the dimensions and tolerances, and verify or edit the model before printing or relying on it.*
Cube Tissue Box Wall Cradle
A screw-to-the-wall cradle for a standard cube tissue box. It replaces a cracked acrylic holder or a box that keeps sliding off the vanity. Box size isn't standardised, so measure yours: the pocket is 122 mm wide and 120 mm deep, sized for cube boxes up to about 120 mm square. The open sides and the 80 mm hole in the floor let you push the box up and out. Two 4.5 mm holes, 80 mm apart, take #8 or M4 screws. The part is 128 x 126 x 70 mm.
Shower Arm Clamp-On Handheld Shower Cradle
A tapered cradle for a handheld shower head that clamps onto a straight, horizontal 1/2 in shower arm (21.3 mm OD, 22 mm bore), so you don't need to drill the tile. The cone tapers from 19 to 31 mm ID to fit most handles, a 16 mm front slot lets the hose slip in, and one M4 x 30 screw and nut pinch the clamp tight. Slide it onto the arm before you screw the diverter back on.
Bathroom Scale Wall Storage Cradle
A wall-mounted cradle that holds a bathroom scale upright on its edge, off the floor. It fits any scale up to 32 mm thick in a 34 mm wide channel with a 22 mm retaining lip. Screw two cradles to the wall about 150–250 mm apart with #8 wood screws: the 4.8 mm clearance holes are countersunk so the heads sit flush. The part is 45 × 99 × 40 mm, with a braced, lightened gusset under the floor. It prints on its side, so the scale's weight loads it along the layers, not across them.
Twin Wine Bottle Counter Cradle
This rack holds two standard 750 ml wine bottles on their side on a counter, pantry shelf or fridge shelf. Each cradle is a 40 mm radius arc: bottles 70–80 mm across settle into it, and bottles up to about 90 mm (sparkling wine) sit on the arc edges. It measures 176 x 42 x 55 mm and is a hollow frame with 2.4 mm walls, like an aluminium extrusion, so it stays light. It prints standing on its end with no supports, so the bottle's weight presses along the layers rather than trying to peel them apart.
21700 Three-Cell Strap-Down Cradle
A strap-down cradle for three 21700 cells lying side by side. It's for power banks, e-bike packs and high-drain flashlight builds, where almost every printed holder is sized for 18650s. It has two 22.4 mm saddles on a 25 mm pitch, so 21.0–21.7 mm cells drop in with 2.6 mm walls between them. The open ends take cells of any length, including 76 mm protected cells. Slots for a 20 mm hook-and-loop strap and four 4.5 mm M4 holes are on a 108 x 60 mm base.
Flagged: battery or DC power. Not for safety-critical use without independent engineering review.
18650 Three-Cell Pack Cradle
A cradle chassis for building a 3S (or 3P) 18650 pack: three 18.9 mm teardrop bores on 21.5 mm centres hold the cells in two 8 mm end collars plus a mid saddle, leaving both terminals flush with the outer faces at exactly 65 mm so nickel strip can be welded straight across. 82 x 68 x 34 mm, with raised + / − polarity ribs above each bore alternating for series wiring, four 3.4 mm M3 clearance holes to bolt the pack into a project, and four 12 x 5 mm zip-tie slots through the 3.5 mm base.
Flagged: battery or DC power. Not for safety-critical use without independent engineering review.