Heads up: many models on this page are AI-generated or uploaded untested. They may be misconfigured for the intended application — check the dimensions and tolerances, and verify or edit the model before printing or relying on it.*
8 mm Rod Pull-Out Closet Valet Bracket
A side-mount bracket that turns a length of 8 mm steel rod into a pull-out closet valet rod for staging tomorrow's outfit or the dry-cleaning. You screw the 130 x 40 mm plate to the inside of a wardrobe or cabinet side panel with four #8 wood screws, using 4.8 mm slots that let you shift it 8 mm front to back. The rod runs in a 130 mm long 8.3 mm slip bore, and an M3 screw driven into a 2.6 mm self-tap hole sets the drag, so the rod stays wherever you leave it.
Mid-Span Sagging Shelf Truss Bracket
This truss bracket screws to a stud under the middle of a sagging closet or pantry shelf and lifts the sagging span. The wall leg is 126 mm tall and the arm is 150 mm deep. Two 4.6 mm holes in the wall leg take #8 (4.2 mm) wood screws, and two 4.0 mm holes in the arm take #6 (3.5 mm) screws up into the shelf. A 9 mm bore through the diagonal brace gives a driver a straight path to the upper wall screw. The part prints flat on its side, so the shelf load runs along the layers instead of across them.
Bow-Spring Bypass Closet Door Floor Guide
This floor guide replaces the snapped plastic guide on a pair of bypass closet doors. It has two 47 mm channels on either side of an 8 mm centre divider, which sits in the gap between the doors. A flexible 1.8 mm bow spring in each channel holds any door from 35 to 45 mm thick (1-3/8 in and 1-3/4 in doors) without rattling. Fix it with #8 screws (4.2 mm shank) through 5 x 12 mm slots so you can slide it to line up with any track. It is 146 x 50 x 30 mm, the gusseted walls take the side load, and the doors need at least 5 mm of clearance above the floor.
Closet Rod Four-Hanger Cascade Drop Bar
This drop bar hooks straight over a closet rod and hangs four clothes hangers in a vertical cascade, so one spot on the rod holds four shirts. The 40 mm open hook fits 1-1/4 in (31.75 mm) and 1-3/8 in (35 mm) closet rods. The 22 x 6 mm bar is 177 mm tall overall, and its four 11 mm holes take wire or plastic hanger hooks up to about 10 mm thick. It prints flat, so the hanging load runs along the layers and can't split them apart.
Closet Rod Snap-On Belt And Tie Hanger
A belt, tie and scarf hanger with eight upturned hooks. Its C-ring snaps onto a 1-5/16 in (33.3 mm) wood closet rod or a 1 in schedule-40 PVC rod (33.4 mm OD). The 33.8 mm bore has a 31 mm snap mouth so the hanger turns freely on the rod but won't get knocked off. The part is 65 x 167 x 8 mm and prints flat, so belt loads bend the hooks along the layers rather than across them.
Wire Shelf Snap-In Back Wall Clip
A screw-on replacement for the cracked wall clip on ClosetMaid-style wire shelving. The back wire drops into a 7 mm channel and snaps past a 5.5 mm flexing lip, so it fits back wires about 5.5–7 mm thick (measure yours). The clip is 13 x 58 x 20 mm and fixes to the wall with two countersunk 5.5 mm holes for #8/#10 wood screws or M5. It prints on its side, so shelf load runs along the layers, and a 45° gusset under the channel floor carries it.
Bifold Door Bottom Pivot Bracket
Replacement bottom pivot bracket for hollow-core bifold closet doors, where the original steel bracket is lost or bent and the store only sells the whole track kit. A 6.8 mm x 13 mm deep blind socket takes the standard 1/4 in (6.35 mm) spring-loaded bottom pivot pin and sits 20 mm out from the jamb face; the 62 x 38 x 5 mm base screws to the floor through two 4.6 x 18 mm slots (#8 wood screws) for in/out gap adjustment, and the 30 mm jamb tab takes two #10 screws through 5.5 mm holes on 20 mm centres, braced by two gussets.