Heads up: many models on this page are AI-generated or uploaded untested. They may be misconfigured for the intended application — check the dimensions and tolerances, and verify or edit the model before printing or relying on it.*
Sump Pump Float Cord Zip-Tie Pipe Clamp
Replaces the small plastic clip that snaps off and lets a tethered float switch cord slide down the sump discharge pipe. A 90° V-saddle seats any pipe from 1-1/4 to 2 in (42–60 mm OD), and two zip-tie tunnels lock it to the pipe. A 10 mm top groove with two more tunnels grips float cords up to about 9 mm, so you can set the tether length by sliding the cord before you cinch it. The clip is 40 x 60 x 40 mm and takes standard ties up to 4.8 mm wide.
Chain-Link Gate Wheel Clamp Fork
This bolt-on wheel fork for swing gates clamps around the 1-3/8 in (34.9 mm OD) vertical frame tube of a chain-link gate. Two M5 pinch bolts close it on the tube, and captive-nut pockets hold the nuts. It carries a caster wheel up to 32 mm wide on an 8 mm steel pin. There are two axle heights: one for 50 mm (2 in) wheels and one for 76 mm (3 in) wheels. An M3 grub screw locks each pin. Use it to replace a rusted or cracked factory gate-wheel bracket without buying a whole wheel assembly.
Shower Arm Clamp-On Handheld Shower Cradle
A tapered cradle for a handheld shower head that clamps onto a straight, horizontal 1/2 in shower arm (21.3 mm OD, 22 mm bore), so you don't need to drill the tile. The cone tapers from 19 to 31 mm ID to fit most handles, a 16 mm front slot lets the hose slip in, and one M4 x 30 screw and nut pinch the clamp tight. Slide it onto the arm before you screw the diverter back on.
46-49 mm Chain-Link Brace Band
A clamp-on brace band for odd-size chain-link post pipe from 46 to 49 mm OD (1-7/8 in 47.6 mm pipe and 1-1/2 in 48.3 mm pipe), the sizes big-box stores don't stock. The 49 mm bore can tighten up to 8 mm around the post. A 9 mm cross-hole with a recessed square seat takes a standard 5/16 in carriage bolt to hold a rail-end cup or tension bar. The band is 25 mm tall with a 5 mm wall. Print it in PETG or ASA for outdoor use.
Spring-Fin P-Clamp For 18-24 mm Pipe
A one-piece P-clamp with a 29 mm split ring lined with five flexible spring fins. It grips 1/2 in EMT (17.9 mm), 1/2 in PVC (21.3 mm) or 3/4 in EMT (23.4 mm) without rattling, so you don't have to buy a box of 25 fixed-size clamps to get one odd size. Two 5.5 mm screw holes, 54 mm apart, take #8/#10 wood screws or M5 bolts into a stud or frame rail. Tightening the screw through the 14 mm wide strap closes the 4 mm tab gap and squeezes the ring onto the pipe. Thread the clamp onto the run before you fix it.
1 in PVC Snap-In Fence Standoff Clip
Snap-in saddle clip for 1 in schedule 40 PVC (33.4 mm OD). The pipe pushes through a 28 mm mouth into a 33.6 mm cradle, and the clip holds it 12 mm off a fence, post or wall so wood can dry behind the run. It suits irrigation, solar conduit and garden hoop runs. The 70 x 20 mm foot takes two #10 wood screws (5.3 mm clearance holes on 56 mm centres), and the ring prints flat so any pull on the pipe goes along the layers.
Dual Size EMT Conduit Snap Hanger
A screw-down wall plate with two snap-in saddles that take 3/4 in EMT (23.4 mm OD, 23.7 mm bore) and 1/2 in EMT (17.9 mm OD, 18.2 mm bore), so a conduit and a small pipe or hose run stacked on one anchor point. Overall 102 x 26 x 25.5 mm; two 4.5 mm holes 84 mm apart take M4 or #8 wood screws, the lips wrap past the pipe centreline for a 0.5 mm one-hand snap, and a dovetail tongue and socket on the ends let hangers gang into a continuous run along a wall or joist.
Chain-Link Gate Fork Latch
Replacement fork latch for a residential chain-link gate: a split collar clamps the 1-3/8 in (34.9 mm) gate frame upright with two M5 bolts, and a tapered V-fork reaches 72 mm across to self-centre on any 1-5/8 in to 2-3/8 in (41.3–60.3 mm) latch post. A 6.4 mm cross hole through both jaws takes a 6 mm pin, hitch clip or padlock shackle so the gate can be locked shut. Overall 129 x 62 x 26 mm; print in PETG or ASA for UV life.
Pipe Clamp Stabilizer Foot
A drop-on foot for 3/4 in schedule-40 black pipe clamps (26.7 mm OD bar), sized with a 27.2 mm U-channel so the clamp stands upright on the bench instead of rolling over during a glue-up. The 50 x 86 mm base gives a wide anti-tip stance, twin 12 mm shoulder pads at 48 mm hold the workpiece 4.4 mm clear of the bar so squeeze-out never reaches the steel, and a 3.4 mm side hole takes an M4 self-tapping set screw to lock the foot at any point along the pipe. Print two (or four for long bars).