Heads up: many models on this page are AI-generated or uploaded untested. They may be misconfigured for the intended application — check the dimensions and tolerances, and verify or edit the model before printing or relying on it.*
Chain-Link Gate Wheel Clamp Fork
This bolt-on wheel fork for swing gates clamps around the 1-3/8 in (34.9 mm OD) vertical frame tube of a chain-link gate. Two M5 pinch bolts close it on the tube, and captive-nut pockets hold the nuts. It carries a caster wheel up to 32 mm wide on an 8 mm steel pin. There are two axle heights: one for 50 mm (2 in) wheels and one for 76 mm (3 in) wheels. An M3 grub screw locks each pin. Use it to replace a rusted or cracked factory gate-wheel bracket without buying a whole wheel assembly.
Privacy Screen Grommet Snap S-Hook Set
A sprue of five flat-printed S-hooks that hold privacy-screen or windscreen grommets onto chain-link fence. They replace the brittle factory clips that snap or blow away. One end has a 4.8 mm wire seat with a 2.8 mm snap throat, which fits 11.5–9 gauge (2.9–3.8 mm) fence wire, vinyl-coated included. The other end has a 6 mm grommet hook with a 3.6 mm snap throat that passes through grommets 8 mm and larger. Each hook is 42 x 20 x 6 mm and is drawn in the XY plane, so the pull runs along the layers and not across them.
Chain-Link Top Rail End Cup 1-3/8 And 1-5/8
This is a single replacement rail end cup for chain-link fence. It uses a stepped bore that takes either a 1-5/8 in (41.3 mm OD) top rail in the 41.9 mm outer section or a 1-3/8 in (34.9 mm OD) rail in the 35.5 mm inner section. The 26 x 6 mm tongue has a 10 mm hole that fits a 5/16 in or 3/8 in carriage bolt and seats in a standard brace band, so you can fix one rusted or snapped cup without buying a 10-pack. Two 4.2 mm radial holes take a #8 screw to lock the rail in place. The cup is 48 mm across and 100 mm tall, and should be printed in PETG or ASA for outdoor use.
Round Tube Gate Latch Adapter Saddle
A V-saddle that clamps onto a round metal or PVC gate tube from 19 to 45 mm OD, including 3/4 in EMT (23.4 mm), 1 in PVC (33.4 mm), 1-3/8 in (34.9 mm) and 1-5/8 in (41.3 mm) chain-link frame tube. It's held with two 1/2 in worm-drive hose clamps threaded through built-in band tunnels, and gives you a flat 56 x 64 mm face you can screw a wood-gate drop or slide latch onto. That way the latch doesn't need a flat wooden rail. Mount the latch between the two bands with screws up to 16 mm long, or no longer than 10 mm on the side wings.
1-3/8 in Top Rail Chain-Link Snap Tie
A tool-free, reusable tie that snaps over a standard 1-3/8 in (34.9 mm) chain-link top rail. It replaces the twisted wire ties that rust and work loose. The 35.4 mm C-ring wraps 240° around the rail, and a flexing 4 mm hook on the side snaps over one strand of 9–11 gauge mesh wire (3.0–3.8 mm) to hold the fabric tight against the rail. The clip is 14 mm tall and prints flat with no supports.
46-49 mm Chain-Link Brace Band
A clamp-on brace band for odd-size chain-link post pipe from 46 to 49 mm OD (1-7/8 in 47.6 mm pipe and 1-1/2 in 48.3 mm pipe), the sizes big-box stores don't stock. The 49 mm bore can tighten up to 8 mm around the post. A 9 mm cross-hole with a recessed square seat takes a standard 5/16 in carriage bolt to hold a rail-end cup or tension bar. The band is 25 mm tall with a 5 mm wall. Print it in PETG or ASA for outdoor use.
Flex-Fin Chain-Link Post Cap 57-63 mm
This rain cap replaces a missing or rusted cap on a 2-3/8 in (60.3 mm OD) chain-link terminal post or a 60 mm metric round post. Eight angled flex fins grip any post from 57 to 63 mm OD, so an odd-size or out-of-round tube still gets a snug cap. The cap is 76 mm across with a drip lip and a 32 mm skirt. A 4.5 mm side hole takes a #8 self-drilling screw to lock the cap in place against wind and theft.
Chain-Link Gate Fork Latch
Replacement fork latch for a residential chain-link gate: a split collar clamps the 1-3/8 in (34.9 mm) gate frame upright with two M5 bolts, and a tapered V-fork reaches 72 mm across to self-centre on any 1-5/8 in to 2-3/8 in (41.3–60.3 mm) latch post. A 6.4 mm cross hole through both jaws takes a 6 mm pin, hitch clip or padlock shackle so the gate can be locked shut. Overall 129 x 62 x 26 mm; print in PETG or ASA for UV life.