Heads up: many models on this page are AI-generated or uploaded untested. They may be misconfigured for the intended application — check the dimensions and tolerances, and verify or edit the model before printing or relying on it.*
1 in Towel Bar Tapered Spring-End Cap
This is a replacement end cap for 1 in (25.4 mm) round towel bars that spring into ceramic or tile wall posts. Six crush ribs inside the 26 mm socket grip bars from about 24.6 to 25.6 mm. A tapered nose (13 to 21 mm) centres itself in round post sockets of roughly 15–21 mm, and a 9 mm by 14 mm well holds a compression spring up to about 8.5 mm OD. It replaces the cracked plastic bushing so you don't have to buy a whole replacement bar kit. The part is 31 mm across and 47 mm tall.
Towel Bar Drywall Load-Spreader Plate
This 140 x 76 mm wall plate goes behind a towel bar, TP holder or robe hook post that keeps pulling out of drywall. It spreads the load across eight countersunk #8 (4.2 mm) screw holes, so you can use anchors or catch a stud. The hardware's bracket bolts to the raised 8 mm cross with M4 screws. The M4 nuts sit in hidden 7.3 mm channels on the wall side, and 4.5 mm slots let the bolts land anywhere within ±25 mm both horizontally and vertically, so it fits almost any bracket spacing.
Square Towel Bar End Post Replacement
A replacement square-style towel bar end post that screws straight to the wall with two #8 screws, so you can keep your bar when the original post snaps off. The 19.6 mm blind socket takes 3/4 in (19.05 mm) round bars, and an M4 set screw in a heat-set insert also clamps 5/8 in (15.9 mm) bars. It holds the bar centre 50 mm off the wall. Print one, then flip it over to use it on the other end.
Swing-Out Towel Arm Hub For 1/2 in PVC
A wall-mounted swivel towel arm that prints in place with its hinge already assembled. It is a 52 x 52 mm wall plate with four 5 mm holes for #8 screws, and a 28 mm hub that turns on a 12 mm pin. The hub has a 21.6 mm socket, 32 mm deep, for 1/2 in schedule 40 PVC (21.3 mm OD) cut to any length, and a #6 screw hole pins the pipe in place. Cone-shaped bearing faces and 0.5 mm gaps let the hub swing about 90° either way, so a drying towel folds flat against the wall.
Slotted Towel Bar Old-Hole Cover Rosette
A 100 mm diameter, 4 mm thick rosette plate that sits behind a new towel-bar or grab-bar mounting flange and hides the holes left by an older, wider bar. It has four radial 4.8 mm slots that take #8 or #10 wood screws (4.2 mm / 4.8 mm shank) at any spacing from 20 to 76 mm, horizontal or vertical. It prints face-down so the show side comes out smooth, and it can be painted to match the wall.
Three-Size Tile Drill Guide With Water Cups
A 120 x 50 mm drill guide that you tape to glazed wall tile so the bit doesn't skid when you drill holes for towel bars, grab-bar anchors, shower caddies or toilet-roll holders. It has three 22 mm tall guide towers for 6, 8 and 10 mm tile or glass bits (bores 6.3, 8.3 and 10.3 mm). Each tower has a water cup on top that drips coolant down the bore to the bit tip, and V-notches on both edges line each tower up with your pencil crosshair.
Shower Rod Double Rod Clamp
A pinch-clamp bracket that grips a 1 in (25.4 mm) shower curtain tension rod — 25.6 mm split bore, one M4 bolt with a captured M4 nut — and carries a second rod 62 mm away in a 27.0 mm bore sized for 3/4 in schedule-40 PVC (26.7 mm OD). Print two: they add a liner rod inside the shower or a drying bar for wet towels outside, with no holes in the tile. 110 x 35 x 20 mm, printed flat so the hanging load bends the arm within the layer plane.
Dual Size Towel Bar Bracket
Replacement wall-end bracket for a broken towel bar, with a stepped socket that takes both 1 in (25.4 mm) and 3/4 in (19 mm) tube — a 1 in bar bottoms on the step after 18 mm, a 3/4 in bar slides 28 mm deep — and an M4 set screw that locks it so you don't have to replace the whole rail set. Back plate is 42 x 68 x 6 mm with two counterbored 4.5 mm holes 52 mm apart for #8/M4 anchors, bar centre stands 38 mm off the wall, overall 55 mm tall.