Heads up: many models on this page are AI-generated or uploaded untested. They may be misconfigured for the intended application — check the dimensions and tolerances, and verify or edit the model before printing or relying on it.*
Sink Plug Parking Peg With Chain Notch
A wall-screwed peg that holds a loose sink or bath plug off the basin. The 25 mm peg with its 18 mm up-turned lip holds the plug, and a 3 mm notch in the lip catches the bead chain. The 30 x 75 mm plate takes two 4.5 mm countersunk holes for #6/#8 wood screws or M4, and a 45° rib under the peg carries the load across the layers.
Motorcycle Helmet Wall Hook With Jacket Hook
A garage wall hook that holds a motorcycle or bike helmet on a 112 mm arm with a raised lip so the helmet can't slide off. A short hook underneath takes a jacket or gloves. It mounts on a stud with two countersunk #10 or M5 screws through 5.5 mm holes. It prints on its side, which puts the load in the layer plane, and the 45° trussed gusset keeps it stiff with about 90 cm³ of plastic. Overall size is 112 × 135 × 24 mm.
Print-In-Place Gravity-Stow Folding Wall Hook
This print-in-place folding hook has a 120 x 44 x 10 mm wall plate. An 80 mm hook arm hangs flat in a window cut through the plate, so gravity keeps it stowed. When you need it, swing it out: it pivots on a 5 mm printed pin and stops a little past horizontal against the plate. That makes it useful in hallways, vans and closets where a fixed hook would snag you. The two 4.6 mm countersunk holes take #8 wood screws (4.2 mm shank) or M4 screws.
Stand Mixer Attachment Wall Hook Rack
A 150 x 62 mm wall or cabinet-door rack with three rising 12 mm hook fins that hang a stand mixer's flat beater, whisk and dough hook by their open frames, with an 8 mm lip that keeps them from sliding off. It mounts with two #8 wood screws (4.8 mm clearance holes, 50 mm apart). It prints upright with the fins doubling as feet, so the hook arms take load inside the layers.
Ironing Board Twin-Hook Wall Hanger
A wall hanger for a folding ironing board: it screws to the wall and has two gusseted J-hooks, 100 mm apart overall, that catch the board's folded leg crossbar. Each hook has a 35 mm deep throat and an 18 mm lip, so leg tubes up to about 30 mm fit. It prints on its side, so the weight pulls along the layers instead of peeling them apart. Three 4.5 mm holes take #8 wood screws or M4 bolts.
Ear Muff And Safety Glasses Wall Hanger
A screw-on wall hanger for hearing protection and eye protection by the saw or grinder. The top saddle is 41 mm deep with an 8 mm lip, sized for an ear-muff headband. The lower hook is 26 mm deep and takes folded safety glasses. It is 135 mm tall and 36 mm wide, and fixes with two #8 wood screws (4.8 mm clearance holes, 9 mm counterbores). It prints on its side so the hook bending load runs along the layers, not across them.
Jumper Cable And Charger Clamp Wall Dock
A screw-to-stud wall dock for jumper cables or a battery charger. The coil hangs in a saddle 62 mm deep, the red clamp grips a 6 mm top tab and the black clamp grips the 8 mm saddle lip, so the cables stop living in a tangled pile on the floor. It's 68 x 112 x 48 mm and prints on its side, which keeps the hanging load in the layer plane. Two horizontal 5.5 mm holes with 10 mm counterbores take #10 (4.8 mm) or #8 wood screws, or M5 bolts.
Flagged: battery or DC power. Not for safety-critical use without independent engineering review.
Vertical Bike Wall Hook With Rim Saddle
Screw-on J-hook that hangs a bike vertically by its front wheel. The rim's spoke bed rests in a curved saddle 85 mm out from the wall, behind a lip 24 mm tall. It mounts to a stud with two #10 (4.8 mm) or M5 screws through countersunk 5.5 mm holes 105 mm apart. The part is 104 x 140 x 22 mm and prints on its side, so the bending load runs along the layers instead of across them.
Screw-On Ladder Rail Wall Hook
A heavy wall hook for hanging a ladder flat on the garage wall. It has a 92 mm deep cradle and a 32 mm retaining lip, so the side rail of a stepladder or a nested extension ladder drops in and can't roll out. Print two and fix each to a stud with #10 (4.8 mm) screws through 5.5 mm holes. It prints on its side, 150 x 112 x 22 mm, so the weight loads along the layers and the tapered truss arm keeps the plastic volume down.
Screw-On Curtain Tieback Holdback Hook
A curtain holdback that screws to the wall or window trim. Two #8 wood screws (4.2 mm shank) go through 4.6 mm clearance holes, 48 mm apart, with 8.5 mm counterbores for pan heads. A 51 mm deep cradle with an 18 mm lip holds a gathered drape open. The hook stands 64 mm tall, reaches 65 mm from the wall and is 16 mm wide. It prints on its side, so the curtain's weight runs along the layers instead of peeling them apart, and a gusset under the arm stops it drooping.
Cast Iron Skillet Handle-Hole Wall Hook
A gusseted wall hook for hanging a cast iron skillet or griddle by its handle hole. The tip is 14 x 12 mm, so it goes through any handle hole at least 15 mm across. The arm gives 56 mm of reach and ends in a 12 mm up-lip that keeps the pan from sliding off. The hook prints on its side, so the pan's weight bends it along the layers rather than across them. It mounts through the 90 mm tall back plate with two #8 (4.2 mm) pan-head wood screws in 5 mm clearance holes.
Fork-Cradle Shower Squeegee Wall Hanger
This screw-on wall hanger holds a shower squeegee on two forked arms. The handle drops through a 22 mm gap, and the blade sits in a 34 mm-deep cradle with a lip that stops it sliding off. It takes handles up to 22 mm thick. The part measures 45 x 70 x 46 mm and fixes to the wall with two #8 wood screws or M4 screws through 4.6 mm holes that are 50 mm apart. It prints on its side, so the arms carry the load along the layers and not across them.