Heads up: many models on this page are AI-generated or uploaded untested. They may be misconfigured for the intended application — check the dimensions and tolerances, and verify or edit the model before printing or relying on it.*
Tub Lip Screw-Clamp Draining Soap Ledge
A drill-free soap and razor ledge that clamps over the rim of a freestanding, clawfoot or drop-in tub. An M5 screw runs through a captured nut and closes on any rim from about 4 to 38 mm thick, with a 30 mm deep jaw. The 56 x 70 mm tray drains through twelve 4 mm holes, has a 15 mm front lip, and two gussets carry the load into the inner jaw. It prints flat on its side, so the clamp loads stay in the layer plane.
M5 Screw-Clamp Desk Mat Edge Anchor
This C-clamp holds the front edge of a desk mat or mouse pad down so it stops sliding and curling. It fits desk tops up to about 40 mm thick with no holes drilled. An M5 bolt goes up through the lower jaw into a drop-in M5 hex nut pocket (8.4 mm slot) and presses on the underside of the desk. The 7 mm upper jaw reaches 35 mm in to pin the mat, and the throat is 45 mm. The part prints on its side, so the clamp load runs along the layers.
Shelf-Pin Mount 1/2 in EMT Rod Cup
This rod cup lets you add a hanging rail to a wardrobe or cabinet without drilling. It pins into the shelf-pin holes the cabinet already has. A 18.4 mm U-cup takes 1/2 in EMT conduit (17.9 mm OD), and two 5 mm steel pins or dowels, each 16 mm long, go through the 6 mm plate into the side panel. The lower hole is round. The upper hole is a slot that fits hole spacings of 1 in, 1-1/4 in and 32 mm. There is also a 4.5 mm hole for a #6 screw if the cabinet has no shelf-pin holes. Print two and cut the EMT to the inside width of the cabinet minus 13 mm.
1-1/4 in Grab Bar Saddle Soap Dish
This soap dish snaps onto a standard 1-1/4 in (31.75 mm) shower grab bar, so you don't have to drill new holes in the tile. The clip has a 32.2 mm bore and wraps 240° around the bar at both ends. The ribbed 72 x 80 mm tray sits directly above the bar, so the soap's weight doesn't twist it. Six drain slots let water run straight down onto the bar.
Door Gap Resistance Band Anchor
A no-drill T-shaped anchor that goes through the hinge-side gap of a closed door. It lets you clip resistance bands or a carabiner to any door without screwing anything into the frame. The 2.4 mm thick, 40 mm tall tongue passes through the gap. A 40 x 10 mm stop bar bears on the far side of the door and jamb, and an 18 mm eye on your side takes the band. The tongue reach clears doors up to 48 mm thick, and the part prints upright so the pull runs along the layers instead of across them.
Picture Rail Moulding Hook
This hook replaces the old picture rail hooks used in period houses. You hang pictures, mirrors or plants from the moulding, so no nails go into plaster. It is 40 x 95 x 12 mm. A 3 mm tip drops 9 mm behind the moulding's top bead, and the 21 mm throat fits rails that stand up to about 20 mm off the wall. The wire hangs in a 6 mm cup at the bottom of a 5 x 12 mm stem. The part prints flat, so the hanging load runs along the layer lines rather than across them.
No-Drill Hanging File Rail Bracket
A hook-over saddle bracket (57 x 34 x 20 mm) that converts any plain desk or dresser drawer into a hanging file drawer with no drilling: it drops over the drawer side wall (5-20 mm thick, clamped by one M4 x 25 self-tapping screw from the outside) and carries an 8 mm smooth rod through an 8.3 mm slip-fit bore. The rod sits 17 mm inboard of the drawer wall and 9 mm below the rim, so letter/A4 folder hooks clear everything; use four brackets and two rods cut to the drawer's inside depth for a full file drawer.
No-Drill Gutter Lip Camera Clamp
A no-drill C-clamp that hooks over the front lip of a K-style rain gutter and carries a security camera or its solar panel on a 13 mm long 1/4-20 slot, so renters and anyone with aluminium soffits never touch the fascia. The 26 mm throat is closed by two M4 screws in 5.5 mm heat-set insert bores (use M4 x 30), gripping lips and beads from 5 to 24 mm deep; overall 74 x 44 mm with a 30 mm wide jaw, and it prints with zero overhangs because the whole profile is extruded along the gutter run.
Frameless Shower Door Saddle Hook
A clamp-on double hook that saddles the top edge of a frameless glass shower door — towel hook on the outside, loofah/razor hook on the inside, no drilling, adhesive or suction cup. The 13.6 mm slot with a raised grip pad takes 6–13 mm (1/4"–1/2") tempered glass, and an M4 heat-set insert (5.5 mm bore) plus an M4x16 screw locks it down; 76 x 43 x 26 mm.