Heads up: many models on this page are AI-generated or uploaded untested. They may be misconfigured for the intended application — check the dimensions and tolerances, and verify or edit the model before printing or relying on it.*
1/2 in EMT Curtain Rod Wall Bracket
A gusseted wall bracket for DIY industrial-style curtain rods made from 1/2 in EMT conduit (17.9 mm OD). The rod slips through an 18.4 mm bore and an M4 self-tapping set screw locks it in place. The bracket stands the rod 88 mm off the wall so it clears blinds and trim, and it fixes to the wall with two #8 wood screws through 5 mm holes. It prints on its side, so the rod's weight runs along the layers instead of across them. The bracket is 104 x 82 x 24 mm.
Trussed Hanging Planter Wall Arm
A trussed wall arm that sticks out 165 mm and holds hanging planters, wind chimes or lanterns from S-hooks in two 9 mm eyes, one 100 mm out from the wall and one 155 mm out. It prints on its side, so the weight pulls along the layers instead of across them, and it mounts to a stud with two #10 wood screws or M5 bolts through 5.5 mm holes on a 152 mm vertical spacing (part is 12 mm thick, 174 mm tall).
Towel Ring Screw-Closed Wall Post
This is a replacement wall post for a bathroom towel ring whose small retaining tab has snapped. The top of the ring drops into a 10 mm wide open-top cradle (fits ring wire or tube up to about 9 mm), and an M4 screw across the mouth locks it in. It mounts with two #8 pan-head wood screws through 4.8 mm holes 62 mm apart. It is 56 mm deep, 80 mm tall and 22 mm wide, and it prints on its side so the towel load runs along the layers, not across them.
Heated Towel Rail V-Block Wall Bracket
A wall standoff bracket for ladder-style heated towel rails whose own clip has snapped. A 90° V-block self-centres any upright tube from 20 to 32 mm diameter, and a worm-drive hose clamp or heavy zip tie (bands up to 14 mm wide) through the slot behind the V pulls the tube tight. The bracket holds the tube centre 59–68 mm off the wall, is 70 x 57.5 x 32 mm, and screws up with four #8/#10 or M5 wood screws through 5.5 mm holes. Electric rails run warm, so print it in PETG or ASA rather than PLA.
Fire Extinguisher V-Cradle Strap Bracket
A wall bracket with a V-shaped cradle that centres any fire extinguisher body from about 70 to 130 mm across, which covers typical 2.5 to 10 lb units. It replaces a cracked OEM strap bracket in a garage, RV, boat or kitchen. The plate is 140 x 42 mm, the arms reach out 50 mm, and it mounts with two #10 or M5 screws through 5.5 mm holes. A 25 mm hook-and-loop strap or 1 in webbing runs through the 27 mm slots at the arm tips. Measure your extinguisher body before you order. For vehicles, fit one near the top and one near the bottom of the body.
Ceiling Curtain Track Wall Standoff Arm
A trussed wall arm for mounting a ceiling-only curtain track on a wall. It stands 82 mm tall and is 22 mm wide, with a 110 mm arm. The track's own ceiling clip bolts to the underside of the arm with an M4 bolt and nut through one of four 4.5 mm holes at 66, 78, 90 or 102 mm from the wall, so you can choose how far the track sits out. The arm fixes to the wall with two 5.5 mm holes for #8 or #10 wood screws or M5 bolts, one above the arm and one below the diagonal strut, so a driver can reach both. It prints on its side, so the load runs along the layers rather than across them.
1/2 in EMT Pot Rail Wall End Bracket
Wall end bracket that holds a 1/2 in EMT conduit pot rail (17.9 mm OD, 18.4 mm socket, 20 mm deep) 55 mm off the wall, so pots and pans hang clear of the backsplash. It mounts with two #8 wood screws, has a braced gusset to carry the weight of heavy pans, and an M4 self-tapping set screw stops the rail from turning. Print a pair, one for each end of the rail.
Twin-Band Downspout Wall Standoff
This is a wall-mounted standoff block for a gutter downspout. It measures 130 x 60 x 11 mm and screws on with two #10 or M5 screws (5.5 mm countersunk holes). Two 14 x 3.5 mm tunnels run through it for zip ties or 1/2 in (12.7 mm) worm-drive hose-clamp bands. The band wraps around the downspout, so one part fits 2x3 in (about 51 x 76 mm nominal), 3x4 in or any other profile, and it replaces the brittle vinyl straps that snap every winter.
2x4 Lumber Rack Arm Socket
A wall bracket that turns a scrap 2x4 into a cantilever lumber-rack arm: the socket takes a nominal 2x4 end (38.1 x 88.9 mm actual) in a 39.2 mm channel, 71 mm deep, with 4.5 mm cheeks that pin the wood with two 5.5 mm cross screws per side. The 8 mm back plate takes four #10 or M5 screws into a stud on a 30 x 48 mm pattern, counterbored 3 mm so the heads clear the lumber. Overall 78 x 48 x 88 mm — print a pair per arm for conduit, moulding, pipe and offcut storage.