Heads up: many models on this page are AI-generated or uploaded untested. They may be misconfigured for the intended application — check the dimensions and tolerances, and verify or edit the model before printing or relying on it.*
3/4 in PVC Poultry Waterer Pipe Hanger
This screw-on hanger clamps a 3/4 in Schedule 40 PVC nipple-waterer pipe (26.7 mm OD) to a coop post or run frame. An M4 pinch bolt with a captive nut stops the pipe from rolling, so the nipples keep pointing straight down and don't drip. Vertical 5.2 mm slots fit #8 or #10 screws (4.2–4.8 mm shank) and give 5 mm of height adjustment for levelling the line. The part measures 62 x 80 x 16 mm and the pipe weight loads it along the layer plane.
Closet Rod Four-Hanger Cascade Drop Bar
This drop bar hooks straight over a closet rod and hangs four clothes hangers in a vertical cascade, so one spot on the rod holds four shirts. The 40 mm open hook fits 1-1/4 in (31.75 mm) and 1-3/8 in (35 mm) closet rods. The 22 x 6 mm bar is 177 mm tall overall, and its four 11 mm holes take wire or plastic hanger hooks up to about 10 mm thick. It prints flat, so the hanging load runs along the layers and can't split them apart.
Pi 4 Under-Shelf Drop Hanger
This bracket hangs a Raspberry Pi 4B/3B+ upright under a shelf or desk. Two slotted holes take #8 wood screws (4.2 mm shank) and give 5 mm of side-to-side adjustment. The board sits on 6 mm standoffs with M2.5 clearance holes on the 58 x 49 mm pattern, and three gussets brace the 94 x 75 mm plate against the 32 mm screw flange. The bracket also has a vent window and two zip-tie slots for the cables, and the USB and Ethernet end stays open.
Ironing Board Twin-Hook Wall Hanger
A wall hanger for a folding ironing board: it screws to the wall and has two gusseted J-hooks, 100 mm apart overall, that catch the board's folded leg crossbar. Each hook has a 35 mm deep throat and an 18 mm lip, so leg tubes up to about 30 mm fit. It prints on its side, so the weight pulls along the layers instead of peeling them apart. Three 4.5 mm holes take #8 wood screws or M4 bolts.
Shower Glass Over-Top Mirror Hanger
This hanger replaces a suction-cup shaving mirror by hooking over the top edge of a frameless shower screen. The glass slot is 10.5 mm, so it fits 6–10 mm tempered glass. A 100 x 100 mm acrylic mirror sheet up to 3 mm thick slides in from the side into 3.6 mm channels, and diamond cut-outs let steam and water drain. It measures 104 x 143 x 23 mm and prints on its side, so the hanging load runs along the layers rather than across them.
Under-Desk Game Controller Hanger
A C-shaped hanger that screws to the underside of a desk. A 30 mm-wide, 55 mm-deep tongue fits between the grips of an Xbox- or PlayStation-style controller, and a 12 mm lip keeps the controller from sliding off. It mounts with two #8 (4.2 mm) pan-head wood screws through 4.5 mm holes. A 7 x 30 mm slot in the drop wall lets the charging cable run back under the desk, and the part prints on its side so the load runs along the layers.
Brake Caliper Hanger S-Hook
A flat-printed S-hook that hangs a loose brake caliper from the coil spring, strut body or wheel-well lip so the caliper never dangles on its rubber hose during a pad or rotor job. Both hooks have a 24 mm throat with a 17 mm mouth (takes spring wire up to 17 mm), the body is 136 x 40 x 12 mm with an 8 mm thick hook wall, and a 5.5 mm hole through the spine takes an M5 bolt or a bungee to link two hangers.
Flagged: hydraulic brake system. Not for safety-critical use without independent engineering review.