Print-ready 3D models

Under-Sink P-Trap Riser Shelf

A 140 x 95 mm riser shelf that slides in around a bathroom sink drain so the dead space beside the P-trap becomes usable storage — the 52 mm wide U-slot (26 mm end radius) clears common 1-1/4 in and 1-1/2 in tubular tailpieces and their slip nuts. Four hollow 18 mm legs give 45 mm of clearance over the cabinet floor, 7 mm drain slots let a drip pass straight through instead of pooling under your bottles, and each foot has a 4.5 mm M4 clearance hole if you want to screw it down.

Thumb Page Holder Ring

A one-handed reading aid: slip your thumb through the 22 mm ring and the two 29 mm wings press both page blocks flat so a paperback stays open by itself. Ramped wing tips slide under the pages without creasing them; 80 mm wide overall.

Mini Miter Box Saw Guide

A 120 mm bench-top miter box with guided 90° and left/right 45° saw slots for cutting trim, dowels, and small stock by hand. The channel takes pieces up to 34 mm wide and about 20 mm thick, and two counterbored holes let you screw or clamp it to a bench.

Wall Mail And Key Rack

A 110 mm wall-mounted entryway rack with a 38 mm deep pocket for letters and bills plus three angled hooks with catch lips for keys. Two keyhole slots let it drop onto drywall screws at 88 mm spacing.

Five-Size Drill Guide Block

A handheld drill guide with five tall bushing towers (3.2, 4.2, 5.2, 6.4 and 8.2 mm) that keep a bit perfectly perpendicular, plus a 90° V-groove underside that self-centers the holes on dowels and round stock. Block is 102 x 36 x 44 mm.

Furniture Leg Riser Block

A hollow, rib-cored riser that lifts a bed, couch, desk or dresser leg 44 mm for extra under-furniture storage. The chamfered 58 mm socket accepts square or round legs, and a poke-out hole in the floor frees a stuck leg — order four for one piece of furniture.

Wrap-Around Hand Sanding Block

A palm-sized sanding block with a flat 88 x 68 mm face and a contoured grip; a quarter sheet of sandpaper wraps the bottom and tucks into the two tapered slots on the end shoulders, which wedge tighter as you sand. Hollow-cored so it stays light and cheap to print.

Three-Tier Spice Step Riser

A three-step cabinet riser that stair-steps spice jars so every label is visible from the front. 80 mm wide x 108 mm deep x 66 mm tall, with a 3 mm lip on each tread so jars can't slide off; hollow open-bottom shell with internal ribs to keep it light.

Step-On Boot Jack

A stand-on jack that pulls muddy boots off without touching them: the heel drops into a tapered 20–55 mm V while your other foot holds down the slotted deck. 135 × 60 × 32 mm, prints flat with no supports.

Right Angle Corner Clamp Jig

An 80 mm L-block that holds two boards at a true 90° while glue sets, with open windows so a spring clamp reaches straight through to the workpiece and a rounded corner relief for squeeze-out. Two 4.5 mm holes let you screw it down to a bench or assembly board.

Outlet Cover Phone Shelf

A shelf that hangs on the center screw of a standard duplex outlet cover to hold a charging phone off the floor. 70 mm wide plate, 58 mm deep ledge with an 8 mm lip and a cord notch through the middle.

Round Stock Center Finder

A 90 mm V-jaw layout plate that drops over the end of any round bar, dowel or pipe from about 9 to 70 mm diameter; scribe through the long centre slot, rotate the stock 90° and scribe again — the crossing point is dead centre. The 8 mm deep V lips self-centre the tool so it can't rock off the end face.

Broom And Mop Wall Gripper

A screw-on wall gripper whose springy C-jaws snap over a 20–26 mm broom, mop, rake or squeegee handle so it hangs off the floor. 60 mm back plate with two counterbored screw holes; 18 mm tall jaws with a 19 mm snap mouth.

Toothpaste Tube Squeezer Key

A winding key that grips the flat tail of a toothpaste or ointment tube in a 3.2 mm slot; twist the finger-hole knobs to roll the tube up and push every last bit out. 96 mm long with a Ø7 mm hang hole in one knob.

Wall Hook