Preview in 3D, we print and ship it — or download the file to print yourself.
Heads up: many models on this page are AI-generated or uploaded untested. They may be misconfigured for the intended application — check the dimensions and tolerances, and verify or edit the model before printing or relying on it.
A clamp-on shelf that straddles the top bezel of a monitor and gives a webcam, action cam or small light a solid 41 mm deep platform with a 6.8 mm obround slot for a 1/4-20 tripod screw (14 mm of fore/aft travel) and a 3 mm anti-slide lip. The 18 mm wide throat swallows panels from about 5 mm to 18 mm thick and locks with an M4 x 25 screw into an M4 heat-set insert (5.5 mm bore) in the rear jaw, so nothing presses on the screen; two M3 clearance holes in the deck take a light arm or adapter plate. Overall 78 x 34 x 42 mm, printed as a single profile with no overhangs or supports.
A C-clamp that grips a desktop 12–30 mm thick and holds a vertical 2020 extrusion post at the desk edge, so you can mount a lamp, mic boom, webcam or a small shelf without drilling the desk. 99 x 38 x 30 mm body with a 20.4 mm square socket 40 mm deep (two M5 clearance holes for T-nuts lock the post) and two M4 heat-set inserts in the lower jaw for the M4x30 clamp bolts; the flat 38 x 30 mm upper jaw pad bears on the desk surface and the rear face registers flush against the desk edge. Prints flat on the plate, no supports.
A bolt-clamped replacement slider/holder for a 25 mm shower riser bar, for when the molded plastic holder cracks and the maker only sells the whole $60 rail. A 38 mm split ring with 6.3 mm walls grips the bar via two M5x30 bolts with captured nut pockets, and a 10°-tilted tapered cradle (26.4 mm top, 22.8 mm bottom, open through the bottom so it drains) holds the hand shower. Overall 90 x 39 x 32 mm.
A cable-tie-on bottle cage mount for bikes with no braze-on bosses: a 26 x 26 x 90 mm block with a 90-degree V groove that self-centres on round tubes from about 22 to 32 mm, and two M5 cage bolt bores on the standard 64 mm boss spacing with captured 8 mm hex nuts loaded from the side. Two 8 x 2.8 mm tunnels take 4.8 mm standard or 7.6 mm heavy-duty zip ties that wrap the tube and pull the groove down onto it.
A clamp-on comb that grips the back edge of a desk or shelf (tops up to 27 mm thick) and drops five cables down in separate channels instead of one tangled bundle — two 10 mm channels for laptop/power bricks and three 7 mm channels for USB and audio leads, each with a snap-in mouth so cables push in from the side and stay put. 57 mm wide, 42 mm tall, no drilling: an M4 brass heat-set insert (5.5 mm bore) in the lower jaw takes an M4 x 20–25 bolt that jacks up against the underside of the desktop.
A split collar that clamps onto a standard 1/2" NPT shower arm (21.3 mm OD pipe) with one M4 screw into a heat-set insert, carrying two 30 mm upturned J-hooks for a loofah, razor strap or bottle handle — no suction cups, no drilling tile. Collar bore is 21.8 mm, ring wall 3.5 mm, overall 60 x 38 x 18 mm; slide it on with the shower head removed, then pinch the 3 mm gap closed to lock it.
A tapered 1-cup (240 ml) scoop for dog food, birdseed, coffee beans or detergent, with a flat base so it stands on the counter and a 10 mm hole in the angled handle to hang it on a hook. Bowl is 129 mm long with 2.4 mm walls.
A U-bracket that slips over a cabinet door (fits panels up to 19.5 mm thick) and turns the inside face into a grocery-bag trash caddy — the bag handles drop into a 9 mm trough behind an upturned lip so they can't slide off. 50 mm wide with two optional screw holes for a permanent mount.
A hand-held gripper that slides onto the rim of a hot bowl or plate so you can lift it out of the microwave without a towel. The wedge-shaped jaw self-tightens on rims 5.5–8 mm thick, and the 104 mm handle has finger scallops plus a hang hole.
A flat kitchen paddle with four graduated holes that measure dry spaghetti for 1, 2, 3 or 4 servings, plus a ribbed grip and a hanging hole. 141 mm long, 4.5 mm thick, dishwasher-basket friendly.
A slip-on soft jaw cap for a bench vise: the tapered channel wedges onto jaw plates 12.5–16.5 mm thick, and crossed 90° V-grooves cradle round bar either horizontally or standing upright. 80 mm long, 30 mm tall — print two, one for each jaw.
A flat 150 mm kitchen paddle with seven graduated holes (3–12.5 mm) that strip leaves off rosemary, thyme, kale and chard stems in one pull. Ribbed handle with a hang hole keeps it by the cutting board.
A no-screw C-clamp that slides onto a desk edge or shelf and hangs your headphones underneath on a wide 30 mm saddle. The wedged inner jaw self-tightens on tops from 20–30 mm thick, and the 14 mm hook mouth also takes a bag or lanyard.
An 80 mm L-block that holds two boards at a true 90° while glue sets, with open windows so a spring clamp reaches straight through to the workpiece and a rounded corner relief for squeeze-out. Two 4.5 mm holes let you screw it down to a bench or assembly board.
A countertop tray with a flared twin-rib slot that stands a hot pot lid on edge while the sealed 12 mm-deep basin catches every drip; the rib tops double as a rest for your stirring spoon. Footprint 120 × 90 mm, 32 mm tall ribs, fits lid rims up to 14 mm thick.
A 96 mm wide funnel whose 45° cone seat drops into and self-centers on any jar mouth from 46 to 84 mm, so one funnel covers both regular and wide-mouth mason jars. Two side fins give a no-slip grip while you pour rice, beans, or jam; 48 mm tall with 2.2 mm walls.
A flat lever wrench whose toothed V-jaw bites any lid from about 21 to 72 mm across, so a stuck jar, bottle or pill cap pops with wrist leverage instead of hand strength. 126 mm long, 9 mm thick, with a hang hole in the handle.
A two-compartment caddy that sits beside the faucet to hold a sponge and scrub brush separately, with slotted drain holes in the bottom so water runs out instead of pooling. Fits a standard sponge; overall footprint 100 x 70 x 45 mm.
Print in place bag sealing clips
Fits a 12oz can. Grooved handle for grip.