Preview in 3D, we print and ship it — or download the file to print yourself.
Heads up: many models on this page are AI-generated or uploaded untested. They may be misconfigured for the intended application — check the dimensions and tolerances, and verify or edit the model before printing or relying on it.*
A quarter-round corner shelf for a tiled shower with 100 mm wall legs, a 10 mm retaining lip and radial drain slots so nothing sits in standing water. It screws to the tile through four 4.5 mm holes (#8 / M4 anchors) in 22 mm tall flanges backed by 39° gussets, and two 4 mm slots in the front lip hang a razor by its head.
An oversized 78 mm split escutcheon that clamps onto a 1/2 in NPS shower arm (21.3 mm OD) to hide the chipped drywall or tile hole left after an arm swap — the stock 50 mm flange never covers it, and you can't buy a split one without a whole arm kit. It prints as one piece: a 1.2 mm living-hinge ligament at the rim lets the two halves swing open around the arm in place, then one M3x20 screw through the 3.4 mm lug into the 2.6 mm self-tap pilot pulls the 21.8 mm bore tight. 78 mm dia x 16 mm tall, 2.6 mm brim, print in PETG.
Replacement side-wall channel clip that carries a 1/4 in (6 mm) glass shelf in an old steel or wood medicine cabinet, for when the original stamped clips are long discontinued. The 90 x 22 x 16 mm body has a 6.8 mm wide, 12 mm deep channel with a flared lead-in and a closed back stop, plus two 3.4 mm M3 clearance holes 70 mm apart on tabs clear of the jaws so a screwdriver reaches; the flat 4 mm back also takes VHB tape if you can't drill the cabinet. Symmetric about its centreline, so the same print flipped over serves the opposite wall — print two.
A 120 mm replacement flush lever arm for a toilet tank, for when the brittle OEM arm snaps at the chain hole and the linkage isn't sold separately. Instead of guessing your handle's tab shape, a 14 mm deep forked jaw slides over the handle blade (1.5–3.6 mm thick) and pinches it with an M3×20 screw and a captured M3 nut; five 4 mm chain holes on a 12 mm pitch set the flapper chain length. Arm cross-section is 5 × 12 mm so the bending load runs along the print's strong axis.
A bolt-clamped replacement slider/holder for a 25 mm shower riser bar, for when the molded plastic holder cracks and the maker only sells the whole $60 rail. A 38 mm split ring with 6.3 mm walls grips the bar via two M5x30 bolts with captured nut pockets, and a 10°-tilted tapered cradle (26.4 mm top, 22.8 mm bottom, open through the bottom so it drains) holds the hand shower. Overall 90 x 39 x 32 mm.
A clamp-on double hook that saddles the top edge of a frameless glass shower door — towel hook on the outside, loofah/razor hook on the inside, no drilling, adhesive or suction cup. The 13.6 mm slot with a raised grip pad takes 6–13 mm (1/4"–1/2") tempered glass, and an M4 heat-set insert (5.5 mm bore) plus an M4x16 screw locks it down; 76 x 43 x 26 mm.
A split collar that clamps onto a standard 1/2" NPT shower arm (21.3 mm OD pipe) with one M4 screw into a heat-set insert, carrying two 30 mm upturned J-hooks for a loofah, razor strap or bottle handle — no suction cups, no drilling tile. Collar bore is 21.8 mm, ring wall 3.5 mm, overall 60 x 38 x 18 mm; slide it on with the shower head removed, then pinch the 3 mm gap closed to lock it.