Heads up: many models on this page are AI-generated or uploaded untested. They may be misconfigured for the intended application — check the dimensions and tolerances, and verify or edit the model before printing or relying on it.*
Split Loom 45° Branch Y Trough
A screw-down Y fitting for split-loom harnesses. A 26 mm main channel takes the trunk run, and a 20 mm branch at 45° takes the wires that split off, so you don't have to tape two looms together at the junction. Under-floor zip-tie grooves let a tie wrap each loom end even after the part is screwed flat, and three 4.5 mm holes take #8 screws. It's 112 mm long and 22 mm tall.
Flagged: automotive electrical. Not for safety-critical use without independent engineering review.
Shelly And Sonoff Mini Ceiling Canopy Cradle
A 100 x 56 mm cradle that holds a Shelly 1/1PM/Plus or Sonoff Mini relay module (36–44 mm wide, up to 46 mm long) inside a light-fixture canopy or above a shallow ceiling box, so the relay is not left loose in the cavity. Two cantilever spring fins grip the module, four floor slots plus 5 mm underside channels take zip ties over the module and the Wago 221 tails, and two 4.5 x 14 mm slots take #8 screws at 66–94 mm centres to suit the 2-3/4 in and 3-1/2 in box ear spacings.
Flagged: automotive electrical. Not for safety-critical use without independent engineering review.
Wago 221 Three-Bay Zip-Tie Carrier Plate
Screw-down carrier that stops loose Wago 221 lever connectors rattling around in LED-strip, van and RV low-voltage wiring. Three 32 mm wide bays each take any 2-, 3- or 5-way lever nut up to 32 mm wide; a 6 x 3 mm transverse groove runs under each bay so a standard 4.8 mm zip tie passes beneath the connector and cinches it down, and a second groove in the 13 mm cable strip beyond the bays ties the outgoing wires down for strain relief. Four 4.5 mm holes on a 117 x 22 mm pattern take M4 or #8 screws; plate is 126 x 47 x 8 mm.
Pi 4 Zip-Tie Pipe Saddle Mount
A Raspberry Pi 4 / 3B+ carrier that zip-ties onto any round pipe from 1/2 in EMT (17.9 mm) up to 1 in PVC (33.4 mm). It's for greenhouse, garage-rail or mast sensor nodes where you'd rather not drill. A 90° V-saddle runs the full 90 mm length and is cored into open cells. The M2.5 nuts for the 58 x 49 mm bolt pattern drop into those cells from below, and four tie slots run under the 6 mm standoffs.
Zip-Tie Clamshell Cable Boot Splint
This tapered two-half splint replaces the cracked molded boot behind an RJ45 patch cable or USB plug. It clamps onto cables from 4.5 to 6.5 mm OD: the bore is 6.6 mm with five crush ribs that narrow it to 4.8 mm, and two 4.2 mm zip-tie grooves hold the halves closed. It is 45 mm long and tapers from 18 to 10 mm OD. Both halves print flat as one piece joined by snap-off sprues, so the plug never has to pass through it and a working cable doesn't get binned.
Zip-Tie Twist Tensioning Key
A T-handle key for tightening zip ties on wiring harnesses. It has a 10 mm shaft with a 2.2 mm cross slot that takes any tie up to 1.5 mm thick, whatever the width. Feed the tail into the slot, rest the tip against the tie head, then twist: the tail winds up and pulls the loop tight so you don't have to grip it with pliers. The 80 x 24 mm paddle gives you leverage, the key is 50 mm tall and there's a lanyard hole for hanging it on the bench.
Flagged: lifting or tensioned load. Not for safety-critical use without independent engineering review.
Snap-Slot Wire Harness Lacing Comb
A 110 x 50 x 10 mm lacing comb for building neat wiring looms. Wires press sideways through V lead-ins and snap into seats, so you never have to thread them from the end: 12 seats on the top edge are 3.2 mm with a 2.2 mm neck at 8 mm pitch (about 18–22 AWG hookup wire), and 8 seats on the bottom edge are 4.6 mm with a 3.2 mm neck at 11 mm pitch (about 14–16 AWG). There is a 60 x 12 mm finger window in the middle, and two M4 clearance holes let you screw it to a harness board or slide it along the bundle while you zip-tie or lace the wires at even spacing.
Flagged: automotive electrical. Not for safety-critical use without independent engineering review.
Split Loom V-Saddle Screw Mount
A one-size screw-down saddle for routing split-loom wire harnesses. Its 90° V-cradle is 20 mm wide and 10 mm deep and centres any loom from 6 to 25 mm OD. Two 5.5 x 2.4 mm tunnels under the cradle take zip ties to strap the loom down, so you don't need a multi-pack of P-clips to get the one size you want. The footprint is 60 x 40 x 16.5 mm. The two 4.5 mm holes on 44 mm centres take #8 wood screws (4.2 mm shank) or M4 bolts, for car, boat, garage or control-panel wiring.
Flagged: lifting or tensioned load. Not for safety-critical use without independent engineering review.
Relay And Fuse Zip-Tie Mount Base
A 106 x 52 x 6 mm mounting base (142 mm overall with the screw feet) that gives automotive relay sockets and inline fuse holders something to bolt to instead of dangling off the loom. Two 33 mm bays between 3 mm divider ribs take 4- and 5-pin relay sockets, a 45 degree V-saddle bay cradles round inline fuse holders from roughly 8 to 16 mm, each bay has a pair of 8 x 3.2 mm slots plus a recessed underside channel so a 4.8 mm zip tie loops over the part without lifting the base off the panel, and the two ears carry 4.5 mm M4 clearance holes for firewall or bulkhead screws.
Flagged: automotive electrical. Not for safety-critical use without independent engineering review.