Preview in 3D, we print and ship it — or download the file to print yourself.
Heads up: many models on this page are AI-generated or uploaded untested. They may be misconfigured for the intended application — check the dimensions and tolerances, and verify or edit the model before printing or relying on it.
A split-band clamp that grips a standard round door knob (50–56 mm, eleven internal 1.25 mm grip ribs) and adds a 95 mm lever arm so the door opens with a forearm, elbow or closed fist instead of a twisting grip. One M4 bolt through the 4.5 mm clearance ears pulls the 4 mm split shut onto a captured M4 nut; band is 22 mm tall, arm 14 mm thick, overall 139 x 63 mm, and it prints flat with the lever load in the XY plane.
Replacement wall-end bracket for a broken towel bar, with a stepped socket that takes both 1 in (25.4 mm) and 3/4 in (19 mm) tube — a 1 in bar bottoms on the step after 18 mm, a 3/4 in bar slides 28 mm deep — and an M4 set screw that locks it so you don't have to replace the whole rail set. Back plate is 42 x 68 x 6 mm with two counterbored 4.5 mm holes 52 mm apart for #8/M4 anchors, bar centre stands 38 mm off the wall, overall 55 mm tall.
A split clamp for a 31.8 mm handlebar that carries a second 22.2 mm accessory bar stub 55 mm out to the side, so lights, a GPS, a bell and a phone mount stop fighting for stem space. Closed by two M5 bolts with captured nuts, 99 x 44 x 55 mm, gusseted web under the stub.
A clamp-on shelf that straddles the top bezel of a monitor and gives a webcam, action cam or small light a solid 41 mm deep platform with a 6.8 mm obround slot for a 1/4-20 tripod screw (14 mm of fore/aft travel) and a 3 mm anti-slide lip. The 18 mm wide throat swallows panels from about 5 mm to 18 mm thick and locks with an M4 x 25 screw into an M4 heat-set insert (5.5 mm bore) in the rear jaw, so nothing presses on the screen; two M3 clearance holes in the deck take a light arm or adapter plate. Overall 78 x 34 x 42 mm, printed as a single profile with no overhangs or supports.
A 120 mm replacement flush lever arm for a toilet tank, for when the brittle OEM arm snaps at the chain hole and the linkage isn't sold separately. Instead of guessing your handle's tab shape, a 14 mm deep forked jaw slides over the handle blade (1.5–3.6 mm thick) and pinches it with an M3×20 screw and a captured M3 nut; five 4 mm chain holes on a 12 mm pitch set the flapper chain length. Arm cross-section is 5 × 12 mm so the bending load runs along the print's strong axis.
A C-clamp that grips a desktop 12–30 mm thick and holds a vertical 2020 extrusion post at the desk edge, so you can mount a lamp, mic boom, webcam or a small shelf without drilling the desk. 99 x 38 x 30 mm body with a 20.4 mm square socket 40 mm deep (two M5 clearance holes for T-nuts lock the post) and two M4 heat-set inserts in the lower jaw for the M4x30 clamp bolts; the flat 38 x 30 mm upper jaw pad bears on the desk surface and the rear face registers flush against the desk edge. Prints flat on the plate, no supports.
A bolt-clamped replacement slider/holder for a 25 mm shower riser bar, for when the molded plastic holder cracks and the maker only sells the whole $60 rail. A 38 mm split ring with 6.3 mm walls grips the bar via two M5x30 bolts with captured nut pockets, and a 10°-tilted tapered cradle (26.4 mm top, 22.8 mm bottom, open through the bottom so it drains) holds the hand shower. Overall 90 x 39 x 32 mm.
A clamp-on double hook that saddles the top edge of a frameless glass shower door — towel hook on the outside, loofah/razor hook on the inside, no drilling, adhesive or suction cup. The 13.6 mm slot with a raised grip pad takes 6–13 mm (1/4"–1/2") tempered glass, and an M4 heat-set insert (5.5 mm bore) plus an M4x16 screw locks it down; 76 x 43 x 26 mm.
A cable-tie-on bottle cage mount for bikes with no braze-on bosses: a 26 x 26 x 90 mm block with a 90-degree V groove that self-centres on round tubes from about 22 to 32 mm, and two M5 cage bolt bores on the standard 64 mm boss spacing with captured 8 mm hex nuts loaded from the side. Two 8 x 2.8 mm tunnels take 4.8 mm standard or 7.6 mm heavy-duty zip ties that wrap the tube and pull the groove down onto it.
A stackable closet-flange riser for when new tile or vinyl leaves the toilet flange below the finished floor and the wax ring won't seal. 164 mm OD ring with a 110 mm bore that clears a 4" DWV throat, obround bolt slots on the 139.7 mm (5.5") closet-bolt standard, four 4.5 mm screw holes for #8 anchors, and a 1.5 mm tongue/2.0 mm groove so rings interlock and stack in 6.4 mm (1/4") steps. Print in PETG or ABS at high infill and stack as many as the gap needs.
A clamp-on comb that grips the back edge of a desk or shelf (tops up to 27 mm thick) and drops five cables down in separate channels instead of one tangled bundle — two 10 mm channels for laptop/power bricks and three 7 mm channels for USB and audio leads, each with a snap-in mouth so cables push in from the side and stay put. 57 mm wide, 42 mm tall, no drilling: an M4 brass heat-set insert (5.5 mm bore) in the lower jaw takes an M4 x 20–25 bolt that jacks up against the underside of the desktop.
A split collar that clamps onto a standard 1/2" NPT shower arm (21.3 mm OD pipe) with one M4 screw into a heat-set insert, carrying two 30 mm upturned J-hooks for a loofah, razor strap or bottle handle — no suction cups, no drilling tile. Collar bore is 21.8 mm, ring wall 3.5 mm, overall 60 x 38 x 18 mm; slide it on with the shower head removed, then pinch the 3 mm gap closed to lock it.
A 140 x 95 mm riser shelf that slides in around a bathroom sink drain so the dead space beside the P-trap becomes usable storage — the 52 mm wide U-slot (26 mm end radius) clears common 1-1/4 in and 1-1/2 in tubular tailpieces and their slip nuts. Four hollow 18 mm legs give 45 mm of clearance over the cabinet floor, 7 mm drain slots let a drip pass straight through instead of pooling under your bottles, and each foot has a 4.5 mm M4 clearance hole if you want to screw it down.
A handheld drill guide with five tall bushing towers (3.2, 4.2, 5.2, 6.4 and 8.2 mm) that keep a bit perfectly perpendicular, plus a 90° V-groove underside that self-centers the holes on dowels and round stock. Block is 102 x 36 x 44 mm.
A screw-mounted holster that holds a hair dryer by its barrel in a 64 mm ring so the handle and cord hang clear of the counter. Plate is 62 x 62 mm with two 4.6 mm screw holes on 40 mm centers; the ring stands off the wall 36 mm.
A countertop vanity dispenser: a 61 mm tube that stacks standard cotton rounds with a full-height front slot so you can see the level and pull one out with a thumb, plus an attached 28 mm cup for cotton swabs. Footprint 98 x 66 mm, 82 mm tall.
A no-screw C-clamp that slides onto a desk edge or shelf and hangs your headphones underneath on a wide 30 mm saddle. The wedged inner jaw self-tightens on tops from 20–30 mm thick, and the 14 mm hook mouth also takes a bag or lanyard.
An 80 mm L-block that holds two boards at a true 90° while glue sets, with open windows so a spring clamp reaches straight through to the workpiece and a rounded corner relief for squeeze-out. Two 4.5 mm holes let you screw it down to a bench or assembly board.
A 100 mm wide wall rack that hangs four toothbrushes head-up in open keyhole slots so they drain and air-dry instead of sitting in a wet cup. Slots take handles from the top edge, and four screw holes mount it to drywall or tile.
A 100 x 72 mm bar-soap dish with a 3 mm sloped floor, five lengthwise ribs that keep the bar up out of the water, and a spout notch with a flat drip tongue that sends runoff into the sink instead of onto the counter.
A winding key that grips the flat tail of a toothpaste or ointment tube in a 3.2 mm slot; twist the finger-hole knobs to roll the tube up and push every last bit out. 96 mm long with a Ø7 mm hang hole in one knob.