Preview in 3D, we print and ship it — or download the file to print yourself.
Heads up: many models on this page are AI-generated or uploaded untested. They may be misconfigured for the intended application — check the dimensions and tolerances, and verify or edit the model before printing or relying on it.
Replacement bottom guide for a bypass/sliding shower door: a 46 x 22 x 15 mm block that screws to the track with two countersunk M3 (#6) screws and carries the door's bottom glass edge in a 7.2 mm channel sized for 1/4 in (6.35 mm) glass. A V-shaped lead-in opens the channel to 12.7 mm at the rim so 5/16 in and 3/8 in glass still ride about 5 mm deep, and flared ends in plan view guide a drifting door back in; the counterbored screw holes also drain the channel.
Replacement wall-end bracket for a broken towel bar, with a stepped socket that takes both 1 in (25.4 mm) and 3/4 in (19 mm) tube — a 1 in bar bottoms on the step after 18 mm, a 3/4 in bar slides 28 mm deep — and an M4 set screw that locks it so you don't have to replace the whole rail set. Back plate is 42 x 68 x 6 mm with two counterbored 4.5 mm holes 52 mm apart for #8/M4 anchors, bar centre stands 38 mm off the wall, overall 55 mm tall.
A split clamp for a 31.8 mm handlebar that carries a second 22.2 mm accessory bar stub 55 mm out to the side, so lights, a GPS, a bell and a phone mount stop fighting for stem space. Closed by two M5 bolts with captured nuts, 99 x 44 x 55 mm, gusseted web under the stub.
A print-in-place four-bar over-center toggle clamp (125 x 46 x 26 mm) that pushes a 24 mm wide pad sideways to lock a workpiece against a fence — handle, coupler, arm and base all print as one piece on printed pivot pins with 0.5 mm clearances. The base bolts down with two M5 clearance holes plus two 20 mm M5 slots so the clamp can be slid to the work on a T-track, 2020 rail or drilled bench top.
A 120 mm replacement flush lever arm for a toilet tank, for when the brittle OEM arm snaps at the chain hole and the linkage isn't sold separately. Instead of guessing your handle's tab shape, a 14 mm deep forked jaw slides over the handle blade (1.5–3.6 mm thick) and pinches it with an M3×20 screw and a captured M3 nut; five 4 mm chain holes on a 12 mm pitch set the flapper chain length. Arm cross-section is 5 × 12 mm so the bending load runs along the print's strong axis.
A bolt-clamped replacement slider/holder for a 25 mm shower riser bar, for when the molded plastic holder cracks and the maker only sells the whole $60 rail. A 38 mm split ring with 6.3 mm walls grips the bar via two M5x30 bolts with captured nut pockets, and a 10°-tilted tapered cradle (26.4 mm top, 22.8 mm bottom, open through the bottom so it drains) holds the hand shower. Overall 90 x 39 x 32 mm.
A clamp-on double hook that saddles the top edge of a frameless glass shower door — towel hook on the outside, loofah/razor hook on the inside, no drilling, adhesive or suction cup. The 13.6 mm slot with a raised grip pad takes 6–13 mm (1/4"–1/2") tempered glass, and an M4 heat-set insert (5.5 mm bore) plus an M4x16 screw locks it down; 76 x 43 x 26 mm.
A cable-tie-on bottle cage mount for bikes with no braze-on bosses: a 26 x 26 x 90 mm block with a 90-degree V groove that self-centres on round tubes from about 22 to 32 mm, and two M5 cage bolt bores on the standard 64 mm boss spacing with captured 8 mm hex nuts loaded from the side. Two 8 x 2.8 mm tunnels take 4.8 mm standard or 7.6 mm heavy-duty zip ties that wrap the tube and pull the groove down onto it.
A three-piece print-in-place cam cleat that jams 4–8 mm rope or paracord one-way for tarps, roof racks, awnings and van-life tie-downs — pull to tension, lift the line out to release. Base is 76 x 54 x 16 mm with four 5.5 mm M5 clearance holes on a 60 x 42 mm rectangle; the two toothed cams ride on 6 mm printed pins with retaining heads and are closed by 1.2 mm curved flexure springs, with 4.5 mm guide ribs fairleading the line in.
A stackable closet-flange riser for when new tile or vinyl leaves the toilet flange below the finished floor and the wax ring won't seal. 164 mm OD ring with a 110 mm bore that clears a 4" DWV throat, obround bolt slots on the 139.7 mm (5.5") closet-bolt standard, four 4.5 mm screw holes for #8 anchors, and a 1.5 mm tongue/2.0 mm groove so rings interlock and stack in 6.4 mm (1/4") steps. Print in PETG or ABS at high infill and stack as many as the gap needs.
A split collar that clamps onto a standard 1/2" NPT shower arm (21.3 mm OD pipe) with one M4 screw into a heat-set insert, carrying two 30 mm upturned J-hooks for a loofah, razor strap or bottle handle — no suction cups, no drilling tile. Collar bore is 21.8 mm, ring wall 3.5 mm, overall 60 x 38 x 18 mm; slide it on with the shower head removed, then pinch the 3 mm gap closed to lock it.
A print-in-place hinged tilt bracket for small 10–100 W solar panels, 140 x 60 mm with a 5 mm base plate and a 60 mm-tall detent post. The base bolts to a roof rail, van rack or shed wall with four M5 lag screws (5.5 mm clearance holes) and the panel wing takes four M5 frame bolts; a single M5 x 60 bolt through the post and quadrant fin locks the tilt at 15°, 30°, 45° or 60°, with strap slots on both plates for frameless panels.
A 140 x 95 mm riser shelf that slides in around a bathroom sink drain so the dead space beside the P-trap becomes usable storage — the 52 mm wide U-slot (26 mm end radius) clears common 1-1/4 in and 1-1/2 in tubular tailpieces and their slip nuts. Four hollow 18 mm legs give 45 mm of clearance over the cabinet floor, 7 mm drain slots let a drip pass straight through instead of pooling under your bottles, and each foot has a 4.5 mm M4 clearance hole if you want to screw it down.
A tapered split collar that drops into an oversized patio-table umbrella hole and wedges the pole tight so it stops rattling and leaning. Suits ~38 mm poles in 44–52 mm table holes; 68 mm flange rests on the tabletop.
A screw-mounted holster that holds a hair dryer by its barrel in a 64 mm ring so the handle and cord hang clear of the counter. Plate is 62 x 62 mm with two 4.6 mm screw holes on 40 mm centers; the ring stands off the wall 36 mm.
A countertop vanity dispenser: a 61 mm tube that stacks standard cotton rounds with a full-height front slot so you can see the level and pull one out with a thumb, plus an attached 28 mm cup for cotton swabs. Footprint 98 x 66 mm, 82 mm tall.
A 100 mm wide wall rack that hangs four toothbrushes head-up in open keyhole slots so they drain and air-dry instead of sitting in a wet cup. Slots take handles from the top edge, and four screw holes mount it to drywall or tile.
A 100 x 72 mm bar-soap dish with a 3 mm sloped floor, five lengthwise ribs that keep the bar up out of the water, and a spout notch with a flat drip tongue that sends runoff into the sink instead of onto the counter.
A winding key that grips the flat tail of a toothpaste or ointment tube in a 3.2 mm slot; twist the finger-hole knobs to roll the tube up and push every last bit out. 96 mm long with a Ø7 mm hang hole in one knob.