Preview in 3D, we print and ship it — or download the file to print yourself.
Heads up: many models on this page are AI-generated or uploaded untested. They may be misconfigured for the intended application — check the dimensions and tolerances, and verify or edit the model before printing or relying on it.
A bench-top fume extractor housing for any 40 x 40 x 10 mm fan — the fan bolts to the 60°-tilted face on its standard 32 mm M3 pattern (3.4 mm clearance holes with counterbores so the heads sit flush), and a 42 mm square of activated-carbon filter sheet press-fits into the 41.5 x 41.5 x 4 mm pocket in front of a ribbed finger-guard throat. Footprint 52 x 64 mm, 50 mm tall, with two M4 holes in the weighted base for bolting it to the bench and an open rear duct so exhaust clears the work.
A four-link cable drag chain with an integrated M3 mounting foot, printed fully assembled — no pins, no clips, no post-assembly. Each 32 mm link carries an 11 mm wide x 13 mm tall cable channel and an arc-slot bend limiter that stops the chain dead straight and allows 35 deg of bend, so the top run won't sag. Overall 170 x 29 x 16 mm; the foot takes two M3 screws on a 19 mm spacing.
A 104 x 46 x 16 mm bench dock that stands up 6 microSD cards (11 x 15 x 1 mm), 3 full-size SD cards (24 x 32 x 2.1 mm) and 4 USB-A flash drives parked plug-down in 12.8 x 5.4 mm bays, so the loose media around a Pi/camera bench stops disappearing into the parts bin. Cards protrude 7–20 mm for a one-finger pinch, a scalloped thumb groove backs the microSD row, and two M3 clearance holes on a 96 mm centre let you screw it into a drawer bottom or shelf; underside relief pockets keep it to roughly 57 cm³.
A 62 mm square, 19 mm tall adapter that lets a NEMA 17 stepper bolt into a machine face drilled for NEMA 23 — the base carries the 47.14 mm M5 pattern, the raised Ø52 tower carries the 31 mm M3 pattern with a 22.4 mm pilot register for the motor's centring boss. The hollow Ø30 core clears a shaft coupler, a 14 mm side window gives Allen-key access to the coupler set screw, and counterbores in the base bottom fully recess the four M3x20 motor screws so the adapter still seats flat.
A six-lane stadium-step rack that sorts cut heat-shrink tubing by diameter — troughs 8/10/12/14/17/20 mm wide take the common 3:1 sizes from 2.4 mm up to 12.7 mm, each 74 mm long with a finger scallop so you can pinch a piece out without emptying the lane. 116 x 99 x 39 mm overall, open underneath to stay light, with two M4 clearance ears (4.5 mm) to screw it to a shelf or bench back.
A curved clip that wedges onto the rim of a 1-gallon paint can, giving you a clean edge to wipe your brush on and a slot to park it over the paint instead of on the rim. Spans a 50° arc of the can, about 74 mm wide.
A ground stake with a tapered funnel socket that grips 12 oz cans, bottles and tapered party cups so drinks stay upright in sand, grass or dirt. 148 mm tall with four grip ribs at the rim for pushing it in by hand.
A 147 mm staircase block that stands a 13-piece metric drill index upright, with bores from 1.5 mm to 7.5 mm rising left to right so the size order is obvious at a glance. Each step is taller than the last, so bit tips sit deep and shanks stay easy to grab.
A 60 mm one-piece carabiner whose gate is a built-in flexing spring arm — press it inward to hook on, and a capture nose stops it opening under load. Prints flat with no supports, no assembly, and no metal spring; sized for keys, water bottles, and bag straps.
A screw-on wall gripper whose springy C-jaws snap over a 20–26 mm broom, mop, rake or squeegee handle so it hangs off the floor. 60 mm back plate with two counterbored screw holes; 18 mm tall jaws with a 19 mm snap mouth.