Preview in 3D, we print and ship it — or download the file to print yourself.
Heads up: many models on this page are AI-generated or uploaded untested. They may be misconfigured for the intended application — check the dimensions and tolerances, and verify or edit the model before printing or relying on it.
A wired-mouse cable bungee whose compliance comes from a printed bow spring: a 2.4 mm x 12 mm leaf arch bends in the XY plane (along the layer lines, not across them) so the 50 mm guide post springs fore-and-aft and keeps drag off the mouse. The 62 x 30 x 5 mm foot sticks down with a VHB square (the spring rides 1 mm clear of the desk) or bolts down through two 4.5 mm M4 clearance holes; the cable snaps into a 6.4 mm trough 43 mm up through a 4.4 mm pinch and still slides freely. Overall 62 x 73 x 50 mm, about 22 cm3 of plastic.
A 114 x 114 mm plate that bolts to a monitor's VESA 75 x 75 or 100 x 100 M4 pattern (sandwiched under the arm/stand screws) and carries a 92 x 50 mm tray with 23 mm side walls and a 7 mm front rail behind the screen. A 62 mm centre window clears the arm head, twin 5 x 16 mm strap slots and a 10 mm cable pass-through hold a USB hub, dongle receiver, SSD or mini PC off the desk.
An open-bottom gabled shelter that covers an outdoor extension-cord plug/connector joint so rain and sprinkler spray drip off instead of sitting on the contacts — 140 mm long with a 52.8 x 46 mm internal cavity, big enough for a 5-15 plug mated into a cord end. Both end walls carry an 11 mm cord slot (fits 16/3 and 12/3 SJTW cord) flanked by 4.5 mm M4 zip-tie holes, and four 5.5 mm M5 holes in the bottom flange take ground stakes, landscape staples or screws into a deck rail. The 45° roof and vertical walls print with no supports and no bridging over the cavity.
A C-clamp that grips a desktop 12–30 mm thick and holds a vertical 2020 extrusion post at the desk edge, so you can mount a lamp, mic boom, webcam or a small shelf without drilling the desk. 99 x 38 x 30 mm body with a 20.4 mm square socket 40 mm deep (two M5 clearance holes for T-nuts lock the post) and two M4 heat-set inserts in the lower jaw for the M4x30 clamp bolts; the flat 38 x 30 mm upper jaw pad bears on the desk surface and the rear face registers flush against the desk edge. Prints flat on the plate, no supports.
A four-link cable drag chain with an integrated M3 mounting foot, printed fully assembled — no pins, no clips, no post-assembly. Each 32 mm link carries an 11 mm wide x 13 mm tall cable channel and an arc-slot bend limiter that stops the chain dead straight and allows 35 deg of bend, so the top run won't sag. Overall 170 x 29 x 16 mm; the foot takes two M3 screws on a 19 mm spacing.
An 86 x 44 x 16 mm under-dash bracket that gets a telematics dongle, OBDLink adapter or dashcam hardwire pigtail off the driver's shin and stops it levering the OBD-II socket out of its retainer. A 25 mm velcro strap passes through two slots and under the 4 mm raised deck so any size dongle clamps down, a snap clip at the exit end grips 5-8 mm cable as strain relief, and the solid pad mounts with two M4 screws (4.5 mm clearance) or two zip ties looped around a round dash brace.
A clamp-on comb that grips the back edge of a desk or shelf (tops up to 27 mm thick) and drops five cables down in separate channels instead of one tangled bundle — two 10 mm channels for laptop/power bricks and three 7 mm channels for USB and audio leads, each with a snap-in mouth so cables push in from the side and stay put. 57 mm wide, 42 mm tall, no drilling: an M4 brass heat-set insert (5.5 mm bore) in the lower jaw takes an M4 x 20–25 bolt that jacks up against the underside of the desktop.
A curved clip that wedges onto the rim of a 1-gallon paint can, giving you a clean edge to wipe your brush on and a slot to park it over the paint instead of on the rim. Spans a 50° arc of the can, about 74 mm wide.
A weighted-footprint cradle that holds a closed laptop, tablet or notebook upright on the desk, with a 22 mm slot, chamfered lead-in edges and a cable pass-through slot in the floor. 90 × 70 × 50 mm.