Preview in 3D, we print and ship it — or download the file to print yourself.
Heads up: many models on this page are AI-generated or uploaded untested. They may be misconfigured for the intended application — check the dimensions and tolerances, and verify or edit the model before printing or relying on it.
A cradle chassis for building a 3S (or 3P) 18650 pack: three 18.9 mm teardrop bores on 21.5 mm centres hold the cells in two 8 mm end collars plus a mid saddle, leaving both terminals flush with the outer faces at exactly 65 mm so nickel strip can be welded straight across. 82 x 68 x 34 mm, with raised + / − polarity ribs above each bore alternating for series wiring, four 3.4 mm M3 clearance holes to bolt the pack into a project, and four 12 x 5 mm zip-tie slots through the 3.5 mm base.
A weather cap for a nominal 4x4 fence or deck post (88.9 mm actual) with a 91 mm square socket, 20 mm engagement and two M4 clearance holes so it screws down and won't blow off. Twin horns on opposite faces carry a cafe-string-light cable in an 8 mm wide, 10 mm deep slot; overall 127 x 97 x 50 mm with a hollow 50-degree pyramid roof that sheds water and prints support-free.
A clamp-on double hook that saddles the top edge of a frameless glass shower door — towel hook on the outside, loofah/razor hook on the inside, no drilling, adhesive or suction cup. The 13.6 mm slot with a raised grip pad takes 6–13 mm (1/4"–1/2") tempered glass, and an M4 heat-set insert (5.5 mm bore) plus an M4x16 screw locks it down; 76 x 43 x 26 mm.
A four-bay bench or wall caddy that stands RC LiPo packs upright, each bay 34 x 28 mm (fits packs up to about 33 x 27 mm in cross-section — the usual 2S/3S 1300–2600 mAh class) with a dedicated 10 mm rear channel per bay so the balance lead drops over a 36 mm divider wall and its plug hangs isolated from the neighbouring pack's main leads. Overall 148 x 47 x 52 mm, with a push-up window under each bay and two M4 clearance holes (4.5 mm) through the 4 mm back wall for wall mounting.
A 120 mm slide-on splint sleeve that repairs a snapped 11 mm tent pole section: 11.4 mm teardrop bore (0.4 mm slip fit), 4 mm walls, tapered lead-in mouths at both ends, and two M3 self-tapping set-screw bosses (2.6 mm holes) that pin it to each pole half so it can't migrate off the break. A centre notch in the full-length stiffening rib lines it up on the crack; overall 120 x 19.4 x 22 mm with a flat printed pad on the bottom. Print in PETG or ASA for UV and cold tolerance.
A split collar that clamps onto a standard 1/2" NPT shower arm (21.3 mm OD pipe) with one M4 screw into a heat-set insert, carrying two 30 mm upturned J-hooks for a loofah, razor strap or bottle handle — no suction cups, no drilling tile. Collar bore is 21.8 mm, ring wall 3.5 mm, overall 60 x 38 x 18 mm; slide it on with the shower head removed, then pinch the 3 mm gap closed to lock it.
A 44 mm square block with four through-bores (18.7 mm, on 20.6 mm centres) that holds four 18650 cells upright, parallel and bottom-flush against the bench so nickel strip lands square during spot-welding or pack glue-up. Open-topped grab notches — one per cell, in 4-fold symmetry — let you spin a cell to set polarity, and two 5 mm ears with M3 clearance holes bolt the jig to the bench; overall 68 x 44 x 26 mm.
A U-bracket that slips over a cabinet door (fits panels up to 19.5 mm thick) and turns the inside face into a grocery-bag trash caddy — the bag handles drop into a 9 mm trough behind an upturned lip so they can't slide off. 50 mm wide with two optional screw holes for a permanent mount.
A ground stake with a tapered funnel socket that grips 12 oz cans, bottles and tapered party cups so drinks stay upright in sand, grass or dirt. 148 mm tall with four grip ribs at the rim for pushing it in by hand.
A no-screw C-clamp that slides onto a desk edge or shelf and hangs your headphones underneath on a wide 30 mm saddle. The wedged inner jaw self-tightens on tops from 20–30 mm thick, and the 14 mm hook mouth also takes a bag or lanyard.
A gravity-fed dual-channel dispenser that stacks 6 AA and 8 AAA cells and drops the next one into a front grab window with a retaining lip. Stands 92 mm tall on a shelf or screws to a wall through the two rear ears.