Preview in 3D, we print and ship it — or download the file to print yourself.
Heads up: many models on this page are AI-generated or uploaded untested. They may be misconfigured for the intended application — check the dimensions and tolerances, and verify or edit the model before printing or relying on it.
A weather cap for a nominal 4x4 fence or deck post (88.9 mm actual) with a 91 mm square socket, 20 mm engagement and two M4 clearance holes so it screws down and won't blow off. Twin horns on opposite faces carry a cafe-string-light cable in an 8 mm wide, 10 mm deep slot; overall 127 x 97 x 50 mm with a hollow 50-degree pyramid roof that sheds water and prints support-free.
A clamp-on double hook that saddles the top edge of a frameless glass shower door — towel hook on the outside, loofah/razor hook on the inside, no drilling, adhesive or suction cup. The 13.6 mm slot with a raised grip pad takes 6–13 mm (1/4"–1/2") tempered glass, and an M4 heat-set insert (5.5 mm bore) plus an M4x16 screw locks it down; 76 x 43 x 26 mm.
A stackable closet-flange riser for when new tile or vinyl leaves the toilet flange below the finished floor and the wax ring won't seal. 164 mm OD ring with a 110 mm bore that clears a 4" DWV throat, obround bolt slots on the 139.7 mm (5.5") closet-bolt standard, four 4.5 mm screw holes for #8 anchors, and a 1.5 mm tongue/2.0 mm groove so rings interlock and stack in 6.4 mm (1/4") steps. Print in PETG or ABS at high infill and stack as many as the gap needs.
A 120 mm slide-on splint sleeve that repairs a snapped 11 mm tent pole section: 11.4 mm teardrop bore (0.4 mm slip fit), 4 mm walls, tapered lead-in mouths at both ends, and two M3 self-tapping set-screw bosses (2.6 mm holes) that pin it to each pole half so it can't migrate off the break. A centre notch in the full-length stiffening rib lines it up on the crack; overall 120 x 19.4 x 22 mm with a flat printed pad on the bottom. Print in PETG or ASA for UV and cold tolerance.
A split collar that clamps onto a standard 1/2" NPT shower arm (21.3 mm OD pipe) with one M4 screw into a heat-set insert, carrying two 30 mm upturned J-hooks for a loofah, razor strap or bottle handle — no suction cups, no drilling tile. Collar bore is 21.8 mm, ring wall 3.5 mm, overall 60 x 38 x 18 mm; slide it on with the shower head removed, then pinch the 3 mm gap closed to lock it.
A 140 x 95 mm riser shelf that slides in around a bathroom sink drain so the dead space beside the P-trap becomes usable storage — the 52 mm wide U-slot (26 mm end radius) clears common 1-1/4 in and 1-1/2 in tubular tailpieces and their slip nuts. Four hollow 18 mm legs give 45 mm of clearance over the cabinet floor, 7 mm drain slots let a drip pass straight through instead of pooling under your bottles, and each foot has a 4.5 mm M4 clearance hole if you want to screw it down.
A U-bracket that slips over a cabinet door (fits panels up to 19.5 mm thick) and turns the inside face into a grocery-bag trash caddy — the bag handles drop into a 9 mm trough behind an upturned lip so they can't slide off. 50 mm wide with two optional screw holes for a permanent mount.
A ground stake with a tapered funnel socket that grips 12 oz cans, bottles and tapered party cups so drinks stay upright in sand, grass or dirt. 148 mm tall with four grip ribs at the rim for pushing it in by hand.
A no-screw C-clamp that slides onto a desk edge or shelf and hangs your headphones underneath on a wide 30 mm saddle. The wedged inner jaw self-tightens on tops from 20–30 mm thick, and the 14 mm hook mouth also takes a bag or lanyard.