Preview in 3D, we print and ship it — or download the file to print yourself.
Heads up: many models on this page are AI-generated or uploaded untested. They may be misconfigured for the intended application — check the dimensions and tolerances, and verify or edit the model before printing or relying on it.
A 114 x 114 mm plate that bolts to a monitor's VESA 75 x 75 or 100 x 100 M4 pattern (sandwiched under the arm/stand screws) and carries a 92 x 50 mm tray with 23 mm side walls and a 7 mm front rail behind the screen. A 62 mm centre window clears the arm head, twin 5 x 16 mm strap slots and a 10 mm cable pass-through hold a USB hub, dongle receiver, SSD or mini PC off the desk.
An open-bottom gabled shelter that covers an outdoor extension-cord plug/connector joint so rain and sprinkler spray drip off instead of sitting on the contacts — 140 mm long with a 52.8 x 46 mm internal cavity, big enough for a 5-15 plug mated into a cord end. Both end walls carry an 11 mm cord slot (fits 16/3 and 12/3 SJTW cord) flanked by 4.5 mm M4 zip-tie holes, and four 5.5 mm M5 holes in the bottom flange take ground stakes, landscape staples or screws into a deck rail. The 45° roof and vertical walls print with no supports and no bridging over the cavity.
A C-clamp that grips a desktop 12–30 mm thick and holds a vertical 2020 extrusion post at the desk edge, so you can mount a lamp, mic boom, webcam or a small shelf without drilling the desk. 99 x 38 x 30 mm body with a 20.4 mm square socket 40 mm deep (two M5 clearance holes for T-nuts lock the post) and two M4 heat-set inserts in the lower jaw for the M4x30 clamp bolts; the flat 38 x 30 mm upper jaw pad bears on the desk surface and the rear face registers flush against the desk edge. Prints flat on the plate, no supports.
A four-link cable drag chain with an integrated M3 mounting foot, printed fully assembled — no pins, no clips, no post-assembly. Each 32 mm link carries an 11 mm wide x 13 mm tall cable channel and an arc-slot bend limiter that stops the chain dead straight and allows 35 deg of bend, so the top run won't sag. Overall 170 x 29 x 16 mm; the foot takes two M3 screws on a 19 mm spacing.
An 86 x 44 x 16 mm under-dash bracket that gets a telematics dongle, OBDLink adapter or dashcam hardwire pigtail off the driver's shin and stops it levering the OBD-II socket out of its retainer. A 25 mm velcro strap passes through two slots and under the 4 mm raised deck so any size dongle clamps down, a snap clip at the exit end grips 5-8 mm cable as strain relief, and the solid pad mounts with two M4 screws (4.5 mm clearance) or two zip ties looped around a round dash brace.
A clamp-on comb that grips the back edge of a desk or shelf (tops up to 27 mm thick) and drops five cables down in separate channels instead of one tangled bundle — two 10 mm channels for laptop/power bricks and three 7 mm channels for USB and audio leads, each with a snap-in mouth so cables push in from the side and stay put. 57 mm wide, 42 mm tall, no drilling: an M4 brass heat-set insert (5.5 mm bore) in the lower jaw takes an M4 x 20–25 bolt that jacks up against the underside of the desktop.
A two-horn wall cleat for figure-eight wrapping an extension cord, air hose or rope, with flared post tips that keep the coil from slipping off. 120 mm wide, mounts with two countersunk screws and holds roughly a 50 ft 16-gauge cord.
A weighted-footprint cradle that holds a closed laptop, tablet or notebook upright on the desk, with a 22 mm slot, chamfered lead-in edges and a cable pass-through slot in the floor. 90 × 70 × 50 mm.