Preview in 3D, we print and ship it — or download the file to print yourself.
Heads up: many models on this page are AI-generated or uploaded untested. They may be misconfigured for the intended application — check the dimensions and tolerances, and verify or edit the model before printing or relying on it.
A bench-top fume extractor housing for any 40 x 40 x 10 mm fan — the fan bolts to the 60°-tilted face on its standard 32 mm M3 pattern (3.4 mm clearance holes with counterbores so the heads sit flush), and a 42 mm square of activated-carbon filter sheet press-fits into the 41.5 x 41.5 x 4 mm pocket in front of a ribbed finger-guard throat. Footprint 52 x 64 mm, 50 mm tall, with two M4 holes in the weighted base for bolting it to the bench and an open rear duct so exhaust clears the work.
A standoff bridge that suspends a 40 mm fan directly over a Raspberry Pi 4B / 3B+, with a 32 mm shrouded duct collar aiming the air at the SoC instead of letting it spill sideways. 74 x 64 mm plate on four 18 mm legs that clear the USB/Ethernet stack, 58 x 49 mm M2.5 board pattern with captured nuts at the board end, 32 mm square M3 fan pattern, plus side exhaust vents and a 26 x 4.5 mm slot for GPIO ribbon or camera flex.
A 104 x 46 x 16 mm bench dock that stands up 6 microSD cards (11 x 15 x 1 mm), 3 full-size SD cards (24 x 32 x 2.1 mm) and 4 USB-A flash drives parked plug-down in 12.8 x 5.4 mm bays, so the loose media around a Pi/camera bench stops disappearing into the parts bin. Cards protrude 7–20 mm for a one-finger pinch, a scalloped thumb groove backs the microSD row, and two M3 clearance holes on a 96 mm centre let you screw it into a drawer bottom or shelf; underside relief pockets keep it to roughly 57 cm³.
A six-lane stadium-step rack that sorts cut heat-shrink tubing by diameter — troughs 8/10/12/14/17/20 mm wide take the common 3:1 sizes from 2.4 mm up to 12.7 mm, each 74 mm long with a finger scallop so you can pinch a piece out without emptying the lane. 116 x 99 x 39 mm overall, open underneath to stay light, with two M4 clearance ears (4.5 mm) to screw it to a shelf or bench back.
A 28 mm tall tapered duct that lets a 60 mm fan feed an 80 mm fan opening (or vice versa): 80 x 80 mm flange with M4 clearance holes on the 71.5 mm pattern at the bottom, 60 x 60 mm face with four 3.4 mm self-tapping M4 bosses on the 50 mm pattern on top. The airway necks smoothly from 73 mm to 55 mm with a 2 mm wall, so it replaces a grinder/zip-tie bodge on amp racks, 3D-printer electronics bays and PC cases.
A curved clip that wedges onto the rim of a 1-gallon paint can, giving you a clean edge to wipe your brush on and a slot to park it over the paint instead of on the rim. Spans a 50° arc of the can, about 74 mm wide.
A two-horn wall cleat for figure-eight wrapping an extension cord, air hose or rope, with flared post tips that keep the coil from slipping off. 120 mm wide, mounts with two countersunk screws and holds roughly a 50 ft 16-gauge cord.
A 147 mm staircase block that stands a 13-piece metric drill index upright, with bores from 1.5 mm to 7.5 mm rising left to right so the size order is obvious at a glance. Each step is taller than the last, so bit tips sit deep and shanks stay easy to grab.
A 60 mm one-piece carabiner whose gate is a built-in flexing spring arm — press it inward to hook on, and a capture nose stops it opening under load. Prints flat with no supports, no assembly, and no metal spring; sized for keys, water bottles, and bag straps.
A screw-on wall gripper whose springy C-jaws snap over a 20–26 mm broom, mop, rake or squeegee handle so it hangs off the floor. 60 mm back plate with two counterbored screw holes; 18 mm tall jaws with a 19 mm snap mouth.