Preview in 3D, we print and ship it — or download the file to print yourself.
Heads up: many models on this page are AI-generated or uploaded untested. They may be misconfigured for the intended application — check the dimensions and tolerances, and verify or edit the model before printing or relying on it.
Replacement wall-end bracket for a broken towel bar, with a stepped socket that takes both 1 in (25.4 mm) and 3/4 in (19 mm) tube — a 1 in bar bottoms on the step after 18 mm, a 3/4 in bar slides 28 mm deep — and an M4 set screw that locks it so you don't have to replace the whole rail set. Back plate is 42 x 68 x 6 mm with two counterbored 4.5 mm holes 52 mm apart for #8/M4 anchors, bar centre stands 38 mm off the wall, overall 55 mm tall.
A 120 mm replacement flush lever arm for a toilet tank, for when the brittle OEM arm snaps at the chain hole and the linkage isn't sold separately. Instead of guessing your handle's tab shape, a 14 mm deep forked jaw slides over the handle blade (1.5–3.6 mm thick) and pinches it with an M3×20 screw and a captured M3 nut; five 4 mm chain holes on a 12 mm pitch set the flapper chain length. Arm cross-section is 5 × 12 mm so the bending load runs along the print's strong axis.
A bolt-clamped replacement slider/holder for a 25 mm shower riser bar, for when the molded plastic holder cracks and the maker only sells the whole $60 rail. A 38 mm split ring with 6.3 mm walls grips the bar via two M5x30 bolts with captured nut pockets, and a 10°-tilted tapered cradle (26.4 mm top, 22.8 mm bottom, open through the bottom so it drains) holds the hand shower. Overall 90 x 39 x 32 mm.
A four-link cable drag chain with an integrated M3 mounting foot, printed fully assembled — no pins, no clips, no post-assembly. Each 32 mm link carries an 11 mm wide x 13 mm tall cable channel and an arc-slot bend limiter that stops the chain dead straight and allows 35 deg of bend, so the top run won't sag. Overall 170 x 29 x 16 mm; the foot takes two M3 screws on a 19 mm spacing.
A 120 mm slide-on splint sleeve that repairs a snapped 11 mm tent pole section: 11.4 mm teardrop bore (0.4 mm slip fit), 4 mm walls, tapered lead-in mouths at both ends, and two M3 self-tapping set-screw bosses (2.6 mm holes) that pin it to each pole half so it can't migrate off the break. A centre notch in the full-length stiffening rib lines it up on the crack; overall 120 x 19.4 x 22 mm with a flat printed pad on the bottom. Print in PETG or ASA for UV and cold tolerance.
A 62 mm square, 19 mm tall adapter that lets a NEMA 17 stepper bolt into a machine face drilled for NEMA 23 — the base carries the 47.14 mm M5 pattern, the raised Ø52 tower carries the 31 mm M3 pattern with a 22.4 mm pilot register for the motor's centring boss. The hollow Ø30 core clears a shaft coupler, a 14 mm side window gives Allen-key access to the coupler set screw, and counterbores in the base bottom fully recess the four M3x20 motor screws so the adapter still seats flat.
A 95 x 70 mm catch-all tray with two compartments for keys and coins plus an upright slot that stands a phone (up to 13 mm thick with case) face-up on a raised shelf. A tunnel through the back wall feeds the charging cable up to the phone's port so the cord never leaves the dock.
A two-horn wall cleat for figure-eight wrapping an extension cord, air hose or rope, with flared post tips that keep the coil from slipping off. 120 mm wide, mounts with two countersunk screws and holds roughly a 50 ft 16-gauge cord.