Preview in 3D, we print and ship it — or download the file to print yourself.
Heads up: many models on this page are AI-generated or uploaded untested. They may be misconfigured for the intended application — check the dimensions and tolerances, and verify or edit the model before printing or relying on it.
A one-piece dust-extraction adapter that joins a 2-1/2 in (63.5 mm) shop-vac hose to a 1-1/4 in (31.75 mm) power-tool dust port — a 64.0 mm socket with an internal 45° stop shoulder steps down through a tapered cone to a 31.4→30.6 mm friction spigot with a seating flange. 79 mm tall, 78 mm across the three grip ribs, with a 3.4 mm M4 self-tapping screw hole through one rib so the hose can be locked instead of pulling off mid-cut.
A four-link cable drag chain with an integrated M3 mounting foot, printed fully assembled — no pins, no clips, no post-assembly. Each 32 mm link carries an 11 mm wide x 13 mm tall cable channel and an arc-slot bend limiter that stops the chain dead straight and allows 35 deg of bend, so the top run won't sag. Overall 170 x 29 x 16 mm; the foot takes two M3 screws on a 19 mm spacing.
A 62 mm square, 19 mm tall adapter that lets a NEMA 17 stepper bolt into a machine face drilled for NEMA 23 — the base carries the 47.14 mm M5 pattern, the raised Ø52 tower carries the 31 mm M3 pattern with a 22.4 mm pilot register for the motor's centring boss. The hollow Ø30 core clears a shaft coupler, a 14 mm side window gives Allen-key access to the coupler set screw, and counterbores in the base bottom fully recess the four M3x20 motor screws so the adapter still seats flat.
A 120 mm bench-top miter box with guided 90° and left/right 45° saw slots for cutting trim, dowels, and small stock by hand. The channel takes pieces up to 34 mm wide and about 20 mm thick, and two counterbored holes let you screw or clamp it to a bench.
A weighted-footprint cup that parks a wood glue bottle nozzle-down so the glue is always primed and never crusts over. The tapered Ø27–35 mm bore self-centers most 8–16 oz caps, with a 12 mm drip well below the tip and two side slots for grip and level checking; 80 mm base, 60 mm tall.
A handheld drill guide with five tall bushing towers (3.2, 4.2, 5.2, 6.4 and 8.2 mm) that keep a bit perfectly perpendicular, plus a 90° V-groove underside that self-centers the holes on dowels and round stock. Block is 102 x 36 x 44 mm.
A palm-sized sanding block with a flat 88 x 68 mm face and a contoured grip; a quarter sheet of sandpaper wraps the bottom and tucks into the two tapered slots on the end shoulders, which wedge tighter as you sand. Hollow-cored so it stays light and cheap to print.
An 80 mm L-block that holds two boards at a true 90° while glue sets, with open windows so a spring clamp reaches straight through to the workpiece and a rounded corner relief for squeeze-out. Two 4.5 mm holes let you screw it down to a bench or assembly board.
A 147 mm staircase block that stands a 13-piece metric drill index upright, with bores from 1.5 mm to 7.5 mm rising left to right so the size order is obvious at a glance. Each step is taller than the last, so bit tips sit deep and shanks stay easy to grab.
A 90 mm V-jaw layout plate that drops over the end of any round bar, dowel or pipe from about 9 to 70 mm diameter; scribe through the long centre slot, rotate the stock 90° and scribe again — the crossing point is dead centre. The 8 mm deep V lips self-centre the tool so it can't rock off the end face.
A weighted-footprint cradle that holds a closed laptop, tablet or notebook upright on the desk, with a 22 mm slot, chamfered lead-in edges and a cable pass-through slot in the floor. 90 × 70 × 50 mm.