Preview in 3D, we print and ship it — or download the file to print yourself.
Heads up: many models on this page are AI-generated or uploaded untested. They may be misconfigured for the intended application — check the dimensions and tolerances, and verify or edit the model before printing or relying on it.
A split-band clamp that grips a standard round door knob (50–56 mm, eleven internal 1.25 mm grip ribs) and adds a 95 mm lever arm so the door opens with a forearm, elbow or closed fist instead of a twisting grip. One M4 bolt through the 4.5 mm clearance ears pulls the 4 mm split shut onto a captured M4 nut; band is 22 mm tall, arm 14 mm thick, overall 139 x 63 mm, and it prints flat with the lever load in the XY plane.
A split clamp for a 31.8 mm handlebar that carries a second 22.2 mm accessory bar stub 55 mm out to the side, so lights, a GPS, a bell and a phone mount stop fighting for stem space. Closed by two M5 bolts with captured nuts, 99 x 44 x 55 mm, gusseted web under the stub.
A bench-top fume extractor housing for any 40 x 40 x 10 mm fan — the fan bolts to the 60°-tilted face on its standard 32 mm M3 pattern (3.4 mm clearance holes with counterbores so the heads sit flush), and a 42 mm square of activated-carbon filter sheet press-fits into the 41.5 x 41.5 x 4 mm pocket in front of a ribbed finger-guard throat. Footprint 52 x 64 mm, 50 mm tall, with two M4 holes in the weighted base for bolting it to the bench and an open rear duct so exhaust clears the work.
A clamp-on shelf that straddles the top bezel of a monitor and gives a webcam, action cam or small light a solid 41 mm deep platform with a 6.8 mm obround slot for a 1/4-20 tripod screw (14 mm of fore/aft travel) and a 3 mm anti-slide lip. The 18 mm wide throat swallows panels from about 5 mm to 18 mm thick and locks with an M4 x 25 screw into an M4 heat-set insert (5.5 mm bore) in the rear jaw, so nothing presses on the screen; two M3 clearance holes in the deck take a light arm or adapter plate. Overall 78 x 34 x 42 mm, printed as a single profile with no overhangs or supports.
A C-clamp that grips a desktop 12–30 mm thick and holds a vertical 2020 extrusion post at the desk edge, so you can mount a lamp, mic boom, webcam or a small shelf without drilling the desk. 99 x 38 x 30 mm body with a 20.4 mm square socket 40 mm deep (two M5 clearance holes for T-nuts lock the post) and two M4 heat-set inserts in the lower jaw for the M4x30 clamp bolts; the flat 38 x 30 mm upper jaw pad bears on the desk surface and the rear face registers flush against the desk edge. Prints flat on the plate, no supports.
A bolt-clamped replacement slider/holder for a 25 mm shower riser bar, for when the molded plastic holder cracks and the maker only sells the whole $60 rail. A 38 mm split ring with 6.3 mm walls grips the bar via two M5x30 bolts with captured nut pockets, and a 10°-tilted tapered cradle (26.4 mm top, 22.8 mm bottom, open through the bottom so it drains) holds the hand shower. Overall 90 x 39 x 32 mm.
A cable-tie-on bottle cage mount for bikes with no braze-on bosses: a 26 x 26 x 90 mm block with a 90-degree V groove that self-centres on round tubes from about 22 to 32 mm, and two M5 cage bolt bores on the standard 64 mm boss spacing with captured 8 mm hex nuts loaded from the side. Two 8 x 2.8 mm tunnels take 4.8 mm standard or 7.6 mm heavy-duty zip ties that wrap the tube and pull the groove down onto it.
A standoff bridge that suspends a 40 mm fan directly over a Raspberry Pi 4B / 3B+, with a 32 mm shrouded duct collar aiming the air at the SoC instead of letting it spill sideways. 74 x 64 mm plate on four 18 mm legs that clear the USB/Ethernet stack, 58 x 49 mm M2.5 board pattern with captured nuts at the board end, 32 mm square M3 fan pattern, plus side exhaust vents and a 26 x 4.5 mm slot for GPIO ribbon or camera flex.
A 104 x 46 x 16 mm bench dock that stands up 6 microSD cards (11 x 15 x 1 mm), 3 full-size SD cards (24 x 32 x 2.1 mm) and 4 USB-A flash drives parked plug-down in 12.8 x 5.4 mm bays, so the loose media around a Pi/camera bench stops disappearing into the parts bin. Cards protrude 7–20 mm for a one-finger pinch, a scalloped thumb groove backs the microSD row, and two M3 clearance holes on a 96 mm centre let you screw it into a drawer bottom or shelf; underside relief pockets keep it to roughly 57 cm³.
A clamp-on comb that grips the back edge of a desk or shelf (tops up to 27 mm thick) and drops five cables down in separate channels instead of one tangled bundle — two 10 mm channels for laptop/power bricks and three 7 mm channels for USB and audio leads, each with a snap-in mouth so cables push in from the side and stay put. 57 mm wide, 42 mm tall, no drilling: an M4 brass heat-set insert (5.5 mm bore) in the lower jaw takes an M4 x 20–25 bolt that jacks up against the underside of the desktop.
A split collar that clamps onto a standard 1/2" NPT shower arm (21.3 mm OD pipe) with one M4 screw into a heat-set insert, carrying two 30 mm upturned J-hooks for a loofah, razor strap or bottle handle — no suction cups, no drilling tile. Collar bore is 21.8 mm, ring wall 3.5 mm, overall 60 x 38 x 18 mm; slide it on with the shower head removed, then pinch the 3 mm gap closed to lock it.
A six-lane stadium-step rack that sorts cut heat-shrink tubing by diameter — troughs 8/10/12/14/17/20 mm wide take the common 3:1 sizes from 2.4 mm up to 12.7 mm, each 74 mm long with a finger scallop so you can pinch a piece out without emptying the lane. 116 x 99 x 39 mm overall, open underneath to stay light, with two M4 clearance ears (4.5 mm) to screw it to a shelf or bench back.
A no-screw C-clamp that slides onto a desk edge or shelf and hangs your headphones underneath on a wide 30 mm saddle. The wedged inner jaw self-tightens on tops from 20–30 mm thick, and the 14 mm hook mouth also takes a bag or lanyard.
An 80 mm L-block that holds two boards at a true 90° while glue sets, with open windows so a spring clamp reaches straight through to the workpiece and a rounded corner relief for squeeze-out. Two 4.5 mm holes let you screw it down to a bench or assembly board.
A 147 mm staircase block that stands a 13-piece metric drill index upright, with bores from 1.5 mm to 7.5 mm rising left to right so the size order is obvious at a glance. Each step is taller than the last, so bit tips sit deep and shanks stay easy to grab.