Preview in 3D, we print and ship it — or download the file to print yourself.
Heads up: many models on this page are AI-generated or uploaded untested. They may be misconfigured for the intended application — check the dimensions and tolerances, and verify or edit the model before printing or relying on it.
A 10.8° tilt riser that lifts a desktop speaker or small studio monitor off the desk and aims the tweeter up at ear height — 115 mm deep x 100 mm wide, 12 mm at the rear rising to 34 mm at the front. A 5 mm rear lip stops the cabinet sliding back downhill, four 1.2 mm grip ridges cut contact area for decoupling, and a 14 mm channel through the lip passes the speaker cable. Hollow ribbed shell (2.6 mm skin, 3 mm ribs) so it prints fast and flat with no supports; print two.
A no-drill C-clamp that hooks over the front lip of a K-style rain gutter and carries a security camera or its solar panel on a 13 mm long 1/4-20 slot, so renters and anyone with aluminium soffits never touch the fascia. The 26 mm throat is closed by two M4 screws in 5.5 mm heat-set insert bores (use M4 x 30), gripping lips and beads from 5 to 24 mm deep; overall 74 x 44 mm with a 30 mm wide jaw, and it prints with zero overhangs because the whole profile is extruded along the gutter run.
A screw-clamped replacement tine for a dishwasher rack: a split saddle grips any coated rack wire from 4.6 to 6.6 mm and carries a 48 mm tapered fin that holds plates apart where the original tines snapped or rusted through. 59 x 21 x 36 mm, closed by two M3 x 20 stainless screws into M3 heat-set inserts (4.0 mm bores), with six drain cutouts; print in PETG.
A 145 x 60 x 28 mm screw-up tray that mounts to the underside of a desk to hold a power brick, surge strip and cable slack off the floor. Cables snap in through a 46.8 mm mouth under a 45° retaining lip, both ends are open for pass-through, three vented windows per side let cables exit anywhere, four zip-tie slots strap a brick down, and four raised pads take M4 (or #8) screws in 4.5 mm clearance bores with 8.4 mm counterbores so the heads sit flush below the cables.
A wired-mouse cable bungee whose compliance comes from a printed bow spring: a 2.4 mm x 12 mm leaf arch bends in the XY plane (along the layer lines, not across them) so the 50 mm guide post springs fore-and-aft and keeps drag off the mouse. The 62 x 30 x 5 mm foot sticks down with a VHB square (the spring rides 1 mm clear of the desk) or bolts down through two 4.5 mm M4 clearance holes; the cable snaps into a 6.4 mm trough 43 mm up through a 4.4 mm pinch and still slides freely. Overall 62 x 73 x 50 mm, about 22 cm3 of plastic.
A split-band clamp that grips a standard round door knob (50–56 mm, eleven internal 1.25 mm grip ribs) and adds a 95 mm lever arm so the door opens with a forearm, elbow or closed fist instead of a twisting grip. One M4 bolt through the 4.5 mm clearance ears pulls the 4 mm split shut onto a captured M4 nut; band is 22 mm tall, arm 14 mm thick, overall 139 x 63 mm, and it prints flat with the lever load in the XY plane.
A 114 x 114 mm plate that bolts to a monitor's VESA 75 x 75 or 100 x 100 M4 pattern (sandwiched under the arm/stand screws) and carries a 92 x 50 mm tray with 23 mm side walls and a 7 mm front rail behind the screen. A 62 mm centre window clears the arm head, twin 5 x 16 mm strap slots and a 10 mm cable pass-through hold a USB hub, dongle receiver, SSD or mini PC off the desk.
A split clamp for a 31.8 mm handlebar that carries a second 22.2 mm accessory bar stub 55 mm out to the side, so lights, a GPS, a bell and a phone mount stop fighting for stem space. Closed by two M5 bolts with captured nuts, 99 x 44 x 55 mm, gusseted web under the stub.
A clamp-on shelf that straddles the top bezel of a monitor and gives a webcam, action cam or small light a solid 41 mm deep platform with a 6.8 mm obround slot for a 1/4-20 tripod screw (14 mm of fore/aft travel) and a 3 mm anti-slide lip. The 18 mm wide throat swallows panels from about 5 mm to 18 mm thick and locks with an M4 x 25 screw into an M4 heat-set insert (5.5 mm bore) in the rear jaw, so nothing presses on the screen; two M3 clearance holes in the deck take a light arm or adapter plate. Overall 78 x 34 x 42 mm, printed as a single profile with no overhangs or supports.
A C-clamp that grips a desktop 12–30 mm thick and holds a vertical 2020 extrusion post at the desk edge, so you can mount a lamp, mic boom, webcam or a small shelf without drilling the desk. 99 x 38 x 30 mm body with a 20.4 mm square socket 40 mm deep (two M5 clearance holes for T-nuts lock the post) and two M4 heat-set inserts in the lower jaw for the M4x30 clamp bolts; the flat 38 x 30 mm upper jaw pad bears on the desk surface and the rear face registers flush against the desk edge. Prints flat on the plate, no supports.
A bolt-clamped replacement slider/holder for a 25 mm shower riser bar, for when the molded plastic holder cracks and the maker only sells the whole $60 rail. A 38 mm split ring with 6.3 mm walls grips the bar via two M5x30 bolts with captured nut pockets, and a 10°-tilted tapered cradle (26.4 mm top, 22.8 mm bottom, open through the bottom so it drains) holds the hand shower. Overall 90 x 39 x 32 mm.
A cable-tie-on bottle cage mount for bikes with no braze-on bosses: a 26 x 26 x 90 mm block with a 90-degree V groove that self-centres on round tubes from about 22 to 32 mm, and two M5 cage bolt bores on the standard 64 mm boss spacing with captured 8 mm hex nuts loaded from the side. Two 8 x 2.8 mm tunnels take 4.8 mm standard or 7.6 mm heavy-duty zip ties that wrap the tube and pull the groove down onto it.
A 20° angled stand that tilts a solderless breadboard toward you for better wiring visibility, with a 163 x 25 x 7 mm parts trough in front for resistors and jumpers. The 172 mm wide deck takes a full-size 830-point board or two half-size boards, held by a 4 mm front lip and an 8 mm rear backstop with three 14 mm notches for jumper bundles; two M3 clearance tabs let you screw it to the bench. Overall 172 x 108 x 38 mm, open-ribbed underneath so it prints without supports.
A 104 x 46 x 16 mm bench dock that stands up 6 microSD cards (11 x 15 x 1 mm), 3 full-size SD cards (24 x 32 x 2.1 mm) and 4 USB-A flash drives parked plug-down in 12.8 x 5.4 mm bays, so the loose media around a Pi/camera bench stops disappearing into the parts bin. Cards protrude 7–20 mm for a one-finger pinch, a scalloped thumb groove backs the microSD row, and two M3 clearance holes on a 96 mm centre let you screw it into a drawer bottom or shelf; underside relief pockets keep it to roughly 57 cm³.
A clamp-on comb that grips the back edge of a desk or shelf (tops up to 27 mm thick) and drops five cables down in separate channels instead of one tangled bundle — two 10 mm channels for laptop/power bricks and three 7 mm channels for USB and audio leads, each with a snap-in mouth so cables push in from the side and stay put. 57 mm wide, 42 mm tall, no drilling: an M4 brass heat-set insert (5.5 mm bore) in the lower jaw takes an M4 x 20–25 bolt that jacks up against the underside of the desktop.
A split collar that clamps onto a standard 1/2" NPT shower arm (21.3 mm OD pipe) with one M4 screw into a heat-set insert, carrying two 30 mm upturned J-hooks for a loofah, razor strap or bottle handle — no suction cups, no drilling tile. Collar bore is 21.8 mm, ring wall 3.5 mm, overall 60 x 38 x 18 mm; slide it on with the shower head removed, then pinch the 3 mm gap closed to lock it.
A desk dock with a recessed tray sized for a standard 76 x 76 mm sticky note pad and a rounded rear trough for pens, pencils and erasers. A scalloped thumb notch in the front wall lets you peel notes one-handed; footprint is 86 x 113 mm and 20 mm tall.
A 95 x 70 mm catch-all tray with two compartments for keys and coins plus an upright slot that stands a phone (up to 13 mm thick with case) face-up on a raised shelf. A tunnel through the back wall feeds the charging cable up to the phone's port so the cord never leaves the dock.
A hollow, rib-cored riser that lifts a bed, couch, desk or dresser leg 44 mm for extra under-furniture storage. The chamfered 58 mm socket accepts square or round legs, and a poke-out hole in the floor frees a stuck leg — order four for one piece of furniture.
A three-step cabinet riser that stair-steps spice jars so every label is visible from the front. 80 mm wide x 108 mm deep x 66 mm tall, with a 3 mm lip on each tread so jars can't slide off; hollow open-bottom shell with internal ribs to keep it light.
A no-screw C-clamp that slides onto a desk edge or shelf and hangs your headphones underneath on a wide 30 mm saddle. The wedged inner jaw self-tightens on tops from 20–30 mm thick, and the 14 mm hook mouth also takes a bag or lanyard.
An 80 mm L-block that holds two boards at a true 90° while glue sets, with open windows so a spring clamp reaches straight through to the workpiece and a rounded corner relief for squeeze-out. Two 4.5 mm holes let you screw it down to a bench or assembly board.
A 78 mm-deep pen and pencil cup with a 15°-reclined phone cradle built onto one side, sized for phones up to 13.5 mm thick with a case. A slot through the floor and front lip lets a charging cable reach the port while the phone is docked.
A weighted-footprint cradle that holds a closed laptop, tablet or notebook upright on the desk, with a 22 mm slot, chamfered lead-in edges and a cable pass-through slot in the floor. 90 × 70 × 50 mm.