Preview in 3D, we print and ship it — or download the file to print yourself.
Heads up: many models on this page are AI-generated or uploaded untested. They may be misconfigured for the intended application — check the dimensions and tolerances, and verify or edit the model before printing or relying on it.
A 114 x 114 mm plate that bolts to a monitor's VESA 75 x 75 or 100 x 100 M4 pattern (sandwiched under the arm/stand screws) and carries a 92 x 50 mm tray with 23 mm side walls and a 7 mm front rail behind the screen. A 62 mm centre window clears the arm head, twin 5 x 16 mm strap slots and a 10 mm cable pass-through hold a USB hub, dongle receiver, SSD or mini PC off the desk.
A split clamp for a 31.8 mm handlebar that carries a second 22.2 mm accessory bar stub 55 mm out to the side, so lights, a GPS, a bell and a phone mount stop fighting for stem space. Closed by two M5 bolts with captured nuts, 99 x 44 x 55 mm, gusseted web under the stub.
A print-in-place four-bar over-center toggle clamp (125 x 46 x 26 mm) that pushes a 24 mm wide pad sideways to lock a workpiece against a fence — handle, coupler, arm and base all print as one piece on printed pivot pins with 0.5 mm clearances. The base bolts down with two M5 clearance holes plus two 20 mm M5 slots so the clamp can be slid to the work on a T-track, 2020 rail or drilled bench top.
A clamp-on shelf that straddles the top bezel of a monitor and gives a webcam, action cam or small light a solid 41 mm deep platform with a 6.8 mm obround slot for a 1/4-20 tripod screw (14 mm of fore/aft travel) and a 3 mm anti-slide lip. The 18 mm wide throat swallows panels from about 5 mm to 18 mm thick and locks with an M4 x 25 screw into an M4 heat-set insert (5.5 mm bore) in the rear jaw, so nothing presses on the screen; two M3 clearance holes in the deck take a light arm or adapter plate. Overall 78 x 34 x 42 mm, printed as a single profile with no overhangs or supports.
A weather cap for a nominal 4x4 fence or deck post (88.9 mm actual) with a 91 mm square socket, 20 mm engagement and two M4 clearance holes so it screws down and won't blow off. Twin horns on opposite faces carry a cafe-string-light cable in an 8 mm wide, 10 mm deep slot; overall 127 x 97 x 50 mm with a hollow 50-degree pyramid roof that sheds water and prints support-free.
A C-clamp that grips a desktop 12–30 mm thick and holds a vertical 2020 extrusion post at the desk edge, so you can mount a lamp, mic boom, webcam or a small shelf without drilling the desk. 99 x 38 x 30 mm body with a 20.4 mm square socket 40 mm deep (two M5 clearance holes for T-nuts lock the post) and two M4 heat-set inserts in the lower jaw for the M4x30 clamp bolts; the flat 38 x 30 mm upper jaw pad bears on the desk surface and the rear face registers flush against the desk edge. Prints flat on the plate, no supports.
A bolt-clamped replacement slider/holder for a 25 mm shower riser bar, for when the molded plastic holder cracks and the maker only sells the whole $60 rail. A 38 mm split ring with 6.3 mm walls grips the bar via two M5x30 bolts with captured nut pockets, and a 10°-tilted tapered cradle (26.4 mm top, 22.8 mm bottom, open through the bottom so it drains) holds the hand shower. Overall 90 x 39 x 32 mm.
A clamp-on double hook that saddles the top edge of a frameless glass shower door — towel hook on the outside, loofah/razor hook on the inside, no drilling, adhesive or suction cup. The 13.6 mm slot with a raised grip pad takes 6–13 mm (1/4"–1/2") tempered glass, and an M4 heat-set insert (5.5 mm bore) plus an M4x16 screw locks it down; 76 x 43 x 26 mm.
A cable-tie-on bottle cage mount for bikes with no braze-on bosses: a 26 x 26 x 90 mm block with a 90-degree V groove that self-centres on round tubes from about 22 to 32 mm, and two M5 cage bolt bores on the standard 64 mm boss spacing with captured 8 mm hex nuts loaded from the side. Two 8 x 2.8 mm tunnels take 4.8 mm standard or 7.6 mm heavy-duty zip ties that wrap the tube and pull the groove down onto it.
A three-piece print-in-place cam cleat that jams 4–8 mm rope or paracord one-way for tarps, roof racks, awnings and van-life tie-downs — pull to tension, lift the line out to release. Base is 76 x 54 x 16 mm with four 5.5 mm M5 clearance holes on a 60 x 42 mm rectangle; the two toothed cams ride on 6 mm printed pins with retaining heads and are closed by 1.2 mm curved flexure springs, with 4.5 mm guide ribs fairleading the line in.
A 20° angled stand that tilts a solderless breadboard toward you for better wiring visibility, with a 163 x 25 x 7 mm parts trough in front for resistors and jumpers. The 172 mm wide deck takes a full-size 830-point board or two half-size boards, held by a 4 mm front lip and an 8 mm rear backstop with three 14 mm notches for jumper bundles; two M3 clearance tabs let you screw it to the bench. Overall 172 x 108 x 38 mm, open-ribbed underneath so it prints without supports.
A 104 x 46 x 16 mm bench dock that stands up 6 microSD cards (11 x 15 x 1 mm), 3 full-size SD cards (24 x 32 x 2.1 mm) and 4 USB-A flash drives parked plug-down in 12.8 x 5.4 mm bays, so the loose media around a Pi/camera bench stops disappearing into the parts bin. Cards protrude 7–20 mm for a one-finger pinch, a scalloped thumb groove backs the microSD row, and two M3 clearance holes on a 96 mm centre let you screw it into a drawer bottom or shelf; underside relief pockets keep it to roughly 57 cm³.
A clamp-on comb that grips the back edge of a desk or shelf (tops up to 27 mm thick) and drops five cables down in separate channels instead of one tangled bundle — two 10 mm channels for laptop/power bricks and three 7 mm channels for USB and audio leads, each with a snap-in mouth so cables push in from the side and stay put. 57 mm wide, 42 mm tall, no drilling: an M4 brass heat-set insert (5.5 mm bore) in the lower jaw takes an M4 x 20–25 bolt that jacks up against the underside of the desktop.
A split collar that clamps onto a standard 1/2" NPT shower arm (21.3 mm OD pipe) with one M4 screw into a heat-set insert, carrying two 30 mm upturned J-hooks for a loofah, razor strap or bottle handle — no suction cups, no drilling tile. Collar bore is 21.8 mm, ring wall 3.5 mm, overall 60 x 38 x 18 mm; slide it on with the shower head removed, then pinch the 3 mm gap closed to lock it.
A print-in-place hinged tilt bracket for small 10–100 W solar panels, 140 x 60 mm with a 5 mm base plate and a 60 mm-tall detent post. The base bolts to a roof rail, van rack or shed wall with four M5 lag screws (5.5 mm clearance holes) and the panel wing takes four M5 frame bolts; a single M5 x 60 bolt through the post and quadrant fin locks the tilt at 15°, 30°, 45° or 60°, with strap slots on both plates for frameless panels.
A U-bracket that slips over a cabinet door (fits panels up to 19.5 mm thick) and turns the inside face into a grocery-bag trash caddy — the bag handles drop into a 9 mm trough behind an upturned lip so they can't slide off. 50 mm wide with two optional screw holes for a permanent mount.
A desk dock with a recessed tray sized for a standard 76 x 76 mm sticky note pad and a rounded rear trough for pens, pencils and erasers. A scalloped thumb notch in the front wall lets you peel notes one-handed; footprint is 86 x 113 mm and 20 mm tall.
A 95 x 70 mm catch-all tray with two compartments for keys and coins plus an upright slot that stands a phone (up to 13 mm thick with case) face-up on a raised shelf. A tunnel through the back wall feeds the charging cable up to the phone's port so the cord never leaves the dock.
A no-screw C-clamp that slides onto a desk edge or shelf and hangs your headphones underneath on a wide 30 mm saddle. The wedged inner jaw self-tightens on tops from 20–30 mm thick, and the 14 mm hook mouth also takes a bag or lanyard.
A 78 mm-deep pen and pencil cup with a 15°-reclined phone cradle built onto one side, sized for phones up to 13.5 mm thick with a case. A slot through the floor and front lip lets a charging cable reach the port while the phone is docked.
A weighted-footprint cradle that holds a closed laptop, tablet or notebook upright on the desk, with a 22 mm slot, chamfered lead-in edges and a cable pass-through slot in the floor. 90 × 70 × 50 mm.
A print-in-place matchbox-style stash box: a fixed outer sleeve with a drawer that slides in and out to store small items like SD cards, paperclips, or jewelry. Prints fully assembled, ~84 x 44 x 22 mm.