Preview in 3D, we print and ship it — or download the file to print yourself.
Heads up: many models on this page are AI-generated or uploaded untested. They may be misconfigured for the intended application — check the dimensions and tolerances, and verify or edit the model before printing or relying on it.
A split clamp for a 31.8 mm handlebar that carries a second 22.2 mm accessory bar stub 55 mm out to the side, so lights, a GPS, a bell and a phone mount stop fighting for stem space. Closed by two M5 bolts with captured nuts, 99 x 44 x 55 mm, gusseted web under the stub.
A print-in-place four-bar over-center toggle clamp (125 x 46 x 26 mm) that pushes a 24 mm wide pad sideways to lock a workpiece against a fence — handle, coupler, arm and base all print as one piece on printed pivot pins with 0.5 mm clearances. The base bolts down with two M5 clearance holes plus two 20 mm M5 slots so the clamp can be slid to the work on a T-track, 2020 rail or drilled bench top.
A bench-top fume extractor housing for any 40 x 40 x 10 mm fan — the fan bolts to the 60°-tilted face on its standard 32 mm M3 pattern (3.4 mm clearance holes with counterbores so the heads sit flush), and a 42 mm square of activated-carbon filter sheet press-fits into the 41.5 x 41.5 x 4 mm pocket in front of a ribbed finger-guard throat. Footprint 52 x 64 mm, 50 mm tall, with two M4 holes in the weighted base for bolting it to the bench and an open rear duct so exhaust clears the work.
A weather cap for a nominal 4x4 fence or deck post (88.9 mm actual) with a 91 mm square socket, 20 mm engagement and two M4 clearance holes so it screws down and won't blow off. Twin horns on opposite faces carry a cafe-string-light cable in an 8 mm wide, 10 mm deep slot; overall 127 x 97 x 50 mm with a hollow 50-degree pyramid roof that sheds water and prints support-free.
A bolt-clamped replacement slider/holder for a 25 mm shower riser bar, for when the molded plastic holder cracks and the maker only sells the whole $60 rail. A 38 mm split ring with 6.3 mm walls grips the bar via two M5x30 bolts with captured nut pockets, and a 10°-tilted tapered cradle (26.4 mm top, 22.8 mm bottom, open through the bottom so it drains) holds the hand shower. Overall 90 x 39 x 32 mm.
A clamp-on double hook that saddles the top edge of a frameless glass shower door — towel hook on the outside, loofah/razor hook on the inside, no drilling, adhesive or suction cup. The 13.6 mm slot with a raised grip pad takes 6–13 mm (1/4"–1/2") tempered glass, and an M4 heat-set insert (5.5 mm bore) plus an M4x16 screw locks it down; 76 x 43 x 26 mm.
A cable-tie-on bottle cage mount for bikes with no braze-on bosses: a 26 x 26 x 90 mm block with a 90-degree V groove that self-centres on round tubes from about 22 to 32 mm, and two M5 cage bolt bores on the standard 64 mm boss spacing with captured 8 mm hex nuts loaded from the side. Two 8 x 2.8 mm tunnels take 4.8 mm standard or 7.6 mm heavy-duty zip ties that wrap the tube and pull the groove down onto it.
A three-piece print-in-place cam cleat that jams 4–8 mm rope or paracord one-way for tarps, roof racks, awnings and van-life tie-downs — pull to tension, lift the line out to release. Base is 76 x 54 x 16 mm with four 5.5 mm M5 clearance holes on a 60 x 42 mm rectangle; the two toothed cams ride on 6 mm printed pins with retaining heads and are closed by 1.2 mm curved flexure springs, with 4.5 mm guide ribs fairleading the line in.
A print-in-place PCB soldering vise: a 110 x 38 x 8 mm base rail with a captive T-slot jaw that slides along it, holding boards from 15 mm to 79 mm wide in a pair of 2.6 mm edge grooves (sized for 1.6 mm FR4). An M4 self-tapping screw through the sliding jaw jacks against the rail floor to lock it; four 4.5 mm M4 clearance holes bolt the rail to a bench or plate.
A split collar that clamps onto a standard 1/2" NPT shower arm (21.3 mm OD pipe) with one M4 screw into a heat-set insert, carrying two 30 mm upturned J-hooks for a loofah, razor strap or bottle handle — no suction cups, no drilling tile. Collar bore is 21.8 mm, ring wall 3.5 mm, overall 60 x 38 x 18 mm; slide it on with the shower head removed, then pinch the 3 mm gap closed to lock it.
A print-in-place hinged tilt bracket for small 10–100 W solar panels, 140 x 60 mm with a 5 mm base plate and a 60 mm-tall detent post. The base bolts to a roof rail, van rack or shed wall with four M5 lag screws (5.5 mm clearance holes) and the panel wing takes four M5 frame bolts; a single M5 x 60 bolt through the post and quadrant fin locks the tilt at 15°, 30°, 45° or 60°, with strap slots on both plates for frameless panels.
A 115 x 70 mm bench caddy for a soldering station: twin V-yokes cradle the iron by its handle (notch accepts 8–24 mm grips) at a 25° tip-up angle so the hot tip hangs ~90 mm clear in free air, never touching plastic. Includes a 41 mm ID x 30 mm deep brass-wool cup, four 6.5 mm spare-tip holes plus an 11 mm flux-pen pocket, a 9 mm snap-in cable keeper for the iron lead, and two M4 clearance holes to bolt it to the bench. Print in PETG if your iron runs hot.
A tapered 1-cup (240 ml) scoop for dog food, birdseed, coffee beans or detergent, with a flat base so it stands on the counter and a 10 mm hole in the angled handle to hang it on a hook. Bowl is 129 mm long with 2.4 mm walls.
A U-bracket that slips over a cabinet door (fits panels up to 19.5 mm thick) and turns the inside face into a grocery-bag trash caddy — the bag handles drop into a 9 mm trough behind an upturned lip so they can't slide off. 50 mm wide with two optional screw holes for a permanent mount.
A no-screw C-clamp that slides onto a desk edge or shelf and hangs your headphones underneath on a wide 30 mm saddle. The wedged inner jaw self-tightens on tops from 20–30 mm thick, and the 14 mm hook mouth also takes a bag or lanyard.