Preview in 3D, we print and ship it — or download the file to print yourself.
Heads up: many models on this page are AI-generated or uploaded untested. They may be misconfigured for the intended application — check the dimensions and tolerances, and verify or edit the model before printing or relying on it.
A weather cap for a nominal 4x4 fence or deck post (88.9 mm actual) with a 91 mm square socket, 20 mm engagement and two M4 clearance holes so it screws down and won't blow off. Twin horns on opposite faces carry a cafe-string-light cable in an 8 mm wide, 10 mm deep slot; overall 127 x 97 x 50 mm with a hollow 50-degree pyramid roof that sheds water and prints support-free.
A clamp-on double hook that saddles the top edge of a frameless glass shower door — towel hook on the outside, loofah/razor hook on the inside, no drilling, adhesive or suction cup. The 13.6 mm slot with a raised grip pad takes 6–13 mm (1/4"–1/2") tempered glass, and an M4 heat-set insert (5.5 mm bore) plus an M4x16 screw locks it down; 76 x 43 x 26 mm.
A standoff bridge that suspends a 40 mm fan directly over a Raspberry Pi 4B / 3B+, with a 32 mm shrouded duct collar aiming the air at the SoC instead of letting it spill sideways. 74 x 64 mm plate on four 18 mm legs that clear the USB/Ethernet stack, 58 x 49 mm M2.5 board pattern with captured nuts at the board end, 32 mm square M3 fan pattern, plus side exhaust vents and a 26 x 4.5 mm slot for GPIO ribbon or camera flex.
A split collar that clamps onto a standard 1/2" NPT shower arm (21.3 mm OD pipe) with one M4 screw into a heat-set insert, carrying two 30 mm upturned J-hooks for a loofah, razor strap or bottle handle — no suction cups, no drilling tile. Collar bore is 21.8 mm, ring wall 3.5 mm, overall 60 x 38 x 18 mm; slide it on with the shower head removed, then pinch the 3 mm gap closed to lock it.
A 28 mm tall tapered duct that lets a 60 mm fan feed an 80 mm fan opening (or vice versa): 80 x 80 mm flange with M4 clearance holes on the 71.5 mm pattern at the bottom, 60 x 60 mm face with four 3.4 mm self-tapping M4 bosses on the 50 mm pattern on top. The airway necks smoothly from 73 mm to 55 mm with a 2 mm wall, so it replaces a grinder/zip-tie bodge on amp racks, 3D-printer electronics bays and PC cases.
A U-bracket that slips over a cabinet door (fits panels up to 19.5 mm thick) and turns the inside face into a grocery-bag trash caddy — the bag handles drop into a 9 mm trough behind an upturned lip so they can't slide off. 50 mm wide with two optional screw holes for a permanent mount.
A handheld drill guide with five tall bushing towers (3.2, 4.2, 5.2, 6.4 and 8.2 mm) that keep a bit perfectly perpendicular, plus a 90° V-groove underside that self-centers the holes on dowels and round stock. Block is 102 x 36 x 44 mm.
A 95 x 70 mm catch-all tray with two compartments for keys and coins plus an upright slot that stands a phone (up to 13 mm thick with case) face-up on a raised shelf. A tunnel through the back wall feeds the charging cable up to the phone's port so the cord never leaves the dock.
A no-screw C-clamp that slides onto a desk edge or shelf and hangs your headphones underneath on a wide 30 mm saddle. The wedged inner jaw self-tightens on tops from 20–30 mm thick, and the 14 mm hook mouth also takes a bag or lanyard.
A two-horn wall cleat for figure-eight wrapping an extension cord, air hose or rope, with flared post tips that keep the coil from slipping off. 120 mm wide, mounts with two countersunk screws and holds roughly a 50 ft 16-gauge cord.