Preview in 3D, we print and ship it — or download the file to print yourself.
Heads up: many models on this page are AI-generated or uploaded untested. They may be misconfigured for the intended application — check the dimensions and tolerances, and verify or edit the model before printing or relying on it.
Replacement bottom guide for a bypass/sliding shower door: a 46 x 22 x 15 mm block that screws to the track with two countersunk M3 (#6) screws and carries the door's bottom glass edge in a 7.2 mm channel sized for 1/4 in (6.35 mm) glass. A V-shaped lead-in opens the channel to 12.7 mm at the rim so 5/16 in and 3/8 in glass still ride about 5 mm deep, and flared ends in plan view guide a drifting door back in; the counterbored screw holes also drain the channel.
Replacement wall-end bracket for a broken towel bar, with a stepped socket that takes both 1 in (25.4 mm) and 3/4 in (19 mm) tube — a 1 in bar bottoms on the step after 18 mm, a 3/4 in bar slides 28 mm deep — and an M4 set screw that locks it so you don't have to replace the whole rail set. Back plate is 42 x 68 x 6 mm with two counterbored 4.5 mm holes 52 mm apart for #8/M4 anchors, bar centre stands 38 mm off the wall, overall 55 mm tall.
A 120 mm replacement flush lever arm for a toilet tank, for when the brittle OEM arm snaps at the chain hole and the linkage isn't sold separately. Instead of guessing your handle's tab shape, a 14 mm deep forked jaw slides over the handle blade (1.5–3.6 mm thick) and pinches it with an M3×20 screw and a captured M3 nut; five 4 mm chain holes on a 12 mm pitch set the flapper chain length. Arm cross-section is 5 × 12 mm so the bending load runs along the print's strong axis.
A bolt-clamped replacement slider/holder for a 25 mm shower riser bar, for when the molded plastic holder cracks and the maker only sells the whole $60 rail. A 38 mm split ring with 6.3 mm walls grips the bar via two M5x30 bolts with captured nut pockets, and a 10°-tilted tapered cradle (26.4 mm top, 22.8 mm bottom, open through the bottom so it drains) holds the hand shower. Overall 90 x 39 x 32 mm.
A 120 mm slide-on splint sleeve that repairs a snapped 11 mm tent pole section: 11.4 mm teardrop bore (0.4 mm slip fit), 4 mm walls, tapered lead-in mouths at both ends, and two M3 self-tapping set-screw bosses (2.6 mm holes) that pin it to each pole half so it can't migrate off the break. A centre notch in the full-length stiffening rib lines it up on the crack; overall 120 x 19.4 x 22 mm with a flat printed pad on the bottom. Print in PETG or ASA for UV and cold tolerance.
A 144 mm desk plate with three real meshing gears — a 24-tooth crank wheel with a domed finger knob driving two 14-tooth pinions, all captured on mushroom-cap posts. Prints fully assembled, no supports: four separate pieces, 0.45 mm clearance everywhere, spin the knob and the whole train turns.
A 139 mm print-in-place centipede: eight leg-bearing body segments joined by seven captured ball-and-socket joints, so the whole body ripples and curls in your hand. Prints fully assembled, flat on the plate, no supports and no assembly.
A countertop vanity dispenser: a 61 mm tube that stacks standard cotton rounds with a full-height front slot so you can see the level and pull one out with a thumb, plus an attached 28 mm cup for cotton swabs. Footprint 98 x 66 mm, 82 mm tall.