Preview in 3D, we print and ship it — or download the file to print yourself.
Heads up: many models on this page are AI-generated or uploaded untested. They may be misconfigured for the intended application — check the dimensions and tolerances, and verify or edit the model before printing or relying on it.
A split clamp for a 31.8 mm handlebar that carries a second 22.2 mm accessory bar stub 55 mm out to the side, so lights, a GPS, a bell and a phone mount stop fighting for stem space. Closed by two M5 bolts with captured nuts, 99 x 44 x 55 mm, gusseted web under the stub.
A print-in-place four-bar over-center toggle clamp (125 x 46 x 26 mm) that pushes a 24 mm wide pad sideways to lock a workpiece against a fence — handle, coupler, arm and base all print as one piece on printed pivot pins with 0.5 mm clearances. The base bolts down with two M5 clearance holes plus two 20 mm M5 slots so the clamp can be slid to the work on a T-track, 2020 rail or drilled bench top.
A print-in-place eccentric cam clamp that drops into a 3/4 in (19.05 mm) bench dog hole and twists to pin work against a fence or a second dog — 5 mm of cam throw past the 24 mm collar stop, for stock 9 mm thick and up. The 19.2 mm shank is bored and split into two spring tabs so it grips the hole instead of rattling; 41.4 mm tall, 26 mm knob, two pieces printed as one assembly with 0.5 mm clearances (print with a brim, no supports).
A weather cap for a nominal 4x4 fence or deck post (88.9 mm actual) with a 91 mm square socket, 20 mm engagement and two M4 clearance holes so it screws down and won't blow off. Twin horns on opposite faces carry a cafe-string-light cable in an 8 mm wide, 10 mm deep slot; overall 127 x 97 x 50 mm with a hollow 50-degree pyramid roof that sheds water and prints support-free.
A one-piece dust-extraction adapter that joins a 2-1/2 in (63.5 mm) shop-vac hose to a 1-1/4 in (31.75 mm) power-tool dust port — a 64.0 mm socket with an internal 45° stop shoulder steps down through a tapered cone to a 31.4→30.6 mm friction spigot with a seating flange. 79 mm tall, 78 mm across the three grip ribs, with a 3.4 mm M4 self-tapping screw hole through one rib so the hose can be locked instead of pulling off mid-cut.
A bolt-clamped replacement slider/holder for a 25 mm shower riser bar, for when the molded plastic holder cracks and the maker only sells the whole $60 rail. A 38 mm split ring with 6.3 mm walls grips the bar via two M5x30 bolts with captured nut pockets, and a 10°-tilted tapered cradle (26.4 mm top, 22.8 mm bottom, open through the bottom so it drains) holds the hand shower. Overall 90 x 39 x 32 mm.
A clamp-on double hook that saddles the top edge of a frameless glass shower door — towel hook on the outside, loofah/razor hook on the inside, no drilling, adhesive or suction cup. The 13.6 mm slot with a raised grip pad takes 6–13 mm (1/4"–1/2") tempered glass, and an M4 heat-set insert (5.5 mm bore) plus an M4x16 screw locks it down; 76 x 43 x 26 mm.
A cable-tie-on bottle cage mount for bikes with no braze-on bosses: a 26 x 26 x 90 mm block with a 90-degree V groove that self-centres on round tubes from about 22 to 32 mm, and two M5 cage bolt bores on the standard 64 mm boss spacing with captured 8 mm hex nuts loaded from the side. Two 8 x 2.8 mm tunnels take 4.8 mm standard or 7.6 mm heavy-duty zip ties that wrap the tube and pull the groove down onto it.
A three-piece print-in-place cam cleat that jams 4–8 mm rope or paracord one-way for tarps, roof racks, awnings and van-life tie-downs — pull to tension, lift the line out to release. Base is 76 x 54 x 16 mm with four 5.5 mm M5 clearance holes on a 60 x 42 mm rectangle; the two toothed cams ride on 6 mm printed pins with retaining heads and are closed by 1.2 mm curved flexure springs, with 4.5 mm guide ribs fairleading the line in.
A double-ended bearing press tool for an M8 threaded-rod press: one end is a Ø21.5 mm drift whose 19.2–21.5 mm annular face lands only on a 608 bearing's outer race (never the shield), the other end is a stepped receiver cup (Ø24 mm × 12 mm deep, stepping to Ø17 mm) that catches a 608, 625 or 624 as it comes out. 44 mm tall, Ø32 mm scalloped grip body, 8.3 mm through bore for M8 all-thread — print two copies to have a drift and a receiver on the rod at once.
A wall-mount rack that snap-holds two standard 65 mm (2.5 in) aerosol rattle cans horizontally by their bodies, with two small side clips that keep the red spray straws with the cans instead of lost in a drawer. The 152 x 76 mm backplate screws to a stud with two M4/#8 screws on a 52 mm vertical spacing (4.5 mm clearance holes, counterbored so heads sit flush), and the 65.6 mm C-clips wrap 223 degrees with a 61 mm mouth so cans push up and click in; cut-out windows behind each can keep it light at ~65 cm3.
A split collar that clamps onto a standard 1/2" NPT shower arm (21.3 mm OD pipe) with one M4 screw into a heat-set insert, carrying two 30 mm upturned J-hooks for a loofah, razor strap or bottle handle — no suction cups, no drilling tile. Collar bore is 21.8 mm, ring wall 3.5 mm, overall 60 x 38 x 18 mm; slide it on with the shower head removed, then pinch the 3 mm gap closed to lock it.
A print-in-place hinged tilt bracket for small 10–100 W solar panels, 140 x 60 mm with a 5 mm base plate and a 60 mm-tall detent post. The base bolts to a roof rail, van rack or shed wall with four M5 lag screws (5.5 mm clearance holes) and the panel wing takes four M5 frame bolts; a single M5 x 60 bolt through the post and quadrant fin locks the tilt at 15°, 30°, 45° or 60°, with strap slots on both plates for frameless panels.
A U-bracket that slips over a cabinet door (fits panels up to 19.5 mm thick) and turns the inside face into a grocery-bag trash caddy — the bag handles drop into a 9 mm trough behind an upturned lip so they can't slide off. 50 mm wide with two optional screw holes for a permanent mount.
A curved clip that wedges onto the rim of a 1-gallon paint can, giving you a clean edge to wipe your brush on and a slot to park it over the paint instead of on the rim. Spans a 50° arc of the can, about 74 mm wide.
A sealed shop bank that swallows used utility-knife blades, snap-off tips and razor blades through a narrow funneled slot in its peaked roof, so they never end up loose in a drawer or trash bag. 58 x 42 mm footprint, 54 mm tall, holds a few hundred blades before you tape the slot and dispose of the whole thing.
A working barrel-bolt latch that prints fully assembled — the red bolt slides inside the grey housing with 0.4 mm clearance, no assembly and no supports. 76 mm housing with four screw ears; the bolt throws 27 mm past the end to catch a cabinet, shed door, gate, or toy box.
A slip-on soft jaw cap for a bench vise: the tapered channel wedges onto jaw plates 12.5–16.5 mm thick, and crossed 90° V-grooves cradle round bar either horizontally or standing upright. 80 mm long, 30 mm tall — print two, one for each jaw.
A no-screw C-clamp that slides onto a desk edge or shelf and hangs your headphones underneath on a wide 30 mm saddle. The wedged inner jaw self-tightens on tops from 20–30 mm thick, and the 14 mm hook mouth also takes a bag or lanyard.
A two-horn wall cleat for figure-eight wrapping an extension cord, air hose or rope, with flared post tips that keep the coil from slipping off. 120 mm wide, mounts with two countersunk screws and holds roughly a 50 ft 16-gauge cord.
A 147 mm staircase block that stands a 13-piece metric drill index upright, with bores from 1.5 mm to 7.5 mm rising left to right so the size order is obvious at a glance. Each step is taller than the last, so bit tips sit deep and shanks stay easy to grab.
A screw-on wall gripper whose springy C-jaws snap over a 20–26 mm broom, mop, rake or squeegee handle so it hangs off the floor. 60 mm back plate with two counterbored screw holes; 18 mm tall jaws with a 19 mm snap mouth.
A wall or pegboard-mountable rail with eight graduated blind holes (8-16mm) that hold metric sockets by friction, keeping them lined up and visible on a workbench. Overall size 150 x 30 x 14mm with two mounting holes for screws.