Preview in 3D, we print and ship it — or download the file to print yourself.
Heads up: many models on this page are AI-generated or uploaded untested. They may be misconfigured for the intended application — check the dimensions and tolerances, and verify or edit the model before printing or relying on it.
A print-in-place eccentric cam clamp that drops into a 3/4 in (19.05 mm) bench dog hole and twists to pin work against a fence or a second dog — 5 mm of cam throw past the 24 mm collar stop, for stock 9 mm thick and up. The 19.2 mm shank is bored and split into two spring tabs so it grips the hole instead of rattling; 41.4 mm tall, 26 mm knob, two pieces printed as one assembly with 0.5 mm clearances (print with a brim, no supports).
A weather cap for a nominal 4x4 fence or deck post (88.9 mm actual) with a 91 mm square socket, 20 mm engagement and two M4 clearance holes so it screws down and won't blow off. Twin horns on opposite faces carry a cafe-string-light cable in an 8 mm wide, 10 mm deep slot; overall 127 x 97 x 50 mm with a hollow 50-degree pyramid roof that sheds water and prints support-free.
A one-piece dust-extraction adapter that joins a 2-1/2 in (63.5 mm) shop-vac hose to a 1-1/4 in (31.75 mm) power-tool dust port — a 64.0 mm socket with an internal 45° stop shoulder steps down through a tapered cone to a 31.4→30.6 mm friction spigot with a seating flange. 79 mm tall, 78 mm across the three grip ribs, with a 3.4 mm M4 self-tapping screw hole through one rib so the hose can be locked instead of pulling off mid-cut.
A clamp-on double hook that saddles the top edge of a frameless glass shower door — towel hook on the outside, loofah/razor hook on the inside, no drilling, adhesive or suction cup. The 13.6 mm slot with a raised grip pad takes 6–13 mm (1/4"–1/2") tempered glass, and an M4 heat-set insert (5.5 mm bore) plus an M4x16 screw locks it down; 76 x 43 x 26 mm.
A double-ended bearing press tool for an M8 threaded-rod press: one end is a Ø21.5 mm drift whose 19.2–21.5 mm annular face lands only on a 608 bearing's outer race (never the shield), the other end is a stepped receiver cup (Ø24 mm × 12 mm deep, stepping to Ø17 mm) that catches a 608, 625 or 624 as it comes out. 44 mm tall, Ø32 mm scalloped grip body, 8.3 mm through bore for M8 all-thread — print two copies to have a drift and a receiver on the rod at once.
A wall-mount rack that snap-holds two standard 65 mm (2.5 in) aerosol rattle cans horizontally by their bodies, with two small side clips that keep the red spray straws with the cans instead of lost in a drawer. The 152 x 76 mm backplate screws to a stud with two M4/#8 screws on a 52 mm vertical spacing (4.5 mm clearance holes, counterbored so heads sit flush), and the 65.6 mm C-clips wrap 223 degrees with a 61 mm mouth so cans push up and click in; cut-out windows behind each can keep it light at ~65 cm3.
A split collar that clamps onto a standard 1/2" NPT shower arm (21.3 mm OD pipe) with one M4 screw into a heat-set insert, carrying two 30 mm upturned J-hooks for a loofah, razor strap or bottle handle — no suction cups, no drilling tile. Collar bore is 21.8 mm, ring wall 3.5 mm, overall 60 x 38 x 18 mm; slide it on with the shower head removed, then pinch the 3 mm gap closed to lock it.
A vibration-isolating NEMA 17 motor mount: the motor bolts to a floating 46 mm plate (31 mm square M3 pattern, 22.5 mm pilot-boss bore) that is joined to a 76 x 76 mm outer frame only by four Z-shaped flexure beams, so motor buzz never reaches the chassis or the gyro. The frame bolts down with four M3 screws on a 68 mm cross pattern; print it as shown (flat, no supports) and flip it in use so the motor plate floats 6 mm clear of the chassis, leaving room for the motor screw heads.
An L-bracket that mounts a NEMA 17 stepper to 2020 aluminium extrusion: 54 x 40 mm base with two M5 T-nut holes on 20 mm centres, and a 54 x 50 mm vertical face carrying the 31 mm square M3 bolt pattern plus a 22.6 mm pilot bore for the motor's centring boss. Twin 5 mm gussets carry motor torque in the strong XY direction and sit outboard of the bolt heads so a hex driver still reaches all four screws; a pair of 6 x 3 mm slots above the bore takes a cable tie for the motor lead.
A U-bracket that slips over a cabinet door (fits panels up to 19.5 mm thick) and turns the inside face into a grocery-bag trash caddy — the bag handles drop into a 9 mm trough behind an upturned lip so they can't slide off. 50 mm wide with two optional screw holes for a permanent mount.
A curved clip that wedges onto the rim of a 1-gallon paint can, giving you a clean edge to wipe your brush on and a slot to park it over the paint instead of on the rim. Spans a 50° arc of the can, about 74 mm wide.
A sealed shop bank that swallows used utility-knife blades, snap-off tips and razor blades through a narrow funneled slot in its peaked roof, so they never end up loose in a drawer or trash bag. 58 x 42 mm footprint, 54 mm tall, holds a few hundred blades before you tape the slot and dispose of the whole thing.
A slip-on soft jaw cap for a bench vise: the tapered channel wedges onto jaw plates 12.5–16.5 mm thick, and crossed 90° V-grooves cradle round bar either horizontally or standing upright. 80 mm long, 30 mm tall — print two, one for each jaw.
A no-screw C-clamp that slides onto a desk edge or shelf and hangs your headphones underneath on a wide 30 mm saddle. The wedged inner jaw self-tightens on tops from 20–30 mm thick, and the 14 mm hook mouth also takes a bag or lanyard.
A two-horn wall cleat for figure-eight wrapping an extension cord, air hose or rope, with flared post tips that keep the coil from slipping off. 120 mm wide, mounts with two countersunk screws and holds roughly a 50 ft 16-gauge cord.
A 147 mm staircase block that stands a 13-piece metric drill index upright, with bores from 1.5 mm to 7.5 mm rising left to right so the size order is obvious at a glance. Each step is taller than the last, so bit tips sit deep and shanks stay easy to grab.
A screw-on wall gripper whose springy C-jaws snap over a 20–26 mm broom, mop, rake or squeegee handle so it hangs off the floor. 60 mm back plate with two counterbored screw holes; 18 mm tall jaws with a 19 mm snap mouth.
A wall or pegboard-mountable rail with eight graduated blind holes (8-16mm) that hold metric sockets by friction, keeping them lined up and visible on a workbench. Overall size 150 x 30 x 14mm with two mounting holes for screws.