Preview in 3D, we print and ship it — or download the file to print yourself.
Heads up: many models on this page are AI-generated or uploaded untested. They may be misconfigured for the intended application — check the dimensions and tolerances, and verify or edit the model before printing or relying on it.
A 68 × 38 × 5 mm carriage plate that bolts straight onto an MGN12H block (20 × 20 mm M3 pattern, heads recessed in 6.2 mm counterbores) and clamps both ends of a 6 mm GT2 belt on 2 mm-pitch tooth ridges, held by a zip tie through the four 4 × 3 mm slots. Four M3 heat-set bosses (4.0 mm bore, 6 mm deep) on a 38 × 25 mm grid give a flat tool deck for a gantry head, sensor or gripper — the piece a linear-rail axis normally needs but the rail kit never includes.
A weather cap for a nominal 4x4 fence or deck post (88.9 mm actual) with a 91 mm square socket, 20 mm engagement and two M4 clearance holes so it screws down and won't blow off. Twin horns on opposite faces carry a cafe-string-light cable in an 8 mm wide, 10 mm deep slot; overall 127 x 97 x 50 mm with a hollow 50-degree pyramid roof that sheds water and prints support-free.
A clamp-on double hook that saddles the top edge of a frameless glass shower door — towel hook on the outside, loofah/razor hook on the inside, no drilling, adhesive or suction cup. The 13.6 mm slot with a raised grip pad takes 6–13 mm (1/4"–1/2") tempered glass, and an M4 heat-set insert (5.5 mm bore) plus an M4x16 screw locks it down; 76 x 43 x 26 mm.
A 60-tooth GT2 timing pulley (2 mm pitch, 37.7 mm tooth OD, 41.7 mm flanges) with an 8.3 mm slip-fit bore for 8 mm shaft and a split-clamp hub tightened by a single M3 screw against a captured M3 nut. 22 mm tall with a 7 mm flanged belt land for 6 mm GT2 belt — the big reduction pulley you can't buy off-the-shelf in 8 mm bore.
A print-in-place GT2 belt tensioner that bolts to any frame face with two M5 screws and T-nuts (holes 64 mm apart, on the 2020 slot centreline) and gives 16 mm of idler travel from a single M3 x 20 screw that self-taps into the 7 mm end wall. The flanged 16 mm idler pulley (7 mm belt channel for 6 mm GT2) prints already captured on its own post, so there is no bearing, shoulder bolt or spring to source; overall 76 x 32 x 33.5 mm, three pieces, one print.
A split collar that clamps onto a standard 1/2" NPT shower arm (21.3 mm OD pipe) with one M4 screw into a heat-set insert, carrying two 30 mm upturned J-hooks for a loofah, razor strap or bottle handle — no suction cups, no drilling tile. Collar bore is 21.8 mm, ring wall 3.5 mm, overall 60 x 38 x 18 mm; slide it on with the shower head removed, then pinch the 3 mm gap closed to lock it.
A U-bracket that slips over a cabinet door (fits panels up to 19.5 mm thick) and turns the inside face into a grocery-bag trash caddy — the bag handles drop into a 9 mm trough behind an upturned lip so they can't slide off. 50 mm wide with two optional screw holes for a permanent mount.
A working barrel-bolt latch that prints fully assembled — the red bolt slides inside the grey housing with 0.4 mm clearance, no assembly and no supports. 76 mm housing with four screw ears; the bolt throws 27 mm past the end to catch a cabinet, shed door, gate, or toy box.
A three-step cabinet riser that stair-steps spice jars so every label is visible from the front. 80 mm wide x 108 mm deep x 66 mm tall, with a 3 mm lip on each tread so jars can't slide off; hollow open-bottom shell with internal ribs to keep it light.
A no-screw C-clamp that slides onto a desk edge or shelf and hangs your headphones underneath on a wide 30 mm saddle. The wedged inner jaw self-tightens on tops from 20–30 mm thick, and the 14 mm hook mouth also takes a bag or lanyard.
A 60 mm one-piece carabiner whose gate is a built-in flexing spring arm — press it inward to hook on, and a capture nose stops it opening under load. Prints flat with no supports, no assembly, and no metal spring; sized for keys, water bottles, and bag straps.