Preview in 3D, we print and ship it — or download the file to print yourself.
Heads up: many models on this page are AI-generated or uploaded untested. They may be misconfigured for the intended application — check the dimensions and tolerances, and verify or edit the model before printing or relying on it.
A cradle chassis for building a 3S (or 3P) 18650 pack: three 18.9 mm teardrop bores on 21.5 mm centres hold the cells in two 8 mm end collars plus a mid saddle, leaving both terminals flush with the outer faces at exactly 65 mm so nickel strip can be welded straight across. 82 x 68 x 34 mm, with raised + / − polarity ribs above each bore alternating for series wiring, four 3.4 mm M3 clearance holes to bolt the pack into a project, and four 12 x 5 mm zip-tie slots through the 3.5 mm base.
A print-in-place tilt-out parts bin: an 87 x 47 x 60 mm wall frame with a 70 x 41 x 50 mm bin hanging on captured 5 mm axles, so the bin self-closes by gravity and tips forward to pour screws or SMD parts into your hand. Mounts with two M4 screws through 4.5 mm holes on 56 mm centres, placed above the bin so a driver still reaches them; prints as one piece with no supports and 0.5 mm clearance on every mating face.
A bolt-clamped replacement slider/holder for a 25 mm shower riser bar, for when the molded plastic holder cracks and the maker only sells the whole $60 rail. A 38 mm split ring with 6.3 mm walls grips the bar via two M5x30 bolts with captured nut pockets, and a 10°-tilted tapered cradle (26.4 mm top, 22.8 mm bottom, open through the bottom so it drains) holds the hand shower. Overall 90 x 39 x 32 mm.
A clamp-on double hook that saddles the top edge of a frameless glass shower door — towel hook on the outside, loofah/razor hook on the inside, no drilling, adhesive or suction cup. The 13.6 mm slot with a raised grip pad takes 6–13 mm (1/4"–1/2") tempered glass, and an M4 heat-set insert (5.5 mm bore) plus an M4x16 screw locks it down; 76 x 43 x 26 mm.
A four-bay bench or wall caddy that stands RC LiPo packs upright, each bay 34 x 28 mm (fits packs up to about 33 x 27 mm in cross-section — the usual 2S/3S 1300–2600 mAh class) with a dedicated 10 mm rear channel per bay so the balance lead drops over a 36 mm divider wall and its plug hangs isolated from the neighbouring pack's main leads. Overall 148 x 47 x 52 mm, with a push-up window under each bay and two M4 clearance holes (4.5 mm) through the 4 mm back wall for wall mounting.
A split collar that clamps onto a standard 1/2" NPT shower arm (21.3 mm OD pipe) with one M4 screw into a heat-set insert, carrying two 30 mm upturned J-hooks for a loofah, razor strap or bottle handle — no suction cups, no drilling tile. Collar bore is 21.8 mm, ring wall 3.5 mm, overall 60 x 38 x 18 mm; slide it on with the shower head removed, then pinch the 3 mm gap closed to lock it.
A print-in-place hinged tilt bracket for small 10–100 W solar panels, 140 x 60 mm with a 5 mm base plate and a 60 mm-tall detent post. The base bolts to a roof rail, van rack or shed wall with four M5 lag screws (5.5 mm clearance holes) and the panel wing takes four M5 frame bolts; a single M5 x 60 bolt through the post and quadrant fin locks the tilt at 15°, 30°, 45° or 60°, with strap slots on both plates for frameless panels.
A 44 mm square block with four through-bores (18.7 mm, on 20.6 mm centres) that holds four 18650 cells upright, parallel and bottom-flush against the bench so nickel strip lands square during spot-welding or pack glue-up. Open-topped grab notches — one per cell, in 4-fold symmetry — let you spin a cell to set polarity, and two 5 mm ears with M3 clearance holes bolt the jig to the bench; overall 68 x 44 x 26 mm.
A gravity-fed dual-channel dispenser that stacks 6 AA and 8 AAA cells and drops the next one into a front grab window with a retaining lip. Stands 92 mm tall on a shelf or screws to a wall through the two rear ears.